Domus Ventilation DX Series Instruction Manual

2.0 Introducon
The Domus DX Window Fan Kit is available in 6, 9 and 12 inch impeller
sizes suitable for supply or extract and can be the heart of a room’s
automac venlaon system.
Ensure adequate air replacement for the fan and any fuel burning
appliance in the room.
3.0 Dimensions
2.1 Switching
Operated via a separately wired 3 amp fused spur (by others) or operated
via the optional DX-CON remote controller allowing supply or extract,
variable speed and automatic or manual switching of several fans if
desired.
2.2 Sensors
Sensors are available as remote units or integral ‘plug in’ units. They
are able to control mulple fans, depending on sensor and fan types.
Integral sensors are quick and easy to install and are aesthecally
pleasing, whilst remote sensors give the benefit of locaon close to
the pollutant source. Remote sensors can be fied with an oponal
security strap to prevent unwanted tampering.
2.3 General
The removable interior grille provides easy access while the external
rotor motor makes for simple removal of the push-on impeller for
cleaning. Upward angled interior grille vanes shield workings from view
and downward sloping external vanes throw off rain. The fan is IP24
splash proof approved with the motor rated at IP44.
All external components are made in so grey colours from ultra violet
stable ABS material so they will blend with most decors and will not
fade in sunlight.
2.3.1Coding For Window Fan Kits
Window Fan Kits are supplied as a complete package with all
window installaon parts included and are suitable for glazing
thickness of up to 32mm and wall/panels of 360mm.
Outer grille
Clamping plate
Spacer
Fan plate assembly
Inside grille
Figure 1. Main components of Window installaon assembly.
Figure 2.
Descripon Code*
6 inch Window Fan Kit Complete DX6WW
9 inch Window Fan Kit Complete DX9WW
12 inch Window Fan Kit Complete DX12WW
1.0 Safety Informaon
IMPORTANT: Installaon or replacement of units or spare parts must be carried out by a qualified
or Domus approved service engineer/ electrician and in accordance with IEE or local naonal wiring
regulaons.
269 mm
134 mm*
269mm
137mm*
128mm
272mm
DX6WW (6 inch)
Front view
DX9WW (9 inch) DX12WW ( 12 inch)
Rear view
Side view
Cable entry
Aperture required
184mm dia.
*To centre of
'duct'
337 mm
171 mm*
342mm
175mm*
130mm
342mm
Cable entry
*To centre of
'duct'
413mm
206 mm*
420mm
214 mm*
169 mm
420mm
Cable entry
*To centre
of 'duct'
Aperture required
260mm dia.
Aperture required
337mm dia.
269 mm
134 mm*
269mm
137mm*
128mm
272mm
DX6GL (6 in ch)
Front view
DX9GL (9 in ch) DX12GL ( 12 inch)
Rear view
Side view
Cable entry
Aperture required
184mm dia.
*To centre of
'duct'
337 mm
171 mm*
342mm
175mm*
130mm
342mm
Cable entry
*To centre of
'duct'
413mm
206 mm*
420mm
214 mm*
169 mm
420mm
Cable entry
*To centre
of 'duct'
Aperture required
260mm dia.
Aperture required
337mm dia.
269 mm
134 mm*
269mm
137mm*
128mm
272mm
DX6GL (6 in ch)
Front view
DX9GL (9 in ch) DX12GL ( 12 inch)
Rear view
Side view
Cable entry
Aperture required
184mm dia.
*To centre of
'duct'
337 mm
171 mm*
342mm
175mm*
130mm
342mm
Cable entry
*To centre of
'duct'
413mm
206 mm*
420mm
214 mm*
169 mm
420mm
Cable entry
*To centre
of 'duct'
Aperture required
260mm dia.
Aperture required
337mm dia.
E
VE N T I L A T I O N
DX Window Fan Kit 50Hz/60Hz
Supply / Extract Units – Installaon and Maintenance
LAB1350R May 2018 Page 1

LAB1350R May 2018 Page 2
V E N T I L A T I O N
4.0 Installaon
4.1 Installaon of Window Fan Kits
Remove adhesive pad covers.
Clean the window glass and affix the
outer grille assembly over window aperture.
1
2
3
5
4
6
7
8
Prepare the window.
Remove front grille.
Release 2 screws. Lift grille upwards.
