Dometic P062 User manual

MARINE
MAGNETIC-DRIVE PUMPS
Form No. 341460 2022-12-16 | ©2022 Dometic Corporation
WARNING
Cancer and Reproductive Harm
www.P65Warnings.ca.gov
P030, P045, P062, P075, P100, P137, P150, P200
EN Magnetic-Drive Centrifugal Pump
Installation and Operation Manual........2

2EN
Contents Magnetic-Drive Centrifugal Pump
1 Explanation of Symbols and Safety
Instructions ............................ 2
1.1 Recognize Safety Information .............2
1.2 Understand Signal Words................2
1.3 Supplemental Directives .................3
1.4 General Safety Messages ................3
2 Intended Use ........................... 4
3 General Information ..................... 5
4 Specifications .......................... 5
4.1 Maximum Surface Temperature ...........5
4.2 Minimum Flow Rate.....................5
5 Installation ............................. 6
5.1 Selecting the Pump Location .............6
5.2 Rotating the Pump Head (Optional) ........6
5.3 Mounting the Pump ....................8
5.4 Connecting the Piping ..................8
5.5 Connecting a Drain Plug or Valve (Optional) . 9
5.6 Making the Electrical Connections.........9
6 Operation.............................. 9
6.1 Priming the Pump ......................9
6.2 Starting the Pump ......................9
6.3 Verifying the Rotation of the Motor........10
6.4 Shutting Down the Pump ...............10
7 Maintenance .......................... 10
7.1 Recommended Maintenance Schedule....10
7.2 Flushing and Draining the Pump..........10
7.3 Disassembling the Pump. . . . . . . . . . . . . . . . 11
7.4 Inspecting the Pump Components .......13
7.5 Installing Pump Wear Kit (Optional) .......13
7.6 Installing a Pump Wet End Replacement Kit
(Optional)............................14
7.7 Reassembling the Pump ................14
8 Troubleshooting ....................... 16
9 Disposal .............................. 16
10 Warranty Information................... 16
Contents
Service Center & Dealer Locations
Visit: www.dometic.com
Please read these instructions carefully and follow all instructions,
guidelines, and warnings included in this product manual in order to
ensure that you install, use, and maintain the product properly at all
times. These instructions MUST stay with this product.
By using the product, you hereby confirm that you have read
all instructions, guidelines, and warnings carefully and that you
understand and agree to abide by the terms and conditions as set
forth herein. You agree to use this product only for the intended
purpose and application and in accordance with the instructions,
guidelines, and warnings as set forth in this product manual as well
as in accordance with all applicable laws and regulations. A failure
to read and follow the instructions and warnings set forth herein may
result in an injury to yourself and others, damage to your product,
or damage to other property in the vicinity. This product manual,
including the instructions, guidelines, and warnings, and related
documentation, may be subject to changes and updates. For up-to-
date product information, please visit www.dometic.com.
1 Explanation of Symbols and
Safety Instructions
This manual has safety information and instructions to
help you eliminate or reduce the risk of accidents and
injuries.
1.1 Recognize Safety Information
This is the safety alert symbol. It is used to alert
you to potential physical injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
1.2 Understand Signal Words
A signal word will identify safety messages and property
damage messages, and also will indicate the degree or
level of hazard seriousness.
DANGER!
Indicates a hazardous situation that, if not avoided,
will result in death or serious injury.
WARNING
Indicates a hazardous situation that, if not avoided,
could result in death or serious injury.

