dotRed Audio Designs WORKFRAME 84 User manual

Owner’s Manual
© 2016 dotRed Audio Designs Co., Ltd.
Rev. E01
Thank you very much for choosing a dotRed product.
We hope that this unit will bring you countless hours of fun.
Keep this owner’s manual handy for future reference.
The latest version of this manual is available for free
download (PDF) on our website.

AC adaptor AC adaptor cord
Owner’s Manual (this document)
M3 x 8-type screws
for fixing modules (30pcs)
Square nuts
for fixing modules (30pcs)
Make sure that the package contains the main unit and
all the included items listed below.
INCLUDED ITEMS
Owner’s Manual
© 2016 dotRed Audio Designs Co., Ltd.
Rev. Exx

PRECAUTIONS FOR USE
！CAUTION
●Do not use any +5volt power adaptor, as our bus board already
provides a +5volt source. Connecting such a power adaptor would
damage the POWER BASE of this unit.
●If you wish to install a module fitted with a 10-pin connector, use a
10 pin to 16 pin Eurorack power cable.
●In compliance with the Eurorack standard, the 16-pin headers on this
unit have -12V assigned to their #1 pin. Prior to making any
connection, make sure that each module you intend to use with this
unit has the same pin assignment.
●Do not attempt to remove the dotRed logo bolted onto the
red logo plate as it has sharp edges and could cause injury.
●Use this unit exclusively indoors, making sure the environment of use
has an ambient temperature between 0ºC and 35ºC, and a relative
humidity below 85%.
Use this product by following all safety precautions in this owner's manual.
This product has a circuit protection feature intended to protect the
unit in case of overvoltage and short-circuit under normal conditions
of use as described in this manual.
However, due to several factors, we cannot guarantee that this
feature will effectively protect the unit in all cases.
●To avoid damaging the unit and guarantee a safe use, use exclusively
the supplied AC adaptor.

SAFETY PRECAUTIONS
Heed all precautions for your own safety!
！CAUTION
！WARNING
Keep this unit as well as its AC adaptor away from rain and any
damp/wet environment. If any liquid get splashed onto or gets
inside this unit or its AC adaptor, this can cause a malfunction
and poses a risk of electric shock.
If this unit shows any signs of abnormal behavior such as the
symptoms listed below, immediately disconnect the AC adaptor
from the mains and get in touch with the dealer where you
bought this unit:
・Smoke, sparks or a strange smell come out of this unit or its
AC adaptor.
・Some or all of the POWER BASEʼs status indicators are
blinking or off.
・The AC adaptor's cord is cracked or shows any other signs of
damage.
・The AC adaptor's body is damaged and fails to deliver
stable power.
Do not do any modification to this unit as it will void our
warranty and also poses a risk to your safety.

NAME & FUNCTION OF EACH COMPONENT
Ａ
Ｂ1
Ｂ４Ｂ５
Ｂ６
Ｂ2Ｂ３
Ｃ
Ｇ
Ｄ
Ｅ
Ｆ
}
ＡLogo plate:
This plate can be removed if you need to fit
one more module, and can also be moved to
another position to cover an empty slot.
ＤDC15V input:
Connect the AC adaptor's DC cable
end plug here.
ＧHeaders:
These fourteen 16-pin headers deliver
power to your modules.
Note: The #1pin of each header is -12Volt.
When connecting a module fitted with
less than 16 pins, make sure to connect
the module's plug's #1 pin to the #1 pin
on the header.
ＥPower switch:
Flip it to the "ON" position to power
on the unit.
ＦStatus indicators:
Indicate the power supply status.
Those indicators are lit under normal
power supply conditions.
ＢNut holes:
Allow you to easily add/remove square nuts
without removing a side plate.
ＣCable hook:
Pass the AC adaptor's DC cable through this
hook to prevent accidental disconnection.