Feed supply cable into the case.
Remove fan plate.
DX6WW
Required Glass Aperture
184 dia
260 diaDX9WW
XS 1 337 dia
Ensure rubber seal is located into case spigot.
Fix outer grille to spigot plate. Check plate orientaon is
vercal. Note grille locates over top lugs on spigot plate.
4.0 Installaon
4.1 Installaon of Window Fan Kits
Remove adhesive pad covers.
Clean the window glass and affix the
outer grille assembly over window aperture.
1
2
3
5
4
6
7
8
Prepare the window.
Remove front grille.
Release 2 screws. Lift grille upwards.
Feed supply cable into the case.
Remove fan plate.
Required Glass Aperture
184 dia
260 dia
DX6WW
DX9WW
XDX12WW 337 dia
Ensure rubber seal is located into case spigot.
Fix outer grille to spigot plate. Check plate orientaon is
vercal. Note grille locates over top lugs on spigot plate.
Installation and Maintenance
DX Window Fan Kit 50Hz/60Hz

LAB1350R May 2018 Page 3
V E N T I L A T I O N
Installation and Maintenance
DX Window Fan Kit 50Hz/60Hz
Fit the inside grille, locang it over the top lip before
engaging screws.
9
10
11
13
12
Screw the case/ grille assembly together.
For various wiring opons see page 5.
Release the electrical cover from the fan plate.
Assemble the fan plate to the case.
IMPORTANT
(Shuer Operaon XS fans)
There will be a short delay on start-up and shutdown of
approximately 40 seconds, this is normal.
4.2 Fing Ancillaries (Also see page 8)
4.2.1 Thin Wall Installaon
The diagram shows the unit
installed in a mber wall.
A Wall Fixing Plate is used
to support the fan assembly
and the installaon is similar
to that for a window.
4.2.2 Weather Terminal
The oponal Weather Terminal is offered for use in exposed site
condions.
The illustraon shows the Weather Terminal installed replacing the
Outside Grille assembly. Terminal is held in posion using the same
fixings as the Outside Grille assembly. The base of the Terminal
incorporates a foam strip which is designed to adhere to the
glass surface assisng fing and also as a seal for the joint when
assembled together with the fan unit.
Glass
Main
Window
fan kit
Weather
Terminal
Spacer
Wall
Fixing
Plate
Interior
Grille
Outside
Grille
Fit the inside grille, locang it over the top lip before
engaging screws.
9
10
11
13
12
Screw the case/ grille assembly together.
For various wiring opons see page 5.
Release the electrical cover from the fan plate.
Assemble the fan plate to the case.
IMPORTANT
(Shuer Operaon XS fans)
There will be a short delay on start-up and shutdown of
approximately 40 seconds, this is normal.
4.2 Fing Ancillaries (Also see page 8)
4.2.1 Thin Wall Installaon
The diagram shows the unit
installed in a mber wall.
A Wall Fixing Plate is used
to support the fan assembly
and the installaon is similar
to that for a window.
4.2.2 Weather Terminal
The oponal Weather Terminal is offered for use in exposed site
condions.
The illustraon shows the Weather Terminal installed replacing the
Outside Grille assembly. Terminal is held in posion using the same
fixings as the Outside Grille assembly. The base of the Terminal
incorporates a foam strip which is designed to adhere to the
glass surface assisng fing and also as a seal for the joint when
assembled together with the fan unit.
Glass
Main
Window
fan kit
Weather
Terminal
Spacer
Wall
Fixing
Plate
Interior
Grille
Outside
Grille

LAB1350R May 2018 Page 4
V E N T I L A T I O N
Installation and Maintenance
DX Window Fan Kit 50Hz/60Hz
5.0 Electrical Installaon
Electrical work should be undertaken by a qualified electrician in accordance with the wiring regulaons.
1
2
3
4
Release the electrical panel from the fan plate.
Clamp the cable and complete the connecons.
Remove the terminal cover.
Refit terminal cover before replacing the electrical panel.
5.1 Wiring
5.1.1Fan Operated By On / Off Switch
5.1.2Fan Operated By Integral Sensor
5.1.3Basic Fan Operated By Remote Sensor
L5
L4
L3
L2
L1
N
or
L
N
Double pole
DX Fan unit
isolator
Fuse
max. 3 amp
Double pole
isolator
Fuse
max. 3 amp
L5
L4
L3
L2
L1
N
or
L
N
DX Fan unit with
integral sensor
SL
(Switched Live)
Double
pole
isolator max.