3
EN
Magnetic-Drive Centrifugal Pump Explanation of Symbols and Safety Instructions
CAUTION
Indicates a hazardous situation that, if not avoided,
could result in minor or moderate injury.
NOTICE: Used to address practices not related to
physical injury.
IIndicates additional information that is not related
to physical injury.
1.3 Supplemental Directives
To reduce the risk of accidents and injuries, please
observe the following directives before proceeding to
install or operate this product:
• Read and follow all safety information and
instructions.
• Read and understand these instructions before
installing or operatingthis product.
• The installation must comply with all applicable local
or national codes, including the latest edition of the
following standards:
U.S.A.
– ANSI/NFPA70, National Electrical Code (NEC)
– American Boat and Yacht Council (ABYC)
Canada
– CSA C22.1, Parts l & ll, Canadian Electrical Code
1.4 General Safety Messages
WARNING: MAGNETIC HAZARD. Failure to
obey the following warnings could result in
death or serious injury:
• Individuals with cardiac pacemakers, implanted
defibrillators, other electronic medical devices,
metallic prosthetic heart valves, internal wound clips
(from surgery), metallic prosthetic devices or sickle
cell anemia must not handle or be in the proximity of
the magnets inside this pump. Consult a health care
provider before working with this pump.
• Do not place fingers between the mating surfaces of
the motor and wet end of this pump. The magnetic
force is powerful enough to rapidly pull the motor
end and the wet end together.
WARNING: ELECTRICAL SHOCK, FIRE, AND/
OR EXPLOSION HAZARD. Failure to obey the
following warnings could result in death or
serious injury:
• Use only Dometic replacement parts and
components that are specifically approved for use
with the product.
• Avoid improper installation, adjustment, alterations,
service, or maintenance of the product. Service and
maintenance must be done by a qualified service
person only.
• Do not modify this product in any way. Modification
can be extremely hazardous.
• Before attempting to make any electrical connections,
ensure the electrical power is off and the water valves
are completely closed.
• Secure and seal all wire connections to protect from
arcing.
• Do not operate the pump in a highly-explosive
environment unless the pump has a label to indicate
it is rated for ignition protection. Refer to labeling on
the pump to determine the environmental limitations
for operation near gasoline or other explosives.
• Do not pump flammable or combustible liquids.
• Disconnect the pump from the power supply before
cleaning and/or servicing. Maintenance must be
done by a qualified service person only.
WARNING: FLOOD/LEAK HAZARD. Failure to
obey the following warnings could result in
death or serious injury.
• Do not perform service or maintenance when the
pumping system is pressurized.
• Do not mount the pump such that high piping loads
exist on the pump connections, or in a rigid system
that does not allow the pipe to expand, causing the
pump to be strained.
• Do not operate the pump beyond the pressure or
temperature limits.
• Do not allow severe temperature changes to occur in
a short time period within the pumping system.
• Do not continue to operate the pumping system
when a known leak exists.

4EN
Intended Use Magnetic-Drive Centrifugal Pump
WARNING: IMPACT HAZARD.
This pump has components that rotate while
in operation. Follow local safety standards for
locking out the motor from the power supply
during maintenance or service. Failure to obey
this warning could result in death or serious injury.
WARNING: BURN HAZARD.
Do not touch the surface of the pump during
operation or before cool down. This pump can
handle liquids up to 180 ºF (82 ºC). This may cause
the pump to become hot and could cause burns.
Failure to obey this warning could result in death or
serious injury.
WARNING: CHEMICAL HAZARD. Failure to
obey the following warnings could result in
death or serious injury.
• Always wear protective clothing and eye protection
when handling chemicals that may be used to
operate or maintain this pump.
• Follow standard safety procedures when handling
corrosive or personally harmful materials that may be
used with this pump.
• Follow proper procedures for draining and
decontaminating the pump before performing
maintenance on it.
WARNING: LIFTING HAZARD.
This pump and associated components are heavy.
Do not attempt to li or move the pump without
adequate support. Failure to obey this warning
could result in death or serious injury.
NOTICE: Failure to obey the following instructions
could result in damage to the pump or components, and
cause property damage.
• Keep the drive magnet and impeller assembly
away from metal chips or particles, and items with
magnetic stripes like credit cards and magnetic
computer media such as floppy discs and hard drives.
• Do not li or move the pump without support. The
pump and components are heavy.
• Do not continue to operate the pump when unusual
noise or vibration occurs.
• Do not run the pump at less than the minimum flow.
This could lead to a pump failure.
• Do not continue to operate the pumping system
when a known leak exists.
• Do not operate the pump without liquid in the
casing. The exact length of time the pump can
operate dry without damage varies with operating
conditions and the environment.
• Do not start or operate the pump with a closed
suction valve.
• Do not operate the pump with a closed discharge
valve. This could lead to pump failure.
• Always provide adequate NPSHa (net positive
suction head available). It is recommended to
provide at least 24 in. (61 cm) above the NPSHr (net
positive suction head required).
• If the pump is used on variable speed drive, do
not exceed the frequency for which the pump was
designed (for example, if the pump is a 50 Hz model,
do not exceed 50 Hz).
• Ground the pump to prevent static discharge. Before
operating the pump, ensure the electrical continuity
throughout the pumping system and earth ground is
1 Ohm or less.
• Check the pump for leaks on a regular basis. If leaks
are noticed, immediately repair or replace the pump.
• Clean the pump regularly to prevent dust build up.
• Do not check the rotation of the motor without filling
the pump full of liquid, opening the suction and
discharge lines, and removing air from the lines.
• Use of a power monitor is strongly recommended for
pumps. The power monitor will stop the pump and
help prevent damage if the pump should run dry.
2 Intended Use
This Dometic Magnetic-Drive (Mag-Drive) Centrifugal
Pump (also referred to as the “pump” or the “product”)
is marine grade, intended for use with sea or nonpotable
water.
Pumps are designed to encompass a wide range of
applications and configurations. The installer determines
various installation factors to fit the application, such as:
• Pump head orientation (horizontal or vertical)

