DoorKing 900 MHz RF User manual

900 MHz WIRELESS RF REMOTE MODULE
DoorKing Part Number
1470-080
Installation
Note: DoorKing offers a 900 MHz
Wireless Test Range Kit (P/N XXXX-XXX)
to allow easy testing of the wireless
signal between 2 devices at chosen
locations BEFORE installing the devices.
The self-powered test kit measures the
900 MHz wireless signal between 2
devices in ANY chosen locations.
Ensuring a good signal can be achieved
before installation occurs.
Antenna Options
RF
SECURE
34
33
32
31
30
29
28
27
26
25
24
23
22
21
14
15
16
17
18
19
20
13
12
11
10
9
8
7
6
5
4
3
2
1
1
0
BOARD ADDRESS
NC
WEIG TRUE
RELA
Y
NO
NC
ALARM
RELAY
NO
NC
MONITOR
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF
ST
A
TUS
CODE
SENT
CODE
GOOD
CODE
BAD
0
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
ON
PROGRAM
NET ID CH
POWER
RF
STRENGTH
TXD
RXD
1470-010
0
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
0
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
0
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
SX1276
Input:
120 V 60 Hz
Output:
16.5 VAC 20 VA
2358-010 Tracker
Expansion Board
1470 Wireless
RF Remote Module
Power
Transformer
Connect to terminals
#33 & #34.
Wireless
Programming
See back
Note: See “HARDwired Tracker
Expansion Board Installation
manual” 2358-065 for complete
wiring of the tracker expansion board.
4 Screws to secure
1470 board to tracker
expansion board.
Same NET ID numbers
and Same CH numbers
MUST be set so the
wireless devices can
communicate with each
other.
Press
after
making
changes
to NET ID
and CH.
Range testing is HIGHLY
recommended before
FINAL installation.
Plug the 1470 wireless RF remote module into the wireless connector and secure boards with 4 screws to the 2358 tracker expansion board.
See the HARDwired tracker expansion board manual 2358-065 to connect desired options to tracker board terminals #1- #34 to manage a remote
access point. DO NOT CONNECT ANY WIRES TO TERMINALS #10, #17, #27, #28 or #29 (Used for HARDwire communication line ONLY). Power
transformer must connect to tracker expansion board #33 and #34 (REQUIRED). Antenna is REQUIRED.
This 900 MHz wireless RF remote module provides wireless communication for a 2358-010 tracker expansion board to a 900 MHz wireless
baseboard in a access control system. Use this 900 MHz wireless boards ONLY with DoorKing: 1833, 1835, 1837 and 1838 multi-door access
controller access control systems. DO NOT use with 1838 Access Plus model.
Antenna
Connection
See above
Externally Mounted
900 MHz Antenna Kit
P/N 1514-079
13 ft
of cable out of
bottom of cabinet
Range is Up to 1000 ft
direct-line-of-sight.
Range is Up to 1000 ft
direct-line-of-sight.
Cabinet Mounted
900 MHz Antenna Kit
P/N 1514-019
900 MHZ Wireless
Dual Band Repeater
P/N 2332-080
Range is Up to 1000 ft
direct-line-of-sight.
See instruction sheet for
more information.
900 MHz
Short Range
Cabinet Mounted
Antenna (Supplied)
Range is Up to 200 ft
direct-line-of-sight.
Range WILL VARY
GREATLY depending on
individual setup: Antenna
height above the ground,
background signal
interference, physical
obstructions (trees,
buildings etc.). Adverse
weather (rain) CAN also
affect antenna range. Single Board Enclosure with
Built-In Card Reader and Lighting
DK Prox Reader - P/N 1815-333
HID Reader - P/N 1815-392
AWID Reader - P/N 1815-292
Single Board
Enclosure
P/N 2351-080
900 MHz Wireless
Enclosure Options
Antenna
Mount
Antenna Mount
0
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
0
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
0
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
NET ID CH
PROGRAM
RF Strength -
ONLY used for technican
troubleshooting.
TXD - Blinks during
wireless communication.
RXD - Blinks during
wireless communication.
1470-065 Issued 11-18
Version B

120 S. Glasgow Avenue
Inglewood, California 90301 U.S.A.
Copyright 2018DoorKing®, Inc. All rights reserved.
Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be
totally lost. Although significant delays or losses of data are rare when wireless devices are used in a normal manner with a well-constructed network, DoorKing
wireless products should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party,
including but not limited to personal injury, death, or loss of property. DoorKing, Inc. accepts no responsibility for damages of any kind resulting from delays or
errors in data transmitted or received using DoorKing wireless products, or for failure of DoorKing wireless products to transmit or receive such data.