Fuse
3 amp
Remote sensor
L5
L4
L3
L2
L1
N
or
L
N
DX Fan unit
L1 L2 N
Connect link wire between L2 & L4 for extract OR
connect link wire between L2 & L3 for supply.
Connect link wire between L2 & L4 for extract OR
connect link wire between L2 & L3 for supply.
Connect link wire between L2 & L4 for extract OR
connect link wire between L2 & L3 for supply.
Connect switched live signal to L5 for integral mer module.
IMPORTANT
Isolaon - Before commencing work, make sure that the unit is
electrically isolated from the mains supply.
5.0 Electrical Installaon
Electrical work should be undertaken by a qualified electrician in
accordance with the wiring regulaons.
1
2
3
4
Release the electrical panel from the fan plate.
Clamp the cable and complete the connecons.
Remove the terminal cover.
Refit terminal cover before replacing the electrical panel.
5.1 Wiring
5.1.1Fan Operated By On / Off Switch
5.1.2Fan Operated By Integral Sensor
5.1.3Basic Fan Operated By Remote Sensor
L5
L4
L3
L2
L1
N
or
L
N
Double pole
DX Fan unit
isolator
Fuse
max. 3 amp
Double pole
isolator
Fuse
max. 3 amp
L5
L4
L3
L2
L1
N
or
L
N
DX Fan unit with
integral sensor
SL
(Switched Live)
Double
pole
isolator max.
Fuse
3 amp
Remote sensor
L5
L4
L3
L2
L1
N
or
L
N
DX Fan unit
L1 L2 N
Connect link wire between L2 & L4 for extract OR
connect link wire between L2 & L3 for supply.
Connect link wire between L2 & L4 for extract OR
connect link wire between L2 & L3 for supply.
Connect link wire between L2 & L4 for extract OR
connect link wire between L2 & L3 for supply.
Connect switched live signal to L5 for integral mer module.
IMPORTANT
Isolaon - Before commencing work, make sure that the unit is
electrically isolated from the mains supply.
5.0 Electrical Installaon
Electrical work should be undertaken by a qualified electrician in accordance with the wiring regulaons.
12
34
Release the electrical panel from the fan plate.
Clamp the cable and complete the connecons.
Remove the terminal cover.
Refit terminal cover before replacing the electrical panel.
5.1 Wiring
5.1.1Fan Operated By On / Off Switch
5.1.2Fan Operated By Integral Sensor
5.1.3Basic Fan Operated By Remote Sensor
L5
L4
L3
L2
L1
N
or
L
N
Double pole
DX Fan unit
isolator
Fuse
max. 3 amp
Double pole
isolator
Fuse
max. 3 amp
L5
L4
L3
L2
L1
N
or
L
N
DX Fan unit with
integral sensor
SL
(Switched Live)
Double
pole
isolator max.
Fuse
3 amp
Remote sensor
L5
L4
L3
L2
L1
N
or
L
N
DX Fan unit
L1 L2 N
Connect link wire between L2 & L4 for extract OR
connect link wire between L2 & L3 for supply.
Connect link wire between L2 & L4 for extract OR
connect link wire between L2 & L3 for supply.
Connect link wire between L2 & L4 for extract OR
connect link wire between L2 & L3 for supply.
Connect switched live signal to L5 for integral mer module.
IMPORTANT
Isolaon - Before commencing work, make sure that the unit is
electrically isolated from the mains supply.

LAB1350R May 2018 Page 5
V E N T I L A T I O N
Installation and Maintenance
DX Window Fan Kit 50Hz/60Hz
5.1.4 Supply / Extract Fan Operated via remote DX-CON Control
5.1.5Supply / Extract Fan Operated via remote DX-CON Control
5.1.6 Supply / Extract Fan Operated via remote DX-CON Control
Remote switch may be set: On/Off, Forward/Reverse, Economy/Std.
(variable speed), Auto/Manual.
Remote switch may be set: On/Off, Forward/Reverse, Economy/Std.
(variable speed), Auto/Manual.
One or more Remote Sensors may be wired in parallel to one DX-CON
Control.