5
EN
Magnetic-Drive Centrifugal Pump General Information
• Mounting location (directly to floor plates, rails with
vibration isolators to reduce noise, platforms, etc.)
• Suitable mounting hardware for desired installation
or use
• Suitable piping for desired installation or use (for
example: Schedule 80 PVC, CPVC, copper piping,
stainless steel, flexible hose, etc.)
• Single-phase or three-phase electrical wiring
This manual provides all necessary information for
proper installation and operation of the pump. Poor
installation and improper operating procedures will
result in unsatisfactory performance and possible failure.
The manufacturer accepts no liability for damage in the
following cases:
• Faulty assembly or connection
• Damage to the product resulting from mechanical
influences and excess voltage
• Alterations to the product without express permission
from the manufacturer
• Use for purposes other than those described in this
manual
Dometic Corporation reserves the right to modify
appearances and specifications without notice.
3 General Information
IThe images used in this document are for reference
purposes only. Components and component
locations may vary according to specific product
models.
Recommended Tools and Materials
Wire Strippers and Crimper Phillips-head Screwdriver
Weatherproof Wire Nuts Socket Wrenches
• 5/16 in. (8 mm)
• 3/8 in. (9 mm)
• 1/2 in. (13 mm)
• 5/8 in. (16 mm)
• 3/4 in. (19 mm)
Other hardware sufficient for
secure mounting at desired
location
Additional Tools and Materials for Optional Steps
Drill Press Waterproof Pipe Sealant or
Tape
7/16 in. Drill Bit Drain Plug or Valve
1/4 in. NPT Tap Waterproof Electrical Tape
Arbor Press Plastic or Wooden Sha
4 Specifications
The major pump parts are glass-filled polypropylene for
superior corrosion resistance.
IFor best performance, maintain operation of
this pump within the following specifications.
Additional specifications for each pump are
available online at www.dometic.com.
4.1 Maximum Surface Temperature
The maximim allowable surface temperature of the
pump is 180 °F (82 °C).
4.2 Minimum Flow Rate
See the table below for the minimum flow rates by
model.
Model 3450 rpm 2900 rpm
P030 0.3 gpm (.9 lpm) 0.3 gpm (.9 lpm)
P045
P062
P075
P100
0.5 gpm (1.9 lpm) 0.5 gpm (1.9 lpm)
P137 4 gpm (15 lpm) 3.4 gpm (12.9 lpm)
P150 5 gpm (18.9 lpm) 4.2 gpm (15.9 lpm)
P200 10 gpm (37.8 lpm) 10 gpm (37.8 lpm)

