Dogtra PATHFINDER2 User manual

1
PATHFINDER2
PT20U, PR20U
EXPLORE MORE - ADVANCED GPS TRACKING & TRAINING
Owner's Manual
Please read this manual thoroughly
before operating the Dogtra PATHFINDER2.

32
IMPORTANT SAFETY AND PRODUCT
INFORMATION
OWNER SAFETY
Handling and Repair
Dogtra products can be damaged or malfunction if dropped, especially on
hard surfaces, or otherwise improperly handled. Do not use a damaged or
malfunctioning product as it may cause injury or property damage. If your
product is damaged or malfunctions, contact Dogtra to obtain service before
using the product.
Electrical Product
Your Dogtra product contains electrical components and batteries. Do not use
or keep your product near heat or flammable sources. Such use or storage may
damage your product and/or cause fire, explosion, injury, or property damage.
Charging
Only charge your Dogtra product with its accompanying Dogtra charger. Do
not attempt to charge your product in any other manner or in temperatures
less than 32°F (0°C) or over 113°F (45°C) as it may cause fire, explosion, injury,
and/or property damage. If you notice damage to your product, its charger, or
battery, obtain service from Dogtra before charging the product. Do not use
more than one splitter cable with a single battery charger.
Medical Device Interference
Dogtra products contain electrical and magnetic components that emit low
level electromagnetic waves and radio frequencies. These electromagnetic
waves or radio frequencies may interfere with pacemakers, defibrillators, or
other medical devices. Consult your physician or medical device maker before
using your medical device with a Dogtra product. If you think that your Dogtra
product is interfering with your pacemaker, defibrillator, or other medical
device, stop using the Dogtra product.
Aggressive Dogs
Do not use Dogtra products with aggressive dogs as such dogs may react
adversely and cause injury to people or other dogs. Seek the assistance of a
dog-training specialist or veterinarian when dealing with aggressive dogs.
Children
Dogtra products are not toys. Adult supervision and close attention are
necessary when Dogtra products are used by or near children.
WARNING
Please read all safety and product information below before using your
Dogtra product. Failure to follow these safety instructions could result in
injury to you, your dog and others, or it could result in damage to your
Dogtra product or other property.
DOG SAFETY
Proper Use
Dogtra products should be used to train, educate, monitor, or track dogs. Each
dog may have a different tolerance for and reaction to Dogtra products. Closely
observe your dog when determining the right level of stimulation, receiver fit,
and other settings of your Dogtra product.
Training Methods
Dogtra products may be used with a variety of training methods that provide
clear and consistent messages to your dog.
Fit and Wear
Proper fit and wear of your Dogtra product is important for the comfort of
your dog as well as the functioning of your product. Dogtra receivers should
fit comfortably and not too tightly, so that the receiver stays in place and does
not move around your dog’s neck. Do not leave a receiver on your dog for an
extended time. Although each dog is different, Dogtra recommends that its
receivers be used a maximum of 4 to 6 hours at any one time on your dog.
A receiver that is used for overly long periods or that fits improperly may cause
skin irritation or sores on your dog’s neck. Regularly check the receiver's contact
area on your dog’s skin. If your dog exhibits skin irritation or sores, stop using
the Dogtra product and consult with a veterinarian.
UNAUTHORIZED USE
Dogtra products should be used only in a safe and responsible manner to train,
educate, monitor, or track dogs. Dogtra products are not intended for use in any
other manner; they are not intended for use with other animals or with humans;
and they are not intended for use in unsafe situations or environments that
could lead to death, injury, loss or damage.
BATTERY
Your Dogtra product contains batteries. Do not attempt to replace the battery
yourself. Contact Dogtra or your Dogtra retailer to replace your battery. Dispose
of batteries as provided by your local regulations. Do not disassemble, crush,
heat, or otherwise alter the battery as it may cause fire, explosion, injury and/or
property damage.

