Domino F Series User manual

Domino F-Series
Product Manual
F220i

(2) EPT009665 Issue 2 May 2015
Note: This manual EPT009665 is intended for use only with the
F-Series product with a BCP7 Controller.

EPT009665 Issue 2 May 2015 (3)
WARNINGS:
AS SUPPLIED, THIS CODER IS A CLASS 4 LASER PRODUCT. DURING
OPERATION, IT WILL EMIT UP TO 40 WATTS OF PULSED INVISIBLE
LASER RADIATION AT A WAVELENGTH BETWEEN 1030 AND 1120
NANOMETERS. AVOID EYE OR SKIN EXPOSURE TO DIRECT OR
SCATTERED RADIATION.
THE PRODUCTS CONTAIN EMBEDDED LASER DEVICES THAT EMIT
INVISIBLE RADIATION IN THE REGION OF 900 - 1000 NM WITH A
TOTAL OUTPUT POWER OF UP TO 120 W FOR THE RATED OUTPUT
POWER OF THE LASER MODULES: THIS RADIATION IS NOT
ACCESSIBLE TO THE USER UNLESS THE PROTECTIVE HOUSING IS
OPENED.
THE LASER MAY EMIT SIGNIFICANTLY HIGHER POWERS UNDER A
SINGLE FAULT CONDITION (<120 W 1030 – 1200 NM; <100 W 900 –
1000 NM).
THIS CODER MUST BE FITTED WITH CLASS 1 LASER GUARDING TO
SAFEGUARD AGAINST ACCIDENTAL EXPOSURE TO DIRECT OR
SCATTERED RADIATION BEFORE IT IS OPERATED OR MADE READY
FOR USE.
GUIDANCE ON CREATING AND FITTING LASER GUARDING CAN BE
FOUND IN PART 1 OF THE PRODUCT MANUAL.
USE OF CONTROLS OR ADJUSTMENTS OF PERFORMANCE OR
PROCEDURES OTHER THAN THOSE SPECIFIED IN THIS MANUAL
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

(4) EPT009665 Issue 2 May 2015
THIS PAGE INTENTIONALLY LEFT BLANK

EPT009665 Issue 2 May 2015 (5)
DOMINO F-SERIES LASER CODER
WARNING: This is a Class 4 Laser using high power invisible
infrared light. A risk of personal injury or damage
to equipment may result if proper safety
precautions are not observed. Reading and
understanding this manual is required before
operating this laser system.
This manual, Domino Part No. EPT009665, has been produced for use in
the maintenance and operation of the Domino F-Series Laser Coder, and to
reinforce and complement any training program available with the product.
It is not designed to replace any such training program.
All rights reserved. No part of this publication may be reproduced, stored
on a retrieval system, or transmitted in any form, or by any means,
electronic, mechanical, photocopying, recording or otherwise, without the
prior permission of Domino Printing Sciences plc.
Domino Printing Sciences plc has a policy of continuous product
improvement. The Company, therefore, reserves the right to modify the
specification contained in this manual without notice.
For sales and service assistance please visit the following website and
select “Contact Domino in your country” for local technical support:
http://www.domino-printing.com
© Domino Printing Sciences plc 2015
Domino Printing
Sciences plc
Bar Hill
Cambridge
CB23 8TU
United Kingdom
Tel: [phone]
Fax: [phone]