6EN
Installation Magnetic-Drive Centrifugal Pump
5 Installation
NOTICE: Failure to obey the following instructions
could result in damage to the pump or components, and
cause property damage.
• The motor is splash-resistant, not submersible. It
should be located in a dry environment.
• The pump outlet must be above the inlet.
• Never install the pump vertically or with the motor
below the pump.
• If the pump was packaged with plastic shipping
shims, these shims must be used as additional
support under the motor feet.
• The Net Positive Suction Head available (NPSHa)
to the pump must be greater than the Net Positive
Suction Head required (NPSHr). NPSHa is the
pressure measured to the inlet of the pump. NPSHr
is a value that can be found on the pump spec sheet
curves. Filters, strainers and any other fittings in the
suction line will lower the NPSHa and should be
calculated into the application.
This section describes how to select the pump
location, how to rotate the pump head (if needed to
accommodate the discharge piping), mounting the
pump, connecting the piping, connecting a drain plug
or valve, and making the electrical connections.
5.1 Selecting the Pump Location
When selecting the pump location, consider the
following items.
qq
wer
t
y
u
i
1 Pump Placement - Sea or Nonpotable Water Application
qWater Line yStrainer
wSeawater Outlet uInlet Flow
eOutlet Flow iSeacock (ball valve)
and Scoop-type,
Through-hull Inlet
rA/C Condenser Coil
tPump
• For optimum performance and to minimize suction
li, place the pump as far below the water line as
possible.
• Place the pump in a location that will allow mounting
in a level, horizontal position, on a secure foundation.
• Ensure adequate ventilation around the pump for
proper operation and cooling of the motor.
5.2 Rotating the Pump Head
(Optional)
The pump is preconfigured with a vertical discharge
orientation, which is applicable to most installations.
When preparing the pump installation, it may be
necessary to rotate the pump head to improve the ease
of installing the pump and associated piping. Rotating
the pump head is optional, and should be done before
mounting the pump.
IMake sure the o-ring is properly seated in the
groove aer rotating. The o-ring is lubricated, and
should not need additional lubrication.
IWhen the pump discharge is in a horizontal
configuration, the motor must be shimmed to raise
the front of the pump to avoid interference.

7
EN
Magnetic-Drive Centrifugal Pump Installation
5.2.1 P030 Model
Use the following instructions to rotate the pump head
on the P030 model.
q
w
2 P030 Discharge Orientations
qVertical Discharge wHorizontal Discharge
1. Place the motor in an upright position, resting on the
fan end of the motor.
2. Remove the eight screws from the pump housing.
3. Pull the housing away from the motor adapter/
barrier.
4. Rotate the housing 90°, aligning the screw holes on
the housing and motor adapter/barrier.
5. Push down on the housing to seat it on the motor
adapter/barrier.
6. Reinstall the screws.
5.2.2 P045, P062, P075, P100, P137,
P150, and P200 Models
Use the following instructions to rotate the pump head
on the P045, P062, P075, P100, P137, P150, and P200
models.
q
w
3 P045, P062, P075, P100, P137, P150, and P200 Discharge
Orientations
qVertical Discharge wHorizontal Discharge
1. Remove the four clamp ring bolts, lock washers, and
flat washers.
2. Rotate the clamp ring 90°, aligning the holes on the
clamp ring and motor adapter/barrier.
3. Reinstall the clamp ring bolts, lock washers, and flat
washers.

8EN
Installation Magnetic-Drive Centrifugal Pump
5.3 Mounting the Pump
Use the following instructions to securely mount the
pump in the desired location.
q
e
w
r
4 Mounting With Vertical Discharge Orientation (P030 Shown)
qSealant eFoot
wMotor rPump Head
1. Place the pump motor in the desired location and
mark the position of the mounting holes.
2. Drill holes for the mounting screws.
3. If the pump was packaged with plastic shipping
shims, place the shims under the motor feet.
4. Tighten the screws to secure the pump into position.
5. Use an appropriate pipe sealant or tape on the
threads and other piping connections.
6. Tighten all connections, using appropriate tools for
the selected piping materials.
5.4 Connecting the Piping
Use the following guidelines for connecting the piping.
• Place the piping with independent support near the
pump to eliminate any strain on the pump casing.
• A strainer on the inlet pipe should be used to remove
debris before the liquid enters the pump.
• Position the piping on the suction side of the pump
in a straight and short configuration to minimize pipe
friction.
• Keep bends and valves at least ten pipe diameters
away from the suction and discharge.
• Install the suction piping to be level or sloping slightly
upward toward the pump. To prevent air pockets, the
suction line should not have any high spots.
• The suction line should be at least as large as the
suction inlet port or one pipe size larger so that it
does not affect the NPSHa. Do not reduce the suction
line size.
• A check valve and control valve (if used) should be
installed on the discharge line. The check valve helps
prevent the pump from water hammer damage. This
is particularly important when the static discharge
head is high. The control valve is used for regulating
flow.
• Isolation valves on the suction and discharge lines
can be used to make the pump accessible for
maintenance.
• If flexible hose is preferred, use a reinforced hose
rated for the proper temperature, pressure and
chemical resistance against the fluid being pumped.
• Use an appropriate pipe sealant or tape on the
threads and other piping connections.
• The suction valve must be completely open to avoid
restricting the suction flow.
• A flush system in the piping can be installed to allow
the pump to be flushed before it is removed from
service.
IP062, P075, P100, P137, P150, and P200 pump
models are provided with a provision for a
customer-installed 1/4 in. (6 mm) drain in the
impeller housing. For the best performance, ensure
the pump piping is sized appropriately for the flow
rate.