54
PACKAGE CONTENTS ...........................................................................................
MAIN FEATURES ....................................................................................................
OVERVIEW ...............................................................................................................
UNDERSTANDING YOUR TRAINING SYSTEM
BUTTON FUNCTION ........................................................................................
LED INDICATOR ...............................................................................................
GETTING STARTED
DOWNLOADING THE PATHFINDER2 APP ...............................................
ONLINE WEB MANUAL .................................................................................
PAIRING YOUR DEVICE .................................................................................
KEY FEATURES OF PATHFINDER2 APP ....................................................
OTHER FEATURES & DETAILS ...........................................................................
DEVICE INFORMATION
RECEIVER FITTING ..........................................................................................
FINDING THE RIGHT STIMULATION ...........................................................
MAXIMIZING THE DISTANCE ........................................................................
PRODUCT MAINTENANCE
CHARGING THE PATHFINDER2 ..................................................................
CHANGING THE CONTACT POINT LENGTH ............................................
USING THE TEST LIGHT ................................................................................
BASIC MAINTENANCE ..........................................................................................
TROUBLESHOOTING GUIDE ...............................................................................
FCC WARNING ........................................................................................................
WARRANTY AND REPAIR INFORMATION .....................................................
CONTENTS
6
7
8
11
12
13
13
14
16
32
33
34
35
36
37
38
40
41
42
43
1.
2.
1.
2.
3.
4.
1.
2.
3.
1.
2.
3.

76
PACKAGE CONTENTS
GPS Connector
(PT20U)
Battery ChargerPATHFINDER2: GPS Receiver
PATHFINDER2 TRX: GPS-Only Receiver
(PR20U)
Splitter Cable Owner’s Manual Belt Clip
Test Light * Contact Point
Extension Washer/
Adjustment Tool *
Non-Stimulation
Contacts *
MAIN FEATURES
2-Second GPS
Update Rate Offline Maps
2s
Precise and
Up-to-Date Maps
Tracking Only Mode*
9-Mile Range
9-Mile
IPX9K
Expandable to
21 Dogs
IPX9K Waterproof
Certified
Sleep Mode
21
Belt Clip
3.5-Hour Rapid
Charge Batteries
3.5
hr
For PATHFINDER2 TRX Only
* Not included with PATHFINDER2 TRX
* Not included with PATHFINDER2 TRX
UKC, AKC, and PKC Events Approved
Low-High Output in
1-100 Stimulation Levels*
Pager Vibration*
Nick/Constant
Stimulation*
E-Fence*,
Geo-Fence,
Mobile-Fence
Audible Tone*
Enhanced
Contact Points* TONE
C
NH

98
OVERVIEW
PATHFINDER2
GPS Connector (PT20U)
Battery Charging
Receptacle &
Rubber Plug
Power/Connect
Phone Button
Connect GPS
Receiver Button
Function
Button
MURS Band
Antenna
Battery Charging
Receptacle
Contact
Points
Power
Button
PATHFINDER2
GPS Receiver (PR20U)
Collar Strap
Mic. Sensor
GPS Antenna
Antenna
Casing
LED Locate light
MURS Band
Antenna

1110
PATHFINDER2 TRX
GPS-Only Receiver (PR20U)
Battery Charging Receptacle
Collar Strap
Mic. Sensor
GPS Antenna
Antenna
Casing
LED Locate Light
The PATHFINDER2 TRX does not have
contact points and does not come with
stimulation, vibration, or tone.
GPS Connector (PT20U)
GPS Receiver (PR20U)
POWER/CONNECT PHONE BUTTON
CONNECT GPS RECEIVER BUTTON
POWER BUTTON
FUNCTION BUTTON
• On: press the button until a green LED
light appears and 3 short beeps emit.
• Off: press the button until a red LED
light appears and 1 long beep emits.
• Use this button to pair a smartphone.
Find out more on page 14.
The Function button will emit the
e-collar function selected in the app
when pressed. Find out more on
page 21.
Use this button to pair a GPS receiver.
Find out more on page 15.
• On: press the button until a green LED
light appears and 3 short beeps emit.
• Off: press the button until a red LED
light appears and 1 long beep emits.
1. BUTTON FUNCTION
UNDERSTANDING YOUR TRAINING SYSTEM

