Dorel Living BELMONT DA1026P-18 User manual

DA1026W-18
DA1026B-18
DA1026P-18
DA1026WN-18 0-72000-96501-6
0-65857-15766-6
0-72000-96502-3
0-65857-14462-8 WHITE
BLACK
PINE
WALNUT
BELMONT BUNK BED

BELMONT BUNK BED
DA1026P-18 PINE / DA1026W-18 WHITE / DA1026WN-18 WALNUT / DA1026B-18 BLACK
JOINT CONNECTOR (4mm HEX HEAD)
1/4" x 85mm
16 PCS
6.5mm x 48mm
WOOD JOINT CONNECTOR (4mm HEX HEAD)
6.5mm x 100mm
16 PCS
BARREL NUT
11.8mm x 15mm
16 PCS
FLAT HEAD SCREW
4mm x 35mm
32 PCS
FLAT HEAD SCREW
4mm x 30mm
6 PCS
WOOD DOWEL
10mm x 50mm
28 PCS
1
HARDWARE LIST
34
2
WOOD JOINT CONNECTOR (4mm HEX HEAD)
12 PCS
56
79
10 11
WOOD DOWEL
15mm x 60mm
4 PCS
WOOD JOINT CONNECTOR (4mm HEX HEAD)
6.5mm x 80mm
6 PCS
STOPPER
4 PCS
HEX KEY
1 PC
1

BELMONT BUNK BED
DA1026P-18 PINE / DA1026W-18 WHITE / DA1026WN-18 WALNUT / DA1026B-18 BLACK
A
A
B
C
D
D
E
F
F
G
G
H
J
K
L
M
N
LL
R
R
S
S
T
T
AB
PARTS LIST
C
DEF
TOP POST
2 PCS
BOTTOM POST
2 PCS HEADBOARD TOP CROSS
4 PCS
TOP POST
1 PC TOP POST 1 PC
BOTTOM POST
2 PCS
2

BELMONT BUNK BED
DA1026P-18 PINE / DA1026W-18 WHITE / DA1026WN-18 WALNUT / DA1026B-18 BLACK
3

NOTES: Headboard top cross (F) and headboard bottom cross (G) may require that they be pulled
closer together or further apart in order to allow wood dowels (7) to align with holes in top posts (A
and B).
Insert stoppers (8) and headboard slats (S) into the holes of the headboard bottom cross (G) and
push down until firmly in place. Slide the headboard top cross (F) onto the headboard slats (S). Insert
wood dowels (7) into ends of top cross (F) and bottom cross (G). Attach top posts (A & B) using wood
joint connectors (3) as shown.
BELMONT BUNK BED
DA1026P-18 PINE / DA1026W-18 WHITE / DA1026WN-18 WALNUT / DA1026B-18 BLACK
One of the headboard top cross (F) has a label on it, do not use it in this step.
STEP 1
F
S
7
3
A
8
7
B
A
S
F
G
88 PCS
4 PCS
74 PCS
3
without label
4

NOTE: Headboard top cross (F) and headboard bottom cross (G) may require that they are pulled
closer together or further apart in order to allow wood dowels (7) to align with holes in top posts (A
and C).
Insert stoppers (8) and headboard slats (S) into the holes of the headboard bottom cross (G) and
push down until firmly in place. Slide the headboard top cross (F) onto the headboard slats (S). Insert
wood dowels (7) into ends of top cross (F) and bottom cross (G). Attach top posts (A & C) using wood
joint connectors (3) as shown
BELMONT BUNK BED
DA1026P-18 PINE / DA1026W-18 WHITE / DA1026WN-18 WALNUT / DA1026B-18 BLACK
Use the headboard top cross with label (F) in this step.
STEP 2
F
S
7
3
A
8
7
C
A
S
F
G
88 PCS
4 PCS
74 PCS
3
with label
5

STEP 3
BELMONT BUNK BED
DA1026P-18 PINE / DA1026W-18 WHITE / DA1026WN-18 WALNUT / DA1026B-18 BLACK
Insert stoppers (8) and headboard slats (S) into each hole in the headboard bottom cross (G) and push
them down until firmly in place. Slide headboard top cross (F) onto headboard slats (S). Insert wood dowels
(7) into ends of top cross (F) and bottom cross (G). Attach bottom posts (D and E) using wood joint
connectors (3) as shown.
Repeat the above step to assemble the remaining headboard.
816 PCS 78 PCS
8 PCS
3
6

BELMONT BUNK BED
DA1026P-18 PINE / DA1026W-18 WHITE / DA1026WN-18 WALNUT / DA1026B-18 BLACK
Attach the two headboards with the bottom posts (D and E) to the bottom side rails (I and K) by the
joint connectors (1) and barrel nuts (9) as shown. Use hex key (10) to tighten joint connectors.
STEP 4
This is the lower bunk.
7

STEP 5
BELMONT BUNK BED
DA1026P-18 PINE / DA1026W-18 WHITE / DA1026WN-18 WALNUT / DA1026B-18 BLACK
Insert a wood dowel (7) into each end of the long guardrails (M). Attach the two long guardrails
(M) and the two top side rails (H and J) to the top posts (A and B) and (A and C) as shown. Use
the joint connectors (1) with the barrel nuts (9) to fasten the top side rails (H and J) and use the
wood joint connectors (11) to fasten the long guardrails (M). Use hex key (10) to tighten joint
connectors.
8