9
EN
Magnetic-Drive Centrifugal Pump Operation
5.5 Connecting a Drain Plug or Valve
(Optional)
A drain plug or valve can be installed in the impeller
housing to provide the ability to connect a drain line
for removing fluids before servicing the pump. The
following instructions explain how to connect an
optional drain plug or valve on the P062, P075, P137,
P150, and P200 models.
1. Clamp the impeller housing to a drill press table.
2. Using a 7/16 in. drill and the molded boss as a guide,
drill completely through the molded boss into the
interior of the impeller housing.
3. Using a 1/4 in. NPT tap, tap the hole in the molded
boss to the appropriate depth.
IDo not tap too deep or the impeller housing may
be damaged.
4. Install the drain plug or valve, being careful not to
over-tighten.
5.6 Making the Electrical
Connections
NOTICE: When installing the pump, follow these
important considerations regarding the electrical
connections. Failure to follow the practices listed could
result in damage to the pump.
• Prior to connecting to the power line, check the
nameplate voltage and rotation connection, and
ensure proper grounding.
• Check the pump voltage, frequency, and phase to
ensure it matches the installation power source.
• Do not use or install the pump if the voltage,
frequency, phase, and amp on the label are different
from the supply circuit.
• Protect the motor with a fuse or circuit breaker. For
three-phase motors, protect the motor with a phase-
failure protection device.
• Some pumps are dual-voltage and will need to be
wired to the specific voltage for your application.
• If utilized, verify that power monitors or variable
frequency drives have been properly installed
according to the manufacturer’s instructions.
• Follow National Electric Code, NEMA MG-2, IEC,
and ABYC standards, requirements, and local
electrical codes.
IRefer to the wiring diagram affixed to the pump.
6 Operation
NOTICE: This pump must be filled with liquid. Failure
to prime the pump before operation could result in
damage to the pump and components.
Follow the steps in this section for priming and starting
the pump, verifying the motor rotation, and shutting
down the pump.
6.1 Priming the Pump
IThis pump is not self priming. Mounting the pump
below the water line helps prime the pump head.
1. Connect the external liquid source to the pump.
2. Open the inlet (suction) and discharge valves
completely and allow the pump to fill with liquid.
6.2 Starting the Pump
1. Ensure all valves are open and the pump connections
are secure. The pump requires positive suction at the
pump head to prevent cavitation.
2. Close the discharge valve.
3. Turn the pump on.
4. Slowly open the discharge valve. Adjust the flow rate
and pressure by regulating the discharge valve.
IDo not attempt to adjust the flow with the suction
valve.

10 EN
Maintenance Magnetic-Drive Centrifugal Pump
6.3 Verifying the Rotation of the
Motor
1. Allow the motor to run for 1-2 seconds and observe
the rotation of the motor fan.
2. Refer to the directional arrow molded into the pump
casing or the rotational sticker at the rear of the pump
motor. If the motor rotation direction matches the
direction the arrows are pointing, rotation is correct.
If the rotation is incorrect, check the wiring diagram
on the pump and resolve wiring issues.
IA pump running backwards will pump but at a
greatly reduced flow and pressure.
6.4 Shutting Down the Pump
1. Turn off the motor.
2. Slowly close the discharge valve.
3. Close the suction valve.
7 Maintenance
NOTICE: Failure to properly maintain the pump may
void the warranty and could result in unsafe operation.
Preventive maintenance is not covered under the
warranty.
NOTICE: Before performing maintenance on this pump,
it must be flushed and drained of all fluids.
The following maintenance and cleaning instructions
should be performed at the intervals indicated, or as
needed, depending on the use of the pump.
7.1 Recommended Maintenance
Schedule
The recommended maintenance schedule depends
upon the nature of the fluid being pumped and the
specific application.
• If the pump is used on a clean fluid, remove the pump
from service and perform an inspection aer six
months, or aer 2,000 hours of operation.
• If the pump is used on fluids with solids, high
temperatures, or other items that could cause
accelerated wear, then this initial examination should
be sooner.
• For the best results, remove the pump from service at
least annually for disassembly and inspection.
Aer the initial examination of the internal components
and wear items are measured, a specific maintenance
schedule can be determined.
7.2 Flushing and Draining the Pump
IDrain the pump of fluids to remove internal pressure
before performing maintenance.
1. Follow the proper shut down procedure. Refer
to “Shutting Down the Pump” on page 10 for
instructions.
2. Connect the flushing fluid supply to the inlet valve.
3. Connect the flushing fluid drain to the discharge
valve.
4. Open the flushing inlet and discharge valves.
5. Direct the flushing liquid into the system until the
pump is clean.
6. Stop the flow of flushing liquid and allow the pump to
drain of all fluids.