Humidity Sensor: DX-HR
Air Quality Sensor: DX-AQR
Passive Infra-Red Sensor: DX-PIRR
Remote switch may be set: On/Off, Forward/Reverse, Economy/Std.
(variable speed), Auto/Manual.
Maximum one Integral Sensor per fan, 6/9/12 denotes unit size identy.
Humidity Sensor: DX-H6/9/12
Passive Infra Red Sensor: DX-PIR6/9/12
Run on Timer: DX-TA6/9/12.
A single sensor will switch all fans if more than one fan is being
operated by a single DX-CON controller.
NOTE: Mul-fan opons:
Up to 5 fans (size 6"/9") can be controlled by one DX-CON.
Up to 2 fans (size 12") can be controlled by one DX-CON.
Do not mix different fan sizes on the same controller.
DX-CON controller
L5
L4
L3
L2
L1
N
L4
L3
L2
L1
N
L1
N
Double
pole
isolator
Fuse
max.
3 amp
L
N
DX Fan unit
mains
supply
DX-CON controller
L5
L4
L3
L2
L1
N
L4
L3
L2
L1
N
L1
N
Double
pole
isolator max.
Fuse
3 amp
L
N
DX Fan unit
Remote sensor
mains
L2 L1 N
supply
DX-CON controller
L5
L4
L3
L2
L1
N
L4
L3
L2
L1
N
L1
N
Double
pole
isolator
Fuse
max.
3 amp
L
N
DX Fan unit with
integral sensor
Required if using
integral Timer
mains
supply
IMPORTANT
(Shuer Operaon DX fans)
There will be a short delay on startup and shutdown of
approximately 40 seconds. This is normal.
Model
Input Power
(W) Weight
(kg)
Max. Economy
DX6WW supply & extract 38 20 4.1
DX9WW supply & extract 50 37 5.7
DX12WW supply & extract 100 70 8.6
5.2 Unit Consumpon & Weight
5.3 Electrical Specificaon
230V ~ 50Hz / 220V ~ 60Hz Class I. Motor thermally protected by
overload device. Cable: 1mm max. or min. Fuse: 3 amp (if fan is supplied
from a 5A lighng circuit, no local fuse is required).
Note: If 2 x 12 inch fans or 5x 6 or 9 inch fans are used in the same
operang mode in the same room they should all be controlled from
the same CON speed control. This avoids the possibility of one fan (if
speed controlled at a lower flow rate) being stalled by the other fan(s).
Adequate make-up air provision sufficient to provide venlaon in
accordance with building regulaons is required in all rooms. This
should be checked during commissioning with all fans in the same room
running together in all possible configuraons.
The automac shuers, motor bearings should be frequently inspected
and maintained to ensure they open fully/operate sasfactorily. Use
of an RCD and fused spur with 1A, Bussmann TDC180, BS1362, fuse
(Farnell order no: 1123029) for 1 fan or 2A, Bussmann TDC180, BS1362
fuse (Farnell order no: 1123032) for 2 or 3 fans is recommended.
Always confirm airflow direcon before commissioning.
Note figures are for extract only at 50hz.
5.1.4 Supply / Extract Fan Operated via remote DX-CON Control
5.1.5Supply / Extract Fan Operated via remote DX-CON Control
Remote switch may be set: On/Off, Supply/ Extract, Economy/Std.
(variable speed), Auto/Manual.
Remote switch may be set: On/Off, Supply/ Extract, Economy/Std.
(variable speed), Auto/Manual.
One or more Remote Sensors may be wired in parallel to one DX-CON
Control.
Humidity Sensor: DX-RH
5.1.6 Supply / Extract Fan Operated via remote DX-CON Control
Remote switch may be set: On/Off, Supply/ Extract, Economy/Std.
(variable speed), Auto/Manual.
Maximum one Integral Sensor per fan, 6/9/12 denotes unit size identy.
Humidity Sensor: DX-H6/9/12
nfra Red Sensor: DX-PIR6/9/12
Passive I
Run on Timer: DX-T6/9/12.
A single sensor will switch all fans if mo
re than one fan is being
operated by a single DX-CON controller.
NOTE: Mul-fan opons:
Up to 5 fans (size 6"/9") can be controlled by one DX-CON.
Up to 2 fans (size 12") can be controlled by one DX-CON.
Do not mix different fan sizes on the same controller.