MODULE INSTALLATION
１．
Insert a square nut into the rail via
one of its nut holes.
４．
Slightly tighten both screws so as
to be able to slide the module in
place onto the mounting rails.
５．
Slide the module to the desired
location and firmly tighten both
screws to fix the module, making
sure it is straight.
６．① Connect the AC adaptor's DC
cable end plug to the DC 15V
input.
②Pass the AC adaptor's DC
cable through the cable hook
for a secure connection.
③ Turn on the power by flipping
the power switch to the "ON"
position.
２．
Using the tip of a pen, slide the
square nut inside the mounting
rail to the approximate installation
position for the module.
Repeat the procedure to insert and
slide a square nut in place onto the
other mounting rail. Make sure
both square nuts are aligned
vertically.
３．
Connect the module's cable to the
desired header on the unit, then
align the mounting holes on the
module with the square nuts on
the mounting rails.
If needed, adjust the square nuts'
position.
①
②
③
Note: Lay the unit flat on its back panel on a stable surface for easier installation.
Place a clean, soft cloth under the unit to avoid scratches, accidental movement, etc.
Note: To remove an unused or damaged square nut, simply slide it with the tip of a pen
until it is flush with one of the square nut holes, then let the nut through the hole.

FEATURES
◆Ideal-size case for new Eurorackers or users
wishing to expand their existing system.
◆Rugged full-metal chassis offering effective
protection from noise and shocks.
◆30-watt power module optimized for 84HP case
size and power needs. The power module's design
prevents power line noise while ensuring lower heat
under full-load condition.
◆The power circuit's audio-optimized capacitors
ensure superior sound quality.
◆Allows connection of up to 14 modules
(subject to the power consumption and/or
dimensions of the modules).
◆19-inch rack compatible through optional rack
mount ears.
◆Economical, hassle-free square nuts.
◆Nut holes allow quick replacement of damaged/
worn nuts, and quick module relocation.
◆Sleek design offering enough installation depth for
most modules.

SPECIFICATIONS
◆Case format:
Euro-rack (Doepfer's A-100 format), 84HP
◆Power Specs
AC adaptor
・AC input ：100V～240V AC / 50～60Hz
・DC output：15V / 3.34A（2.5A min.）
・DC plug type: Outside Φ: 5.5mm
Inside Φ: 2.1mm
Polarity: center +
"POWER BASE" power module
・DC input: 15V (less than 18V)
・DC output current: 1000mA@+12V
1000mA@-12V
500mA@+5V
◆Dimensions (H x W x D): 132 x 430 x 90 mm
Note: W=480mm with optional rack-mount ears installed.
◆Weight: Approx. 1.6kg
Note: Approx. 2kg with optional rack-mount ears installed.

M3 x 8 screws: 30pcs
Square nuts: 30pcs
◆"RACK-EAR"
Brackets (pair) for 19-inch rack mount
◆"NUTS'n BOLTS"
Screws and Square nuts for module installation
OPTIONAL PARTS (available separately)

BEFORE USING THIS UNIT
●Before using this unit, install your modules refering
to the "MODULE INSTALLATION" section in this manual.
●To install our optional rack-mount ears on this unit,
refer to the owner's manual supplied with the dotRed
rack-ear brackets.
ENVIRONMENT OF USE & CLEANING
Read this section prior to using this unit.
◆Avoid exposure to moisture and direct sunlight.
Make sure to use this unit within an ambient
temperature between 0ºC to 35ºC and with a
relative humidity of <85%.
◆The supplied AC adaptor is exclusively designed for
indoor use. Never use it outdoors, as its safe and
correct operation cannot be guaranteed.
◆Use only this product outdoors in a proper and
electrically safe performance environment.
(such as on a festival stage, etc.)
◆Use this unit on a stable surface or installed on a
rack with rack-mount screws.
◆Use only a clean soft cloth if you need to clean this
unit. Do not use any solvent-based cleaning agents
as this may damage the unit's finish.
To remove stubborn dirt, slighlty damp a soft cloth
with water.

