DOM FAMILY Grand 360 Degree 4470 User manual

IMPORTANT: KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Grand 360 Degree Swivel Bassinet
MODEL NO.: 4470
USER MANUAL

Parts Lists
Please check to make sure that all of the following parts listed are
included in the box when opened. If there are any missing parts,
please contact Dream On Me before using the product.
Bassinet Frame
and Cover
Mattress support,
Bottom frame Upper Pole Lower Pole
Bottom Tray Height Adjuster Mattress Board Mattress Pad
Wrench Screw Driver
Metal Plate Bottom Tube x2
Lock Nuts x4
Screw x8
Caster x4 Short Screw x4
1

•DO NOT use this bassinet if you cannot exactly follow the instructions. Failure
to follow these warnings and the instructions could result in serious injury or
death.
•If a sheet is used with the mattress pad, use only the one provided by Dream
On Me, or one specifically designed to fit the dimensions of the mattress pad.
Make sure that the sheet securely tucks under the mattress pad on all sides to
avoid entanglement.
•DO NOT place this bassinet near a window or a patio door where a child could
reach the cord of a blind or curtain to avoid strangulation.
•DO NOT place pillows, comforters or soft mattresses in this bassinet.
•ALWAYS keep child within arm’s reach.
•To reduce the risk of SIDS, pediatricians recommend healthy infants be placed
on their backs to sleep, unless otherwise advised by your physician.
•Use ONLY the mattress pad supplied by Dream On Me with this bassinet.
NEVER add a pillow, comforter, or another mattress for padding.
•DO NOT place more than one infant in the bassinet.
•DO NOT carry or move bassinet with infant inside of it.
•ALWAYS lock the brakes when the infant is inside of the bassinet.
•Ensure that the product is securely on the stand before the child is placed into
the bassinet.
STRANGULATION HAZARD:
•DO NOT place cords, straps, decorative ribbons or similar items that could
become wound around the child’s neck in or near this bassinet. DO NOT add
additional strings or straps to the bassinet.
WARNING
SUFFOCATION HAZARD!
Infants have suffocated:
•In gaps between extra padding and side of the bassinet.
•On soft bedding.
2

Parts used in this stage
2.Place the 2 Bottom Tubes as shown
in Figure 3. Make sure that the 4
wheels contact the floor.
Figure 3
3 Place the Lower Pole on the X-shaped
Bottom Tubes as shown in figure 4. Figure 4
LOWER FRAME ASSEMBLY
3
Bottom Tray Height adjuster
Lower Pole
Bottom Tube x2
Metal Plate
Screw x8Wrench Screw Driver Lock Nuts x4
Caster x 4 Short Screw x 4
Figure 1
1.Insert one end of the Bottom
Tube into the hole of the Castor.
Use the Short Screw and screw
driver to join them together. See
Figure 1 and Figure 2
Figure 2

4.Use 4 screws, the 4 lock nuts, and
the metal plate to connect the Lower
Pole to the X-shape bottom tubes as
shown in Figure 5.
Use the wrench to tighten 4 screws.
5.Slide the Bottom Tray onto the Lower
Pole as shown in Figure 6.
Make sure that the bottom tray makes
contact with the X-shape bottom tubes.
Push slightly on all 4 corners of the
bottom tray.
6.Place the Height Adjuster on the top of
Lower Post.
Push in the side button on and then slide
the height adjuster down until it clicks into
place as shown in Figure 7.
Make sure that the adjuster button is
located on the same side as the upper
hole as shown in Figure 7A
LOWER FRAME ASSEMBLY
Metal Plate
Lock Nut
1. Push in 2. Slide
Down
4
Figure 7
Figure 6
Figure 5
Figure 7A
IncorrectCorrect

7.Open up the Bassinet Frame as shown
in Figure 8 (to the right). Keep the
bassinet frame upside down for the
following step.
Figure 8
Figure 9
MAKE SURE that the center plastic holder
faces up as shown in Figure 10.
If the mattress support bottom frame is
assembled in the wrong direction, it can not
match the Upper Pole (see next step).
Figure 10
UPPER FRAME ASSEMBLY
Parts used in this stage
Bassinet Frame
Upper Pole Mattress support,bottom frame
Screw x4Screw Driver
Face up
5
9. Use the 4 remaining screws to connect
the mattress support bottom frame to the
bassinet frame as shown in Figure 10.
8. Place the Mattress Support Bottom
Frame on the ends of the legs of the
bassinet frame. Make sure that the 4 ends
click into place as shown in Figure 9.