1312
The LED on the GPS receiver blinks
every 2 seconds while turned on. The
LED colors represent the battery life:
Green: 50-100%
Orange: 10-49%
Red: 0-9%
2. LED INDICATOR
GPS Connector (PT20U)
The Power LED blinks every 2 seconds
while turned on. The LED colors
represent the battery life:
Green: 50-100%
Orange: 10-49%
Red: 0-9%
GPS Receiver (PR20U)
The app is currently compatible with:
1) Bluetooth 5.0 and above. Check the
version with the phone manufacturer.
2) iOS: 12.1 and above, iPhone 8 and above
3) Apple Watch Series 5 and above
4) Android: 6.0 and above
Compatibilities are subject to change.
PATHFINDER2
1. DOWNLOADING THE PATHFINDER2 APP
GETTING STARTED
QR CODE
Use the QR code to check out the full version of the
PATHFINDER2 manual and more. For more information,
please check www.DogtraPATHFINDER.com.
2. ONLINE WEB MANUAL
To download the app:
1) Go to the app store on your device.
2) Search for "Dogtra PATHFINDER2" app.
3) Download the app on your device.
Note: Make sure to download the Dogtra PATHFINDER2 app as the previous
app version is not compatible.

1514
F
U
N
C
T
I
O
N
CONNECT
GPS RECEIVER
POWER /
CONNECT
PHONE
3. PAIRING YOUR DEVICE
The PATHFINDER2 GPS connector connects a smartphone and receiver.
These devices need to be paired for the system to work properly.
Make sure the PATHFINDER2 app has
been downloaded on your phone. Turn
on Bluetooth on your phone and place
the GPS connector next to your phone.
In the app, go to the Menu tab and
click on 'Connection Failed with GPS
Connector.' Press the 'Connect' button
once the pairing screen shows on the
app.
Make sure the GPS connector is off.
Press and hold the Power/Connect
Phone Button until a green LED light
flashes and a melody plays to search
for your phone.
Power/
Connect
Phone
Button
PAIRING THE GPS CONNECTOR TO A PHONE
1
3
2
P
P
C
C
P
P
~
F
U
N
C
T
I
O
N
CONNECT
GPS RECEIVER
POWER /
CONNECT
PHONE
HON
E
P
P
F
U
N
C
T
I
O
N
CONNECT
GPS RECEIVER
POWER /
CONNECT
PHONE
PAIRING THE RECEIVER TO THE GPS CONNECTOR
1
3
2
4
~
Your phone should show a connection
completion screen and the green
LED will blink slowly on your GPS
connector.
Make sure the receiver is turned off.
Press and hold the power button for
more than 3 seconds until the green
LED rapidly flashes and a melody
plays. Release the button.
Make sure the connector is turned
on. Press and hold the Connect GPS
Receiver Button until the green LED
rapidly flashes.
The pairing is complete when the
melody stops and the LED lights stop
rapidly flashing.
F
U
N
C
T
I
O
N
CONNECT
GPS RECEIVER
POWER /
CONNECT
PHONE
F
U
N
C
T
I
O
N
CONNECT
GPS RECEIVER
POWER /
CONNECT
PHONE
Connect
GPS
Receiver
Button
C
G
C
C
G
G

1716
Icon Description
1My Position
The blue dot will show your location on the map. Press the My
Position button on the bottom right corner to recenter your location
on the map.
2Dog Position
The dog icon shows your dog’s current action status. It also provides
Traveled Distance, Current Speed, Altitude, Battery, Updated Time,
and Shared Device.
3Create Marker
Press the icon to add a marker. You can create markers for ‘My
Truck’ (car location), Truck, Dog, Tree, Favorite, or Note.
4Map Selection
Select general, satellite, or terrain map.
My Position
Dog Position
My Position
Map Selection
Create Marker
Main menu tab
4-1. MAP
4. KEY FEATURES OF PATHFINDER2 APP
1
2
1
4
3
Zoom
• Zoom in once: double tap the map with one finger.
• Zoom out once: single tap the map with two fingers.
• Use two fingers to pinch screen to zoom in and stretch the screen to zoom out.
Scroll
• You can scroll by using one finger to drag the map to the area you want to view.
Tilt
• Tilt the map by using two fingers and dragging the map up or down.
Rotate
• Rotate the map by using two fingers and applying a turning motion.
2) Dog Icons
1) Map Features
Icon Description
Default Status:
No motion detected.
Bark:
When the dog is barking.
Pointing:
When the dog is not moving and pointing towards game.
Treeing:
When the dog has two paws up on the tree to force animals up the
tree.
Running:
When the dog is moving quickly.
Hog:
When multiple dogs bark within 20 meters of the receiver.
PATHFINDER TRX Receiver:
Receiver cannot use e-collar functions.