11
EN
Magnetic-Drive Centrifugal Pump Maintenance
7.3 Disassembling the Pump
q
wr t
y
d
fh
g
5 Exploded View - P030
i
u
y
e
rt
w
q
os
a
dh
g
f
6 Exploded View - P045, P062, P075, P100

12 EN
Maintenance Magnetic-Drive Centrifugal Pump
q
y
w
e
r t
u
h
g
j
df
sao
i
7 Exploded View - P137, P150, P200
qPump Housing tImpeller Drive Assembly oBarrier O-Ring fOuter Drive Magnet
wHousing O-Ring yImpeller Bushing aClamp Ring (not
included on P200)
gMotor Sha
hMotor
eImpeller Thrust Ring uImpeller Sha sClamp O-Ring jFoot (not included
on P200)
rImpeller Assembly iMotor Barrier dMotor Adapter
1. Shut down the pump, lock out the motor from the
power supply, flush the pump, and drain all fluid.
Refer to “7.2 Flushing and Draining the Pump” on
page 10.
2. For small pumps 2 hp (1.5 kW) or less, place the
pump and motor in an upright position on the fan
end of the motor or securely clamp the foot to a
workbench. For larger pumps with 3 hp (2.2 kW) or
greater, place the pump securely on the floor with the
pump head facing up.
3. Remove the screws or bolts and lock-washers (if
present) securing the pump head to the motor
adapter/barrier. Use tools appropriate for the
fasteners installed. (The P030 motor adapter includes
the barrier, while other models have a separate motor
barrier and motor adapter.)
4. Firmly hold one side (either the pump head or the
motor, depending on the size and weight of the
model) and pull straight out to disengage the pump
head and motor. If the pump head has the optional
o-ring seal, make sure the o-ring remains on the
motor adapter.
5. Place the pump head on a workbench with the
housing facing up.
6. Remove the screws or bolts on the outside of the
pump housing. The number of housing fasteners
depends on the pump model.
7. Firmly hold the pump housing and pull straight up to
remove it from the pump head.
8. Remove the impeller thrust ring, the impeller
assembly, the impeller drive assembly, and the
impeller bushing.
9. Remove the impeller sha. On the P030, the impeller
sha is attached to the motor adapter. For all other
models, the impeller sha is attached to the motor
barrier.
10.Remove the motor barrier and barrier o-ring (if
present) from the motor adapter. If necessary, gently
tap on the backside of the motor barrier with a so
wooden or plastic rod to dislodge it. (This step does
not apply to the P030.)
11. Remove the clamp ring and clamp o-ring from the
motor adapter. (This step does not apply to the
P030.)
INuts may become bonded to the studs over time.
Tightening the nuts before removal ensures the
studs do not back out of the pump head.