Do not operate DoorKing wireless products in areas where cellular modems are not advised without proper device certifications. These areas include environments
where cellular radio can interfere such as explosive atmospheres, medical equipment, or any other equipment which may be susceptible to any form of radio
interference. DoorKing wireless products can transmit signals that could interfere with this equipment. Do not operate DoorKing wireless products in any aircraft,
whether the aircraft is on the ground or in flight. In aircraft, DoorKing wireless products MUST BE POWERED OFF. When
operating, DoorKing wireless products can transmit signals that could interfere with various onboard systems.
The driver or operator of any vehicle should not operate DoorKing wireless products while in control of a moving vehicle.
Doing so will detract from the driver or operator’s control and operation of that vehicle. In some states and provinces,
operating such communications devices while in control of a vehicle is an offence.
DoorKing Part Number
1470-080
Important Notice
Safety and Hazards
Program
Step
Factory
Default
Description Options
Selection
Number Function
Wireless RF Remote Module Tracker Expansion Board Programming ONLY
See the 900 MHz Wireless Baseboard manual 2333-065
and Tracker Expansion Board manual 2358-065
for ALL tracker expansion board programming and wiring.
LED Display
Sets all parameters to Factory Default
Displays current signal strength between Baseboard and Tracker.
• 80 or lower - GOOD.
• 80-85 - Unreliable signal strength.
• 86-99 - NO signal.
Sets Wireless Tracker to act as Repeater
Do Not Change. Contact DoorKing tech support.
Repeater Mode OFF
Repeater Mode ON
Adding relay control delay to Trackers using the same Zone Addresses
If more than one tracker board is set to the same address (zone addresses), then
change this value to a unique number. Only program this for tracker boards with the
same addresses. Start out with a value of 1 then increase the next board to 2, then
the 3rd board to 3 etc... This will prioritize the relay access order of the same zone
address boards.
View the number of lost communication transactions with the base.
Use the arrows buttons to change the value.
Preset at Factory. Do Not Change. Contact DoorKing tech support.
This value is set to 2. No need to adjust.
Preset at Factory. Do Not Change. Contact DoorKing tech support.
Period Tracker board checks in with 1835 for schedule hold open (minutes).
Preset at Factory. Do Not Change. Contact DoorKing tech support.
Low Byte Value MAC address used only for 900MHz. Assigned during manufacturing.
When wireless communication is lost with the base for “X” number of minutes
defined in step 17, this step will instruct the tracker board what action to take.
Does nothing
Counts the number of lost communication transactions
Reboot the RF module only
Set RF module with net ID and channel selected
Initialize RF module then reboot RF remote module
Restore programming value, sets RF remote module net ID and CH, then reboots RF
module address boards.
E1 - Relay connected to 4-pin terminal pins 1 & 2 is on for more than 5 seconds. Relay 1 in 1830 should be set for 00 seconds (0.25 second strike time)
E2 - Relay connected to 4-pin terminal pins 3 & 4 is on for more than 5 seconds. Relay 2 in 1830 should be set for 00 seconds (0.25 second strike time)
A1 - Board address is invalid for Tracker. Board address is improperly set as 0, 1, 2 or 19.
A2 - Dual Mode - Bad Address, 18or 19 not allowed.
Error codes on LED Displays for Baseboard and Tracker Board
View RF Signal Strength
Reset to Factory Defaults
Low Byte MAC
1835 Checkin Time (Factory Set)
Card Code Forwarding
(Factory Set) 0 or 1 0
1
5
5
2
0
1
2
3
4
5
0:
Off
5
Minutes
5
0
0
2
22
Same Zone Address
Relay Delay
Lost Wireless Communication
Options
(Factory Set)
View the Number of Lost
Wireless Communications
Air Busy Wait Time
(Factory Set)
23
24
25
26
21
17
18
19
AdjustableView RF POT Setting
20
0 - 20
1 - 5
1 - 99
5
0 - 5
0 - 99
0 - 20
1:
counts the
number of
lost com
trans.
Sets maximum amount of allowable signal strength loss
1. Press a button to activate LED display.
2. Press ENT button and then use scroll buttons to display desired “Program Step” number from list below.
3. Press ENT button to enter selected program step number.
4. Select desired data while in program step using buttons.
5. Press ENT button to enter selected data.
6. Press ENT button AGAIN to EXIT programming OR after 10 seconds, board will automatically EXIT programming.
1470-065 Issued 11-18
Version B