1918
4-2. TOOLS TAB
Icon Description
Recording:
Record sessions for location and statuses. Replay sessions from
the History List on the menu.
Stopwatch:
Measure the amount of time that has elapsed, which will be visible
on the map.
Track:
View track lines on the map for past 5 hours and reset any track
information.
Timer:
Set a timer that will alarm at the end of a time interval, which will
be visible on the map.
Distance:
Measure the distance between two points on the map.
Navigation:
Use Google Maps to navigate to the marked location. Google Maps
must be installed.
Icon Description
No GPS:
Receiver cannot connect to GPS and cannot send location.
No RF:
Devices are far apart. Move the GPS connector to a higher area to
receive signal.
Recharge Battery:
Less than 20% battery life remains.
Share:
Appears when another user’s devices are shared.
Cannot use e-collar functions on shared devices.
E-Fence On:
Receiver has been synced with the E-Fence.

2120
4-3. COMPASS TAB
The Compass tab allows you to:
- View the direction and distance of dogs, selected marker, or hunter at a glance
by swiping the bottom slider up.
- See each marker by swiping the slider left or right on the smallest slider size.
- Add ‘My Truck’ marker to view distance and direction.
- Use the 'View All' button to view all dogs and hunters at once. Dogs and
hunters are not displayed when hidden or offline.
4-4. E-COLLAR TAB
Nick/Constant
Nick will emit a single rapid pulse of stimulation.
Constant will provide continuous stimulation as
long as the button is pressed, up to 12 seconds.
Stimulation Level
Set the stimulation from level 1-100 using the
slider. Press and hold the button on the slider to
turn the Lock feature on or off.
Pager
Press Pager to emit the Pager as long as the
button is pressed, up to 12 seconds.
Tone
Press Tone to emit a sound as long as the button
is pressed, up to 12 seconds.
Locate Light
Press the Locate Light button to turn the light on
or off.
Notes:
• Metal phone cases or metal objects attached to the phone will interfere
with the compass.
• The phone may need to be calibrated for the compass to work properly.
Lock Button
Press Lock to disable functions to prevent accidental stimulation until unlocked.
If Lock is on in the app, the GPS connector Function button will be locked too.
Sending Commands
1. Select the device from map or list view.
2. Select Nick or Constant and set the stimulation level from 1 to 100, which can
be set for each dog.
3. You can also send commands such as Light, Tone, or Pager.
GPS Connector's Function Button
The last used e-collar command will be color selected in the app. The Function
Button on the GPS connector will operate the last selected command. Keep in
mind that if the Lock is on in the app, the GPS connector Function button will be
locked too.
Notes:
The E-Collar tab is disabled when the Tracking Only Mode is turned on in
the Settings menu. Dogs are not displayed when hidden or offline. The
PATHFINDER2 TRX receivers and shared receivers will not show on List view.

2322
4-5. FENCE TAB
- Mobile-Fence is created with a radius centered around your smartphone
(the blue point on the map).
- Status: Indication of receiver in or out of the fence.
- Count: Number of times the receiver has crossed the fence.
- Set the radius from 10 to 2,000 yards.
- Set the Mobile-Fence settings by going to MENU SETTING MOBILE-FENCE.
The PATHFINDER2 offers three types of fences for you to either receive a
notification of your dog crossing boundaries or to auto-correct your dog.
The types of fences included are:
1. Mobile-Fence: a fence setup that moves based upon your smartphone location
and will send you a notification.
2. Geo-Fence: a static fence setup that will send you a notification.
3. E-Fence: a static fence setup that will send your dog an auto-correction and
send you a notification.
1) Mobile-Fence (Notification Only)
Notes:
• The Mobile-Fence gives a notification on the smartphone, but does not
auto-correct the e-collar.
• The automatic e-collar correction will only work on the E-Fence.
- Create Geo-Fences for specific areas to get alerts
on your device.
- Status: Indication of receiver in or out of the fence.
- Count: Number of times the receiver has crossed
the fence.
- Set the Geo-Fence settings by going to
MENU SETTING GEO-FENCE.
2) Geo-Fence (Notification Only)
Setting up a Geo-Fence
1. Press the button.
2. Move the map and place the on the desired area.
3. Click 'Drop Point' to create a point for the fence boundary.
4. Press Undo to delete the last point.
5. Click the save button on the top right.
- You can create up to 15 Drop Points and up to 15 Geo-Fences.
- Edit and delete file names and fence locations in the Fence List.
Notes:
• The Geo-Fence gives a notification on the
smartphone, but does not auto-correct the
e-collar.
• The automatic e-collar correction will only
work on the E-Fence.