10.Slide the Upper Pole into the Center Plastic Holder by sliding the metal
plate into the 2 side channels until it is locked into place as shown in Figure 11.
Figure 11
UPPER FRAME ASSEMBLY
ATTACH THE UPPER FRAME TO THE LOWER FRAME
Center Plastic Holder
Metal Plate onUpper Pole
press this button
Figure 12
6
Figure 12A
IncorrectCorrect
11.Connect the Upper Pole to the Lower
Pole. Push down on the button of the height
adjuster to slide the lower frame onto the
Upper Pole as shown in Figure 12.
Make sure that you install it in the correct
direction as shown in Figure 12A

12. Place the mattress board into the
bassinet. Make sure that the locking
mechanism is aligned with the crossbar as
shown in Figure 13.
13. Push on the Mattress Board until the
locking mechanism clicks into place. Repeat
on the other side as shown in Figure 14
14. Place the mattress pad as shown in
Figure 15.
Figure 13
Figure 15
Figure 14
15.To Raise the Height of the Mattress Board:
Hold both sides of the bassinet and lift up to raise
the height as shown in Figure 16.
16. To Lower the Height of the Mattress Board:
Hold the button on the height adjuster with one hand
and lower it with the other hand.
Do not release your hand while operating. Figure 17.
Figure 17
PLACE MATTRESS BOARD & MATTRESS PAD
ADJUST THE MATTRESS BOARD HEIGHT
Figure 16
7

LOCK THE UPPER FRAME
19. To lock the swivel function, you need to fix
the top basket frame. There is a slide lock
under the basket frame as shown in Figure 20.
Slide the lock up until it enters the housing. If
you slide down this lock, then the swivel
function will be enabled.
8
Figure 20
LOCK AND UNLOCK THE WHEELS
To Lock the wheel, pull down the tab on the wheel.
To unlock the wheel, lift up the tab on the wheel.
•Caregivers must ensure that the bassinet is safe by checking regularly and
before placing the child in it, that every part is properly and securely in place.
•Check this bassinet regularly before using it. Do not use it if any parts are loose
or missing or if there are any signs of damage. DO NOT substitute parts. Contact
Dream On Me for replacement parts or additional instructions if needed.
CARE AND MAINTENANCE
Thank you for choosing Dream On Me and congratulations on joining
The DOM Family, a family that has been transforming lives for 30 years!
We appreciate your feedback and wish you the very best in the coming
years with your new addition. If you have any questions or concerns
please don’t hesitate to reach out and a trusted DOM representative will
assist you. Thank you again for entrusting us to supply you with the
safest, functional and affordable baby products and accessories. Feel
free to follow us on Facebook and Instagram for further opportunities
and offers.

Fabric Assembly:
Bassinet fabric may be removed for cleaning. Always follow instructions for removal and
applying. Bassinet fabric may be hand washed in mild detergent. Never use bleach. Dry
and iron on low setting for best appearance.
Frame:
Frame paint may be touched up as needed. Use only nontoxic paints approved for
children’s products. Check all frame fasteners occasionally. Tighten all screws and
bolts as necessary
1. Remove the mattress pad.
2. Store your bassinet in a cool, dry place.
This bassinet is guaranteed to meet all federal and provincial standards and will provide
many years of service provided you adhere to the guidelines provided for assembly,
maintenance and operation.
•Never aim a vaporizer or humidifier directly at the bassinet. The water vapor may
ruin the finish of the bassinet.
•For parts or assistance, contact us at 732-366-1788
REMOVE THE BASSINET FABRIC FOR WASHING
SPECIAL INSTRUCTIONS
CLEANING
DISASSEMBLY AND STORAGE
Unzip them and remove the 4 zippers under the fabric around the
bassinet for washing.
Dream On Me Inc.
1532 S Washington Ave,
Piscataway TWP, NJ 08854
Phone #: [phone]
Fax #: [phone]
MADE IN KUN SHAN, CHINA
9