(6) EPT009665 Issue 2 May 2015
CONTENTS OF THE
EC DECLARATION OF CONFORMITY
(in accordance with ISO/IEC 17050-1)
No. EPT009665/2
Issuer’s name: Domino Laser GmbH, Germany
Issuer’s Address: Fangdieckstrasse 75a, 22547 Hamburg / Germany
Object of the declaration: F-Series laser marking system consisting of:
Controller F220i (BCP7), Laser Unit and optional TouchPanel.
The object of the declaration described above is in conformity with the
requirements of the following documents:
EN 61000-6-2:2005 Electromagnetic compatibility (EMC) - Part 6-2:
Generic standards - Immunity for industrial environments.
EN 60825-1:2014 Safety of Laser Products.
EN 55011:2007 + A2:2007 Industrial scientific and medical (ISM) radio-
frequency equipment - Electromagnetic disturbance characteristics -
Limits and methods of measurement (IEC/CISPR 11:2003 + A1:2004,
modified + A2:2006)
EN 60950-1:2006/A1:2010 Safety of Information Technology Equipment.
EN 61326-1:2006 Electrical equipment for measurement, control and
laboratory use - EMC requirements - Part 1: General requirements (IEC
61326-1:2005)
EN ISO 13849-1:2008 Safety of machinery - Safety related parts of
control systems - Part 1
2006/95/EC: Low Voltage Directive
2004/108/EC: EMC Directive
2011/65/EU: RoHS2 Directive
Additional Information
Compliance is dependent upon installation and use in accordance with the
Product Manual supplied.

EPT009665 Issue 2 May 2015 (7)

(8) EPT009665 Issue 2 May 2015
CONTENTS OF THE
EU DECLARATION OF INCORPORATION
(in accordance to the Directive 2006/42/EC on Machinery appendix II I.B for
partly completed machines)
No.: EPT009665/2
Issuer‘s Name: Domino Laser GmbH
Issuer‘s Address: Fangdieckstrasse 75a, 22547 Hamburg, Germany
Person authorised to compile the relevant technical documentation,
who must be established in the Community: Research & Development
Department, Domino Laser GmbH
Object of the declaration: F-Series laser marking system consisting of:
Controller F220i (BCP7), Laser Unit and optional TouchPanel.
The special technical documents corresponding to the machine have
been created according to Appendix VII, part B.
It is expressly stated that the partly completed machine fulfills all the
relevant provisions of the following EC directives.
2006/42/EU Directive 2006/42/EC of the European parliament and
of the Council of 17 May 2006 on machinery, and
amending Directive 95/16/EC (recast)
2006/95/EU Directive 2006/95/EC of the European parliament and
of the Council of 12 December 2006 on the
harmonisation of the laws of Member States relating
to electrical equipment designed for use within certain
voltage limits
2004/108/EU Directive 2004/108/EC of the European parliament
and of the Council of 15 December 2004 on the
approximation of the laws of the Member States
relating to electromagnetic compatibility
and repealing Directive 89/336/EEC
2011/65/EU Directive 2011/65/EU of the European parliament and
of the Council of 8 June 2011 on the restriction of the
use of certain hazardous substances in electrical and
electronic equipment (recast)

EPT009665 Issue 2 May 2015 (9)
Published applied harmonized standards according to Article 7 (2)
Published other applied technical standards and specifications
We commit to transmit, in response to a reasoned request by the
surveillance authorities, relevant documents on the partly completed
machinery. Property rights of the manufacturer of the partly completed
machinery remain unaffected.
Important Note
The partly completed machinery must not be put into service until the
final machinery into which it is to be incorporated has been declared in
conformity with the provisions of this Directive, where appropriate.
EN 60204-1:2006-06 Safety of machinery - Electrical equipment of
machines. Part 1: General requirements.
EN 61000-6-2:2005 Electromagnetic compatibility (EMC) - Part 6-2:
Generic standards - Immunity for industrial
environments.
EN 60825-1:2014 Safety of Laser Products.
EN 55011:2007 +
A2:2007
Industrial scientific and medical (ISM) radio-
frequency equipment - Electromagnetic
disturbance characteristics - Limits and
methods of measurement (IEC/CISPR 11:2003
+ A1:2004, modified + A2:2006)
EN 60950-1:2006/
A1:2010
Safety of Information Technology Equipment.
EN 61326-1:2006 Electrical equipment for measurement, control
and laboratory use - EMC requirements - Part 1:
General requirements (IEC 61326-1:2005)
EN ISO 13849-1:2008 Safety of machinery - Safety related parts of
control systems - Part 1
ÖNORM EN ISO
11252 2013 -12-01
Lasers and laser-related equipment - Laser
device - Minimum requirements for
documentation (ISO 11252:2013); German
version EN ISO 11252:2013

