Dormakaba SLAN-DR User manual

WN 059730 45532 – 2018-11
EN
SLAN-DR
Mounting instructions
Contents
1 About this document 1
2 Safety 1
3 Product description 1
4 Mounting 2
5 Disassembly and disposal 3
1 About this document
1.1 Contents and purpose
This document describes the mounting of the SLAN-
DR network adapter (SafeRoute® Local Area Network
for DIN rail mounting).
1.2 Target group
This document is intended for assembling technicians
and specialists authorized for mounting by
dormakaba.
1.3 Other applicable documents
• Instructions for devices intended for networking
1.4 Symbols used
Components may be damaged by
electrostatic discharge. Ground
your own body before touching a
component!
2 Safety
2.1 Intended use
With the help of SLAN-DR network adapters,
dormakaba control modules intended for networking
are networked in one building.
2.2 Personnel qualification
Mounting may only be carried out by persons
authorized by dormakaba.
3 Product description
The SLAN-DR network adapter enables the
integration of dormakaba control modules into LAN
networks. The mounting takes place on a 35 mm DIN
rail in a housing. The housing must at least meet the
requirements of IP 30.
The control, parameterization and visualization for
the connected devices is carried out on a PC with TMS
Soft®.
3.1 Parts included
106
92
63

2SLAN-DR 2018-11
WN 059730 45532
dormakaba Mounting instructions MountingMounting
3.2 Technical information
Supply voltage: 24VDC +/- 15 %
Power consumption: 60 mA
Ambient temperature: -10 °C to +55 °C
Rel. humidity: up to 93 %
(non condensing)
Protection class: Dependent on the
housing used
Ethernet 10Base-T or 100Base-Tx
Segment length max. 100 m
Cable recommendation at least CAT5 cable
3.3 LED display
The LED displays light up yellow and green.
LED on LED off
Link LED
10 MBit/s yellow
100 MBit/s green
No connection
Activity LED
Half duplex yellow
Full duplex green
No activity
4 Mounting
The mounting takes place by clipping onto a 35 mm
DIN rail.
4.1 Installation requirement
Prerequisite for the mounting is compliance with the
LAN specifications regarding transceivers, network
topology, network lengths, cable specifications, etc.
• The mounting location of the modules must be
selected so that the modules’ ambient temperature
range is maintained and any heat generated can be
dissipated.
• A minimum distance of 200 mm to high-energy
sources of interference, e.g. frequency converters, is
recommended.
• To avoid condensation, modules that have been
stored at very different temperatures must be
adjusted to the operating temperature before
commissioning.
4.2 Assignment of terminals
24V
GND
TxD1
TxD2
GND
TxD3 RxD3
GND
RxD2
RxD1
GND
24V
X1
X3
Mac-Adresse
xx-xx-xx-xx-xx-xx
Activity
LED
Link
LED

3SLAN-DR 2018-11WN 059730 45532
dormakaba Mounting instructions MountingMounting
X1 24V24V
GND GND
TxD2 RxD2
TxD1 RxD1
GNDGND
TxD3 RxD3
stabilized power supply, input
TxD1
RxD1
RS232 port, e.g. dormakaba control module (max. 15m)
without function
without function
without function
without function
X3 without function
SLAN-DR connection example
24V
GND
TxD1
TxD2
GND
TxD3 RxD3
GND
RxD2
RxD1
GND
24V
X1
24VDC
GND
TxD
RxD
SLAN-DR
dormakaba control
module
5 Disassembly and disposal
Disassembly is carried out in the reverse order of
mounting and must be carried out by qualified
personnel.
The product must be disposed of in an
environmentally friendly manner. Electro-
technical parts and batteries must not be
disposed of as domestic waste. Dispose of
electrotechnical parts and batteries in the designated
acceptance and collection points. Refer to the
statutory regulations for your country.

dormakaba Deutschland GmbH
DORMA Platz 1 58256 Ennepetal Germany T: [phone] F: [phone] www.dormakaba.com
Translation of the original document, subject to change without notice