DX-CON controller
L5
L4
L3
L2
L1
N
L4
L3
L2
L1
N
L1
N
Double
pole
isolator
Fuse
max.
3 amp
L
N
DX Fan unit
mains
supply
DX-CON controller
L5
L4
L3
L2
L1
N
L4
L3
L2
L1
N
L1
N
Double
pole
isolator max.
Fuse
3 amp
L
N
DX Fan unit
Remote sensor
mains
L2 L1 N
supply
DX-CON controller
L5
L4
L3
L2
L1
N
L4
L3
L2
L1
N
L1
N
Double
pole
isolator
Fuse
max.
3 amp
L
N
DX Fan unit with
integral sensor
Required if using
integral Timer
mains
supply
IMPORTANT
(Shuer Operaon DX fans)
There will be a short delay on startup and shutdown of
approximately 40 seconds. This is normal.
Model
Input Power
(W) Weight
(kg)
Max. Economy
DX6WW supply & extract 38 20 4.1
DX9WW supply & extract 50 37 5.7
DX12WW supply & extract 100 70 8.6
5.2 Unit Consumpon & Weight
5.3 Electrical Specificaon
230V ~ 50Hz / 220V ~ 60Hz Class I. Motor thermally protected by
overload device. Cable: 1mm max. or min. Fuse: 3 amp (if fan is supplied
from a 5A lighng circuit, no local fuse is required).
Note: If 2 x 12 inch fans or 3 x 6 or 9 inch fans are used in the same
operang mode in the same room they should all be controlled from
the same CON speed control. This avoids the possibility of one fan (if
speed controlled at a lower flow rate) being stalled by the other fan(s).
Adequate make-up air provision sufficient to provide venlaon in
accordance with building regulaons is required in all rooms. This
should be checked during commissioning with all fans in the same room
running together in all possible configuraons.
The automac shuers, motor bearings should be frequently inspected
and maintained to ensure they open fully/operate sasfactorily. Use
of an RCD and fused spur with 1A, Bussmann TDC180, BS1362, fuse
(Farnell order no: 1123029) for 1 fan or 2A, Bussmann TDC180, BS1362
fuse (Farnell order no: 1123032) for 2 or 3 fans is recommended.
Always confirm airflow direcon before commissioning.
Note figures are for extract only at 50hz.

LAB1350R May 2018 Page 6
V E N T I L A T I O N
Installation and Maintenance
DX Window Fan Kit 50Hz/60Hz
Plug the connector into the required sensor module.
Screw the sensor module into posion.
1
2
4
3
5
6
7
Push the repacement cover into the grille front.
Lift out the sensor module wiring connector.
Push out the sensor area cover from the grille.
Remove the module plate.
Unscrew the module plate from motor plate assy.
5.4 Fing Integral Sensors (Oponal)
Note: Before following the pictorial sequence shown, first remove the
fans front cover grille (2 screws). Release the four main corner screws
and li out the motor/fan plate assembly. Remove the electrical cover
plate opposite the sensor plate. Follow the pictorial sequence on this
page.
Plug the connector into the required sensor module.
Screw the sensor module into posion.
1
2
4
3
5
6
7
Push the repacement cover into the grille front.
Lift out the sensor module wiring connector.
Push out the sensor area cover from the grille.
Remove the module plate.
Unscrew the module plate from motor plate assy.
5.4 Fing Integral Sensors (Oponal)
Note: Before following the pictorial sequence shown, first remove the
fans front cover grille (2 screws). Release the four main corner screws
and li out the motor/fan plate assembly. Remove the electrical cover
plate opposite the sensor plate. Follow the pictorial sequence on this
page.

LAB1350R May 2018 Page 7
V E N T I L A T I O N
Installation and Maintenance
DX Window Fan Kit 50Hz/60Hz
Fix backplate box to the prepared wall.
Feed approx. 200mm of supply cable into the box
1
2
4
3
5
6
7
Fit the control into the backplate box and secure.
Test the installaon.
Lift up panel and remove two screws to dismantle unit.
Spot through backplate box and drill and plug the wall.
Connect the end of the cable into the control block.
200mm
1.5m
Push out backplate box cable entry using a screwdriver.
5.5 Fing Remote Controller DX-CON or
Remote sensors (oponal)
The DX-CON Mul Fan Control provides supply or extract, variable
speed and automac or manual switching of several fans if desired, (see
note below). The control is best mounted approx 1.5m above the floor.