(10) EPT009665 Issue 2 May 2015

EPT009665 Issue 2 May 2015 (11)

(12) EPT009665 Issue 2 May 2015
CERTIFICATION
Industrial Laser Unit for Marking:
Controller F220i (BCP7),
Laser Unit F220i.
Approved by Certificate No.: CU72150806 01

EPT009665 Issue 2 May 2015 (13)
FCC NOTICE
PART 18 USERS MANUAL STATEMENT
This equipment has been tested and found to comply with the limits of ISM
Equipment pursuant to Part 18 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a typical
installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communication. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Re-orientate or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the manufacturer
could void the user's authority to operate the equipment.

(14) EPT009665 Issue 2 May 2015
MICROSOFT’S EMBEDDED SYSTEMS END
USER LICENSE AGREEMENT (“EULA”)
• You have acquired a device (“DEVICE”) that includes software licensed
by Domino Printing Sciences plc from Microsoft Licensing Inc. or its
affiliates (“MS”). Those installed software products of MS origin, as
well as associated media, printed materials, and “online” or electronic
documentation (“SOFTWARE”) are protected by international
intellectual property laws and treaties. The SOFTWARE is licensed, not
sold. All rights reserved.
• IF YOU DO NOT AGREE TO THIS END USER LICENSE AGREEMENT
(“EULA”), DO NOT USE THE DEVICE OR COPY THE SOFTWARE.
INSTEAD, PROMPTLY CONTACT DOMINO PRINTING SCIENCES PLC
FOR INSTRUCTIONS ON RETURN OF THE UNUSED DEVICE(S) FOR
A REFUND. ANY USE OF THE SOFTWARE, INCLUDING BUT NOT
LIMITED TO USE ON THE DEVICE, WILL CONSTITUTE YOUR
AGREEMENT TO THIS EULA (OR RATIFICATION OF ANY PREVIOUS
CONSENT).
GRANT OF SOFTWARE LICENSE. This EULA grants you the following
license:
• You may use the SOFTWARE only on the DEVICE
• NOT FAULT TOLERANT. THE SOFTWARE IS NOT FAULT TOLERANT.
DOMINO PRINTING SCIENCES PLC HAS INDEPENDENTLY
DETERMINED HOW TO USE THE SOFTWARE IN THE DEVICE, AND
MS HAS RELIED UPON DOMINO PRINTING SCIENCES PLC TO
CONDUCT SUFFICIENT TESTING TO DETERMINE THAT THE
SOFTWARE IS SUITABLE FOR SUCH USE.
• NO WARRANTIES FOR THE SOFTWARE. THE SOFTWARE is
provided “AS IS” and with all faults. THE ENTIRE RISK AS TO
SATISFACTORY QUALITY, PERFORMANCE, ACCURACY, AND
EFFORT (INCLUDING LACK OF NEGLIGENCE) IS WITH YOU.
ALSO, THERE IS NO WARRANTY AGAINST INTERFERENCE WITH
YOUR ENJOYMENT OF THE SOFTWARE OR AGAINST
INFRINGEMENT. IF YOU HAVE RECEIVED ANY WARRANTIES
REGARDING THE DEVICE OR THE SOFTWARE, THOSE
WARRANTIES DO NOT ORIGINATE FROM, AND ARE NOT BINDING
ON, MS.
•Note on Java Support. The SOFTWARE may contain support for
programs written in Java. Java technology is not fault tolerant and is
not designed, manufactured, or intended for use or resale as online
control equipment in hazardous environments requiring fail-safe
performance, such as in the operation of nuclear facilities, aircraft
navigation or communication systems, air traffic control, direct life
support machines, or weapons systems, in which the failure of Java
technology could lead directly to death, personal injury, or severe