2524
Geo-Fence Settings
- You can create an alarm for both exiting and
entering the Geo-Fence.
- You can select different alarm types.
3) E-Fence (Auto-Correction)
About the E-Fence
Set up the static E-Fence boundary to auto-correct your dog and get
notifications on your phone. When using the E-Fence, keep in mind:
- This device is GPS operated and cannot be used indoors.
- Do not use this as a permanent fence solution as your dog can still cross the
Outer Fence. Previous retriever training is needed to train your dog to come
back over the Outer Fence.
- The receiver will not emit stimulation when bringing your dog back over the
Outer Fence to the IN area.
- Make sure that Bluetooth is on to sync your receiver to the E-Fence boundary.
- Make sure that when the E-Fence boundary is updated, the receiver is synced
again.
- A smartphone or GPS connection is not needed to operate, but the track
information and application notification will not be received.
1OUT: When moving out of the boundaries, the e-collar emits Constant
correction for 5 seconds.
2NEAR: The receiver emits a Pager vibration for 5 seconds when within 5
yards of the Outer Fence or Inner Fence.
3IN: Safe area with no correction.
4Outer Fence: One large fence on the outskirts.
5Near Area: Automatically created within 5 yards of the Inner and Outer
Fence.
6 Inner Fence: Up to 3 Inner Fences can be created in the Outer Fence.
Notes:
For the dog's safety, the stimulation will only last 5 seconds if the dog goes
out of the boundaries. Make sure your dog comes back in the boundary after
5 seconds.
Restrictions:
The fence boundary
design cannot
cross over.
The fence boundary
design cannot have
sharp pointed areas
with small angles.
Boundary design requires
following:
- Minimum 900yd area.
- Minimum distance of 10 yd
between each Drop Point.

2726
- ON/OFF: the E-Fence can be turned on/
off by toggling the button. When turned
on, the E-Fence Outer Fence shows up
and a blue light on the receiver turns on.
: E-Fence On Mark
- Status: Current receiver status of IN,
NEAR, or OUT. 'Need to update' will
show up if you need to update the latest
E-Fence boundary information.
- Count: The number of times the receiver
crossed the boundary.
- Stim Lvl: Displays the correction level
when activated. If it is not activated,
it will show OFF and you will need to
go to E-Fence Settings to activate the
stimulation setting. Creating the E-Fence
Click on Set E-Fence Boundary.
Setting up Outer Fence
1) Press thebutton for the Outer Fence.
2) Move the map and place theon the desired area.
3) Click ‘Drop Point’ to create a point for the fence boundary.
4) Repeat the process above to complete the boundary. Create the fence so it
goes in one direction.
5) Click the save button on the top right. Only one can be saved.
Setting up Inner Fence
1) The Outer Fence must be created first to create the Inner Fence.
2) Press thebutton for the Inner-Fence.
3) Drag the area of the map you want to create the fence to the center
with the .
4) Click ‘Drop Point’ to create a point for the fence boundary.
5) Repeat the process above to complete the boundary. Create the fence so it
goes in one direction.
6) Click the save button on the top right. Three can be saved.
- You can create 1 Outer-Fence and 3 Inner-Fences. All fences can use up to 15
points.
Notes:
When the E-Fence feature is turned on, the receiver synced with the latest
E-Fence boundary will have a blue LED. If there is no blue LED, sync the
receiver to the boundary by referring to "Syncing E-Fence Boundary to the
Receiver" on page 28.