13
EN
Magnetic-Drive Centrifugal Pump Maintenance
7.4 Inspecting the Pump
Components
• Check the pump housing for signs of wear or
damage. Look for signs of rubbing, cracking on thrust
ring, or damage to the front sha support.
• Check the impeller, drive, thrust ring, bushing, and
running surface between the impeller and the pump
head for wear.
• Replace the bushing if wear causes the dimensions of
the bushing to exceed the maximum diameter limit.
Refer to “Impeller Bushing Wear Tolerance” on page
13 for acceptable dimensions.
• Check the inside and outside of the motor barrier for
wear or signs of rubbing.
• Check the outer drive for rubbing, damage,
corrosion, or loose magnets.
• Check the o-ring for chemical attack, swelling,
brittleness, cuts, or other damage. Replace the o-ring
if it is worn or damaged.
• Check the clamp ring for wear. If it is damaged, it
should be replaced.
• Clean the parts that are to be reused using a mild
cleanser. Remove any abrasive material.
• Check the motor sha for wear at the seal. If it shows
signs of wear, replace the pump.
• Check the motor bearings by rotating the motor
manually. If the sha rotation is not smooth or has
radial/axial end-play, replace the pump.
IIf needed, contact Dometic Customer Support for a
pump wear kit or pump wet end replacement kit.
7.4.1 Impeller Bushing Wear Tolerance
Use the following diagram and table to determine the
wear on the impeller bushing. If the measured inner
diameter exceeds the maximum tolerance, replace the
bushing.
q
8 Impeller Bushing Wear Tolerance
Model
qMaximum Impeller
Bushing Inner Diameter
P030
P045
P062
P075
P100
0.415 in. (10.5 mm)
P137
P150 0.515 in. (13.1 mm)
P200 0.780 in. (19.8 mm)
7.5 Installing Pump Wear Kit
(Optional)
If the impeller bushing must be replaced, follow the
instructions below to install the impeller bushing wear
replacement kit (sold separately) before reassembly.
1. Place the impeller/inner drive assembly with the
impeller facing up in an arbor press. If necessary
support the bottom of the assembly with blocks to
allow the bushing to fall out.
2. Insert a 1 in. (25 mm) diameter plastic or wooden
sha through the impeller and press the bushing out.
3. Remove the impeller assembly from the arbor press.
4. Place the impeller assembly on a flat surface with the
impeller thrust ring face down.
5. With the slotted face of the replacement bushing
facing the rear of the inner drive, align the flat in the
bushing with the flat in the inner drive magnet.
6. Gently push the bushing into the inner drive until the
bushing bottoms out.
7. Follow the instructions in “7.7 Reassembling the
Pump” on page 14 to reassemble the pump.

14 EN
Maintenance Magnetic-Drive Centrifugal Pump
7.6 Installing a Pump Wet End
Replacement Kit (Optional)
If any of the pump components besides the impeller
bushing require replacement, follow the instructions
below to install the pump wet end replacement
kit before reassembling the pump. This kit is sold
separately. It includes the pump head that attaches to
the motor.
1. For small pumps 2 hp (1.5 kW) or less, place the
pump in an upright position on the fan end of
the motor or securely clamp the pump feet to a
workbench. For larger pumps with 3 hp (2.2 kW) or
greater, place the pump and motor securely on the
floor with the pump head facing up.
2. Remove the screws or bolts and lock-washers (if
present) securing the pump head to the motor
adapter/barrier. Use tools appropriate for the
fasteners installed.
3. Firmly hold the pump head (or the side that is not
clamped) and pull straight out to disengage the
pump head and motor.
4. Align the holes on the replacement pump wet end
assembly with the holes on the motor adapter.
5. Install the screws or bolts and lock washers (if
present).
IRefer to Figure 9, 10, or 11 on page 1514-15
(depending on the pump model) for a reassembly
diagram.
7.7 Reassembling the Pump
q
wr t
y
d
f
h
g
9 P030 Reassembly
i
u
y
e
rt
w
q
os
a
df
g
h
10 P045, P062, P075, P100 Reassembly