1-YEAR LIMITED WARRANTY
LIMITED WARRANTY TERMS AND CONDITIONS
This Limited Warranty applies only to DOTRED AUDIO DESIGNS products purchased in the
United States of America. Outside the USA, warranty policy and service is determined by the
laws of the country of purchase and followed by our local authorized distributor. A listing of
our authorized distributors is available at http://www.dotred-audio-designs.com/shops
DOTRED AUDIO DESIGNS warrants to the first owner of a covered product purchased from an
authorized DOTRED AUDIO DESIGNS dealer in the U.S., that this product will be free from
defects in materials and/or workmanship for a period of one year from the date of purchase.
Please register this product by sending us an email at [email protected]
to establish the date of purchase (THIS IS NOT A REQUIREMENT FOR WARRANTY SERVICE BUT
HIGHLY ADVISED). Besides your full name and address, please mention the date and purchase
location of your product.
To exercise your rights under this Warranty as the first owner/purchaser, YOU MUST SHIP THIS
PRODUCT IN ITS ORIGINAL PACKAGING at your expense, with proof of purchase documentation
and the DOTRED AUDIO DESIGNS supplied power adapter, to DOTRED AUDIO DESIGNS to the
following address:
DOTRED AUDIO DESIGNS CO., LTD
9-10 Kamijima, Hamakita-ku
Hamamatsu
434-0011 JAPAN
An RAN (Return Authorization Number) from DOTRED AUDIO DESIGNS must be obtained first
before returning any product.
Email us your RAN request to [email protected]
Products shipped to DOTRED AUDIO DESIGNS without an RAN will be refused and returned.
Shipping insurance is optional, but highly recommended. DOTRED AUDIO DESIGNS will repair
or replace this product at its sole option and at no charge to you for parts and labor—when
deemed necessary and within the warranty period—provided that DOTRED AUDIO DESIGNS
reserves the right to determine whether the product is “defective” for purposes of this Limited
Warranty. This Warranty does not apply if damage to this product occurs as a result of abuse or
misuse, failure to follow instructions according to its Owner’s Manual, abnormal use or
handling, improper packaging, another product’s interaction, exposure to temperature
extremes, or if the product has been altered or modified/ customized in any way, or the
damage was caused by unauthorized repair or service. The original product must return to
DOTRED AUDIO DESIGNS unaltered.
IN NO EVENT SHALL DOTRED AUDIO DESIGNS CO., LTD BE LIABLE FOR ANY INDIRECT,
INCIDENTAL, COLLATERAL, EXEMPLARY, PUNITIVE, CONSEQUENTIAL OR SPECIAL DAMAGES OR
LOSSES ARISING OUT OF YOUR PURCHASE OF PRODUCTS AND/OR OUT OF THIS WARRANTY,
INCLUDING WITHOUT LIMITATION, LOSS OF USE, PROFITS, GOODWILL OR SAVINGS OR LOSS
OF DATA, MUSIC, ELECTRONIC FILES, OR PREFERENCES THAT MAY HAVE BEEN STORED BY A
USER OF THE PRODUCT, EVEN IF DOTRED AUDIO DESIGNS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES OR CLAIMS. SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF INCIDENTAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
This Limited Warranty and the right of replacement is in lieu of any and all other warranties—
which you hereby waive—and it gives U.S. purchasers specific legal rights. You may also have
other rights which vary from State to State.
dotRed Audio Designs - 2016

TROUBLESHOOTING
If this unit does not seem to work properly and shows some of
the symptoms described here below, make sure each installed
module works correctly before sending the unit in for repair.
Symptoms
Causes
- One of the modules installed in the unit does not work properly.
- The current fed to the modules is overloading.
- One module's cable is shorted.
- One module's connector is not connected properly to the header.
- The AC adaptor doesn't work properly.
- When powering on the unit, the status indicators do not light up.
If the trouble cannot be solved by removing modules, and you
determine that this unit needs repair, contact the store where
you bought the unit, or write to us at:
[email protected].
Write down a short description of the problem and the
conditions when it first occurred.
- When powering on the unit, the status indicators’ luminosity is
lower than usual.

WARRANTY CARD
Model：WORKFRAME 84
Warranty term:
1 year
◆Keep this warranty card together with your receipt or sales slip as a proof of
the purchase location and date will be requestedfor any warranty claim.
Purchase date:
Address:
Customer
Shop or seller’s signature:
Name:
9-10, Kamijima, Hamakita-ku,
Hamamatsu 434-0011 JAPAN
Copy in this frame the 6-digit
serial number found on the label
inside the unit.
dotRed Audio Designs Co., Ltd.
If you have any question, please email us at: [email protected]
You can also get in touch and send us any query through the Contact page of
our website, or through our Facebook/Twitter page.
http://www.dotred-audio-designs.com
https://www.facebook.com/dotRedAudioDesigns
https://twitter.com/DotredAudio