DOM DR-72 RUGGED User manual

DR-72 RUGGED
Table Tennis Table
ASSEMBLY INSTRUCTIONS
1. Assembly should be completed on a level oor. Protect the table edge with, for example, cardboard or carpeting.
2. Remove those parts that are not screwed to the table top, then carefully remove this table top from the carton. Stand the table
top upright on its edge and carefully open legs to keep it standing as shown in Figure 1.
Please read the whole of Step 3 before completing it. As you read the instructions, refer to Figure 1.
3. Attach four of the leg braces (A) to the table tennis legs using the 1 3/4” bolts and 3/8” locknuts provided.
NOTE: It is imperative that these braces are placed as described below and shown in Figure 1. Failing to follow
instructions, the table will not close or open properly, table top may crack or table could fall open causing injury.
The leg braces closest to the table top must be assembled on
the outside of the legs (B & C) and the braces furthest from the
table top must be assembled on the inside of the legs (B & C).
This is extremely important for the proper operation of the
table.
The end of the side braces with the slight bend must be close to
the centre leg (B). The bends in the braces must face upwards.
Again, please refer to Figure 1.
Make sure that the bolts pass through the legs and leg braces
from the outside so that the head of the bolts are all towards the
outside of the nished table and the lock nuts are on the inside.
Tighten the lock nuts only nger tight at this time.
Steps:
Figure 1
PARTS LIST
Please note: This is a piece of equipment where extreme personal caution must be taken
during assembly and positioning (Step 10). Table being improperly lifted may lead to damage
and understructure going out of alignment. At least two people are required for the whole
assembly process.
Top braces on
the outside of legs
Bottom braces on
the inside of legs
C
B
A
The bends in the leg brace must face
upwards and be close to leg B.

8. Slide the other half of the table as close to the rst half as possible and insert the centre legs into the H-shaped pieces already
attached to the other half thereby connecting the two tables as shown in Figure 3. Using two self tap screws provided, secure the
top H-shaped piece in place. The bottom H-shaped piece will be secured later on.
9 Insert a side bracket such that the net anchor bar of the side bracket hangs over the top surface of the table tops. Secure it in place
with the self tap screws provided. See Figure 3.
10. Pull the tables down into playing position (ie. on its wheels as it is seen in Figure 5). Do this by standing next to the centre leg
support bracket, place your foot against the lowermost centre leg wheel, grasp table top and pull. It is necessary for two people to
perfom this operation, standing side by side as shown. See Figure 4.
Division of DOM Enterprises Mfg. Ltd.
957 Roselawn Avenue, Toronto, Ontario, Canada, M6B 1B6 TEL. [phone] FAX [phone] www.domsports.com
4. Remove the second top from the box and set it upright on its side, in the same manner as Figure 1.
The two centre legs (B) must be next to each and the two outer legs (C) must be at each end.
11. Now you can install the second side bracket such that the net anchor bar again hangs over the top surface of the table tops and
secure it in place with the self tap screws provided. At this point, place the table into its rollaway position as in Figure 6 to gain
easier access to these screws. Be sure to now also secure the second H-Shaped piece in place using the self tap screws as well.
Figure 5. Fully assembled in play position
13. Install net and post set. Slide the two “L” brackets into the net anchor bar.
Slide on the net provided, pull to desired tightness and secure in place by
tightening thumb screws by hand.
14. Figures 5 & 6 show a completed and fully assembled DR-72 table tennis
table in both its playing and fold up/roll away positions.
IMPORTANT: DO NOT OVER TIGHTEN!
Over-tightening will make it impossible to lower and raise the table into
playing position. Tighten nuts until there are approximately 1-2 threads
protruding through the nuts leaving at least 1/8” (4 mm) between the legs
and the braces allowing the table to open and close properly.
NOTE: The enclosed nuts are special safety “locknuts” designed to remain
in place without over-tightening. Installed correctly, they will never require
further attention.
12. Finish securing (ie. tightening) the nuts and bolts on the leg braces that were
installed in Steps 3 and 5. See important note below.
Figure 6. Fully
assembled table
in fold up and roll
away position
5. Repeat the installation of the leg braces for this side as in Step 3. Re-read Step 3 if necessary to
ensure proper installation of the leg braces.
6. Select the H-shaped pieces enclosed and insert the four wheels/casters, making sure that the
wheel stems are fully inserted. See Figure 2.
7. Insert both the H-shaped pieces into the centre legs on one half of the table. Refer to Figure 3.
Figure 2 - Step 6
Figure 4 - Step 10
Step 9 - Insert Side Bracket
and Secure with screws
B
Figure 3 -
Steps 7,8 & 9
Step 7&8
Insert & Secure
with screws
Step 7&8
Insert but secure later
It is imperative that the tightness of these scews is checked periodically. If left loose it could result in damage to the table.