15
EN
Magnetic-Drive Centrifugal Pump Maintenance
q
y
w
e
rt
u
h
g
j
df
s
a
o
i
11 P137, P150, P200 Reassembly
qPump Housing tImpeller Drive Assembly oBarrier O-Ring fOuter Drive Magnet
wHousing O-Ring yImpeller Bushing aClamp Ring (not
included on P200)
gMotor Sha
hMotor
eImpeller Thrust Ring uImpeller Sha sClamp O-Ring jFoot (not included
on P200)
rImpeller Assembly iMotor Barrier dMotor Adapter
1. Place the clamp o-ring on the clamp ring, and install
it on the motor adapter. Press firmly to ensure a tight
seal. (This step does not apply to the P030).
2. Place the barrier o-ring on the motor barrier and
install it on the motor adapter. (This step does not
apply to the P030).
3. Install the impeller sha, aligning the flats on the
sha with the ones in the motor barrier. Make sure
the impeller sha is completely seated in the motor
barrier. (This step does not apply to the P030).
4. Assemble the impeller thrust ring, the impeller drive
assembly, and the impeller bushing. (The P030
impeller assembly has the thrust ring and drive
assembly included within it.)
5. Place the housing o-ring in the groove on the pump
housing and apply an oil-free lubricant.
6. Install the pump housing onto the pump, making
sure the discharge is in the correct orientation for the
installation.
7. Holding the pump housing with one hand, install
and finger-tighten two bolts or screws and washers (if
present) in opposite locations.
8. Install the remaining pump housing fasteners and
finger-tighten.
9. Use a socket wrench or screwdriver (depending
on fasteners) to tighten all bolts evenly using a star
pattern.
IRefer to Figure 9, 10, or 11 on page 1514-15
(depending on the pump model) for a reassembly
diagram.

16 EN
Troubleshooting Magnetic-Drive Centrifugal Pump
8 Troubleshooting
Use the instructions that follow to resolve occurrences that are not a result of defective workmanship or materials.
Problem Possible Cause Recommended Solution
The flow is insufficient or
nonexistent.
There is an air leak in the suction piping. Check the pipe connections and tighten the seals.
The pump has not been primed. Ensure the pump head is filled with fluid before starting.
The system head is higher than expected. Check the application requirements; a larger pump may
be required.
There is a closed valve. Open the suction and discharge valves.
The viscosity or specific gravity is too high. Check the fluid mixture concentrations.
The suction li is too high or there is
insufficient NPSH.
Ensure the proper inlet pressure. The pump should be
either below water level or in a fully pressurized loop.
There is a clogged suction line or impeller
vane.
Check the inlet strainer and pump lines, and remove
debris.
The motor is rotating incorrectly. Check the wiring to ensure the installed configuration
matches wiring diagram on the pump.
The pressure is low. There is air or gas in the liquid that is running
through the pump.
Bleed the air out of the system using an automatic bleeder
or manually open a bleeder line at the highest point.
The impeller diameter is too small. Check the application requirements; a larger pump may
be required.
The system head is lower than expected. Check the application requirements; a smaller pump may
be required.
The motor is rotating incorrectly. Check the wiring to ensure the installed configuration
matches the wiring diagram on the pump.
The pump is no longer
primed.
There is a leak in the suction piping. Check the pipe connections and tighten the seals.
The pump is using an
excessive amount of power.
The voltage is too low. Check the generator power output to ensure it is
maintaining the proper voltage.
The specific gravity or viscosity is too high. Check the fluid mixture concentrations.
The pump is vibrating or
making a loud noise.
The pump is cavitating from improper suction
or feed.
Ensure the proper inlet pressure is maintained. Check the
inlet strainer and the pump lines, and remove debris.
The pump is not mounted securely. Use vibration isolators between the pump mount and the
mounting surface.
9 Disposal
MPlace the packaging material in the appropriate
recycling waste bins, whenever possible. Consult
a local recycling center or specialist dealer for
details about how to dispose of the product in
accordance with all applicable national and local
regulations.
10 Warranty Information
LIMITED WARRANTY AVAILABLE AT
WWW.DOMETIC.COM/WARRANTY.
IF YOU HAVE QUESTIONS, OR TO OBTAIN A COPY
OF THE LIMITED WARRANTY FREE OF CHARGE,
CONTACT:
DOMETIC CORPORATION
MARINE CUSTOMER SUPPORT CENTER
2000 NORTH ANDREWS AVENUE
POMPANO BEACH, FLORIDA, USA 33069
1-800-542-2477

17
EN
Magnetic-Drive Centrifugal Pump Warranty Information

18 EN
Warranty Information Magnetic-Drive Centrifugal Pump

19
EN
Magnetic-Drive Centrifugal Pump Warranty Information

A complete list of Dometic companies, which comprise the Dometic Group, can be found in the public filings of:
DOMETIC GROUP AB Hemvärnsgatan 15 SE-17154 Solna Sweden
dometic.com
YOUR LOCAL
DEALER
dometic.com/dealer
YOUR LOCAL
SUPPORT
dometic.com/contact
YOUR LOCAL
SALES OFFICE
dometic.com/sales-offices
341460 2022-12-16