Remote Sensors are available for Humidity, Air Quality and Passive Infra
Red control. Remote Sensors should be posioned at least 1.5m above
the floor and away from direct heat sources e.g. radiators.
Note:
Up to 5 fans (size 6 / 9 inch) can be controlled by one DX-CON.
Up to 2 fans (size 12 inch) can be controlled by one DX-CON.
Do not mix different fan sizes on the same controller.
Fix backplate box to the prepared wall.
Feed approx. 200mm of supply cable into the box
1
2
4
3
5
6
7
Fit the control into the backplate box and secure.
Test the installaon.
Lift up panel and remove two screws to dismantle unit.
Spot through backplate box and drill and plug the wall.
Connect the end of the cable into the control block.
200mm
1.5m
Push out backplate box cable entry using a screwdriver.
5.5 Fing Remote Controller DX-CON or
Remote sensors (oponal)
The DX-CON Mul Fan Control provides supply or extract, variable
speed and automac or manual switching of several fans if desired, (see
note below). The control is best mounted approx 1.5m above the floor.
Remote Sensors are available for Humidity, Air Quality and Passive Infra
Red control. Remote Sensors should be posioned at least 1.5m above
the floor and away from direct heat sources e.g. radiators.
Note:
Up to 5 fans (size 6 / 9 inch) can be controlled byone DX-CON.
Up to 2 fans (size 12 inch) can be controlled byone DX-CON.
Do not mix different fan sizes on the same controller.

Page 8
V E N T I L A T I O N
Installation and Maintenance
DX Window Fan Kit 50Hz/60Hz
Glass
Main
Window
fan kit
Weather
Terminal
6.0 Ancillaries
Weather Terminal
Used for exposed site wall
installaons, comprising one
weather terminal, manufactured
from HIPS.
Order Code DX-WT6
Dimensions: 360 x 360 x 170mm
Order Code DX-WT9
Dimensions: 425 x 425 x 180mm
Order Code DX-WT12
Dimensions: 506 x 506 x 185mm
The Weather terminal unit replaces
the outside grille and is supplied
with installaon details.
Wall Fixing Plate
The Wall Fixing Plate is used for thin wall
and above ceiling applicaons, to support
the fan assembly.
7.0 Maintenance
Periodically, at least once a year or more frequently in case of heavy
use, remove the dirt and encrustaon from the grille(s) fan impeller
and motor casing. Ensure the impeller is not cracked or deformed and is
able to rotate freely and without oscillaon.
Do not use any solvents to clean this product.
8.0 Replacement Of Parts
As a manufacturer Domus is aware that me is important. In the event
of a breakdown of this equipment, it should be adequately packaged
and returned to Domus.
Please telephone Domus before posng your unit. A returns number will
be issued to idenfy your package.
We will endeavour to repair or replace it within five working days of
receipt. See our warranty terms.
Technical or commercial consideraons may,from me to me, make it necessary to alter the design, performance and dimensions of equipment
and the right is reserved to make such changes without prior noce.
9.0 Warranty
The 2year warranty starts from the day of deli very and includes parts
and labour for the first year. The remaining period covers replacement
parts only.
This warranty is void if the equipment is modified without
authorisaon, is incorrectly applied, misused, disassembled, or not
installed, commissioned and maintained in accordance with the details
contained in this manual and general good pracce.
The product warranty applies to the UK mainland and in accordance
with Clause 14 of our Condions of Sale.
Customers purchasing from outside of the UK should contact Domus
Internaonal Sales office for further details. A unit returned to Domus
should be suitably protecvely packaged and clearly marked with the
‘returns number’ obtained from Domus prior to posng.
10.0 Aer Sales Enquiries
For technical assistance or further product informaon, including spare
parts and replacement components, please contact the Aer Sales
Department.
LAB1349R, Issue 1, Apr 2018 Page 8
VE N T I L A T I O N
Domus Ventilation
Block C
Caerphilly Business Park
V an Road
Caerphilly
CF83 3ED
T el: [phone]
Fax: [phone]
Email: [email protected]
www.domusventilation.co.uk
LAB1350R May 2018
The EMC Directive
2014/30/EU
The Low Voltage
Directive
2014/35/EU