2928
Applying Stimulation on the Receiver
1) Press the ▼button for the receiver on the menu.
2) Set the stimulation level.
3) Press update.
E-Fence Settings
- Set the E-Fence settings by going to
MENU SETTING E-FENCE.
- You can create an alarm for both exiting and
entering the E-Fence.
- You can select different alarm types.
Bluetooth Connection:
View the smartphone and GPS connector
Bluetooth connection. If the devices are
not paired, turn both the GPS connector
and smartphone’s Bluetooth off and then
back on.
Device List:
Find detailed device information and set
individual settings.
History List:
Play recorded history files. Convert files
to GFX and KML files to share.
Map Settings:
Manage Offline Maps and select the size
and information of the marker.
Settings:
Manage settings for different map
features.
App Description:
Describes basic contents.
1. Initial setup describes GPS connector
and receiver pairing.
2. Main function will describe each tab.
4-6. MENU
Terms of Use/Privacy Policy:
Check Terms of Use and Privacy Policy before use.
Manual:
Quickly browse the manual.
Sleep Mode:
Puts the receiver to sleep to preserve battery life. In sleep mode, the GPS signal
for the receiver is turned off and will reset when turned back on.
Notes:
• After changing the E-Fence boundary, you
must sync it again.
• Each receiver must be synced individually in
order for the E-Fence to operate.
Notes:
Go to E-Fence Settings to press the Activate
button to turn the E-Fence operation on or off
for each receiver.
Syncing E-Fence Boundary to the Receiver
In order to operate the E-Fence, the receiver must
be synced.
1) Turn the receiver on near the smartphone.
2) Press the Sync E-Fence Boundary button.
3) Look at the list to make sure the receiver is
synced.

3130
4-7. ACTIVITY MODE
Activity mode: select the hunting
type for your activity mode to change
the settings to receive device status
notifications.
Select the Activity Mode for Small
Game, Upland, Hog Hunting, or Custom.
The status alarm settings for Running,
Treeing, Pointing, Bark, and Hog will
change for each mode selected. You can
select the alarm you want in Custom
Mode.
- Select the device’s alarms based on your specific needs.
- You can set each device’s alarms by going to: Menu Device List
Select Device Alarm Setting.
- Refer to the table below for possible settings.
4-8. DEVICE ALERTS
Category Type of Alarm Setting Up Alarm
Dog Status Running, Treeing, Barking,
Pointing, Hog Barking.
Menu Setting
Activity Mode
Mobile-Fence Exiting fence, entering fence, or
both.
Menu Setting
Mobile-Fence
Mobile-Fence Alarm
Geo-Fence Exiting fence, entering fence, or
both.
Menu Setting
Geo-Fence Geo-
Fence Alarm
E-Fence Exiting fence, entering fence, or
both.
Menu Setting
E-Fence E-Fence
Alarm
E-Collar Using e-collar commands. Automatic
Battery Life 20%, 15%, 10%, 5% Automatic
Device Connection RF connection with the receiver
and if the receiver is working. Automatic
Bluetooth
Connection Connect or disconnect status. Automatic

3332
QR CODE
Use the QR code to check out the full version of the PATHFINDER2
manual and more. Go to www.DogtraPATHFINDER.com to see all
the app features, such as:
- History Record, File, Detail
- Device List Options
- Device List Sharing & Receiving
- Map Management
- App Settings
OTHER FEATURES & DETAILS
Proper Fit
Fit the receiver on either side of the dog’s windpipe so that the contact points
press firmly against the dog’s skin. You should be able to fit two fingers
underneath the collar strap.
Improper Fit
A loose fit can allow the receiver to move around on the dog’s neck and cause
irritation. If the receiver is too loose, the contact will be inconsistent and cause
inconsistent correction.
Attention!
While Dogtra uses medical grade stainless steel contact points and anti-
microbial plastic to protect the dog’s skin, leaving the receiver in the same
location for an extended period of time can cause skin irritation due to the
sensitivity from the contact points. Reposition the receiver every few hours
to move the contact points and remove the receiver after 8 hours of use.
Check for skin irritation each time you use the unit.
1. RECEIVER FITTING
DEVICE INFORMATION