EPT009665 Issue 2 May 2015 (15)
physical or environmental damage. Sun Microsystems, Inc. has
contractually obligated MS to make this disclaimer.
• No Liability for Certain Damages. EXCEPT AS PROHIBITED BY LAW,
MS SHALL HAVE NO LIABILITY FOR ANY INDIRECT, SPECIAL,
CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM OR
IN CONNECTION WITH THE USE OR PERFORMANCE OF THE
SOFTWARE. THIS LIMITATION SHALL APPLY EVEN IF ANY
REMEDY FAILS OF ITS ESSENTIAL PURPOSE. IN NO EVENT
SHALL MS BE LIABLE FOR ANY AMOUNT IN EXCESS OF U.S.
TWO HUNDRED FIFTY DOLLARS (U.S.$250.00).
•Limitations on Reverse Engineering, Decompilation, and
Disassembly. You may not reverse engineer, decompile, or
disassemble the SOFTWARE, except and only to the extent that such
activity is expressly permitted by applicable law notwithstanding this
limitation.
•SOFTWARE TRANSFER ALLOWED BUT WITH RESTRICTIONS. You
may permanently transfer rights under this EULA only as part of a
permanent sale or transfer of the Device, and only if the recipient
agrees to this EULA. If the SOFTWARE is an upgrade, any transfer
must also include all prior versions of the SOFTWARE.
EXPORT RESTRICTIONS. You acknowledge that SOFTWARE is of US-
origin. You agree to comply with all applicable international and national
laws that apply to the SOFTWARE, including the U.S. Export Administration
Regulations, as well as end-user, end-use and country destination
restrictions issued by U.S. and other governments. For additional
information on exporting the SOFTWARE, see http://www.microsoft.com/
exporting/.
© 2000 Microsoft Corporation. All rights reserved. Terms of use.

(16) EPT009665 Issue 2 May 2015
LICENCE NOTES FOR DYNAMARK
Dynamark 3 uses code of the following projects:
• STLport (http://stlport.sourceforge.net)
• Boost (http://www.boost.org)
• libSigC++ (http://libsigc.sourceforge.net)
• FreeType (http://www.freetype.org)
• zlib (http://www.zlib.net)
• dxflib (http://www.ribbonsoft.com/de/about-dxflib)
• SQLite (http://www.sqlite.org)
• Lua (http://www.lua.org)
• FreeImage (http://freeimage.sourceforge.net)

EPT009665 Issue 2 May 2015 (17)
LIABILITIES AND WARRANTIES
Warranty and liability rights for personal or material damages are precluded,
if they are caused by one of the following:
• Non-designated use of the laser marking system
• The use of consumer-electronics (e.g. PDAs or Mobiles) as user
interface for the marking laser systems is not recommended nor
supported
• Unauthorized installation or configuration of software on the controller.
• Unauthorized execution or configuration of programs on operating
system level. On integration of the laser marking system into a TCP/IP
network the Domino Laser GmbH excludes liability for all damages that
are caused by attacks on the controller (like viruses, worms). The laser
marking systems are built for integration in a secure industry network.
• Improper installation, commissioning, operating, and maintaining of
the laser marking system
• Operating the equipment with defective safety installations, or
improperly installed or inoperable safety and protective devices
• Non-compliance with the instructions of the operating manual
regarding transport, storage, installation, commissioning, repairs, or
maintenance of the laser marking system
• Opening the laser unit
• Unauthorised structural modifications to the laser marking system
• Unauthorised modifications of the beam and laser parameters
• Inadequate monitoring of components
(Refer to PART 5 MAINTENANCE AND FAULT FINDING)
• Disasters, war, and acts of God.

(18) EPT009665 Issue 2 May 2015
CONTENTS
PART 1 HEALTH & SAFETY
PART 2 INSTALLATION INSTRUCTIONS
PART 3 OPERATION
PART 4 TECHNICAL REFERENCE
PART 5 MAINTENANCE AND FAULT FINDING
APPENDIX A MARKING FONTS
APPENDIX B BARCODES

EPT009665 Issue 2 May 2015 (19)
AMENDMENT RECORD
Amendment Date
All Parts at Issue 1 September 2013
All Parts at Issue 2 May 2015

(20) EPT009665 Issue 2 May 2015
THIS PAGE INTENTIONALLY LEFT BLANK