3534
2. FINDING THE RIGHT STIMULATION
• Open the PATHFINDER2 app to the E-Collar tab and select your dog and
stimulation level.
• The stimulation levels are from 1 (lowest) to 100 (highest).
• Always start at the lowest level of stimulation and work your way up.
• The appropriate level can be found when your dog responds to the stimulation
with a mild reaction, such as a tensing of the neck muscles.
Note: Every dog has a different tolerance and reaction to the stimulation.
Please look at your dog’s reaction to find the right level of stimulation. The
stimulation level may vary depending on the situation and distractions. A
distracted dog will require a higher level of stimulation compared to when
there is no distraction. Caution!
Operating the PATHFINDER2 near tall buildings and other steel structures
will reduce the range of the GPS signal. Not acquiring a GPS signal for
prolonged periods of time while outside may indicate issues with the unit.
• The PATHFINDER2 has a 9-mile line of sight range.
• To get the greatest range, hold the GPS connector away from your body and
avoid touching the antenna.
• Keep your unit properly charged for maximum signal strength.
• The GPS connector device must be near your phone for proper operation,
preferably less than 33 feet.
3. MAXIMIZING THE DISTANCE
Typical rangeMaximum range Minimum range

3736
1. CHARGING THE PATHFINDER2
Fully charge the PATHFINDER2 GPS connector and receiver before the first use.
The PATHFINDER2 uses lithium polymer batteries.
• Only use official Dogtra chargers with the PATHFINDER2.
• Do not charge the PATHFINDER2 near flammable substances.
• Fully charge the PATHFINDER2 if storing for 1 month or longer.
When to Charge
• When the LED is red on the GPS connector or receiver.
• When the app displays low battery for the GPS connector or GPS receiver.
• When the LED on the transmitter or receiver will not come on.
How to Charge
1. Connect the charger to the GPS connector and receiver using the splitter
cable.
2. Plug the charger into a 120-volt outlet.
3. When fully charged, detach the cables and plug the rubber caps over the
charging ports on the GPS connector and receiver.
4. The LED will display red while charging and green when the unit is fully
charged. A depleted battery requires 3.5 hours to fully charge.
PRODUCT MAINTENANCE
Splitter Cable
Do not use more than one splitter cable with a single battery charger.
The Dogtra PATHFINDER2 comes with 5/8” contact points that can be extended
to 3/4” for dogs with longer coats.
To increase the length:
1) Use the included adjustment tool side marked 5/8” to unscrew the contact
points counter-clockwise.
2) Place the extension over the exposed threads, flat side down.
3) Place the contact points over the extensions and tighten clockwise using the
adjustment tool side marked 3/4”.
Caution!
Tighten until firmly in place. Be careful not to over tighten.
To shorten the length back to 5/8", use the adjustment tool marked 3/4" to
remove the extensions and then tighten the contact points clockwise using
the side marked 5/8".
2. CHANGING THE CONTACT POINT LENGTH

3938
1) Turn on the receiver and place the
test light over the contact points.
2) Press the Nick button in the
PATHFINDER2 app and the test light
will light up momentarily.
3) Press the Constant button in the
PATHFINDER2 app and the test light
will light up as long as the button is
pressed, for up to 12 seconds.
4) The test light will glow brighter at
higher levels of stimulation and
dimmer with lower levels.
3. USING THE TEST LIGHT
Note: The test light may not be visible if the intensity level is set below level ten.
• Make sure the rubber charging cap is securely in place on the GPS connector
or receiver when in use.
• Carefully inspect the unit for any missing parts or damage to the casing after
use. Damaged or broken casing may affect the waterproof guarantee on
the unit.
• The antenna must be securely in place for maximum range.
• Charge the unit for 3.5 hours before storing for extended periods.
• Charge the unit fully once a month while in storage or before use.
• Do not keep the unit exposed to extreme climates.
• Dogtra may include updates and improvements to the PATHFINDER2 app
which can be downloaded through the App Store and Google Play.
BASIC MAINTENANCE