DOTS IAMEP2001 User manual
USER GUIDE
DOTS by i.am+ Bluetooth Headphones IAMEP2001
Visit PULS.com for support.
English User guide
Warning letter:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
1. +
Button
2.
•
Power On
0
忏/
Pairing / Function
Button
3. -
Button
4. LED
indicator
5 Micro
USB(only for charging)
6
USB
door
7
Mi
c
r
op
hon
e
2
3
7
5
6
What’s in the Box.
l
DOTS by i.am+ Bluetooth Headphones
l
Micro USB charging cable.
l
Quick Start Guide
l
User Guide
l
Warranty
Headphonesoperation
Item Requirement and Description
Power On/Off
l
PowerOn:PressandholdtheFunctionbuttonfor3seconds.(releasethe
buttonaftertheblueLEDbright,theredLEDandblueLEDstartflashingmeans
thedeviceenterpairingmode)
l
PowerOff:PressandholdtheFunctionbuttonuntiltheredLEDlightup.Red
LEDturnoffmeansthedevicepoweroff
Pairing
l
First paring: Press and hold Function button for 3 sec. to power on, earphones
auto-enter pairing mode - LED alternates flashing Red and White.
l
To paring with your PULS or phone, go to settings on your PULS or phone,
make sure Bluetooth is switched on.
l
The ear-phones appears as “DOTS by i.am+” Select to pair.
l
Bluetooth pairing after a successful first pairing:
n
Power off then Press and hold Function button for 5 sec. to place earphones
in pairing mode - LED alternates flashing Red and White, mobile phone
search the Bluetooth device to connect the headphones (headphones ID is
“ DOTS by i.am+ ”
n
If the earphones are outside Bluetooth range and disconnect from PULS or
your phone, the headphones will automatically try to re-connect. If
reconnection is unsuccessful for more than 5 mins, the headset will power
off.
l
Set up use of DOTS headphones with multiple devices such as your PULS and
your smartphone.
1. Pair headphones to PULS or phone 1
2. Turn off the Bluetooth on PULS phone 1, and turn on Bluetooth on
phone 2
3. Search and pair the headset to phone 2
4. Turn on Bluetooth on PULS phone 1 and connect to headset
Charging Open USB door “6” on controller and connect micro USB cable “5”
The headset will power off then enter charging mode - LED signal red while
charging
Solid white when full charge is reached
Using
Headphones
with Aneeda
voice
assistant
Use the Aneeda button on your PULS device to speak to and hear Aneeda on your
headphones
LED
Indication
l
LED turned off when headset powered off or not charging
l
Power on: white LED on 1s
l
Power off: red LED on 1s
l
Pairing: LED alternates flashing Red and White
l
Connected: white LED 0.1s on/4s off
l
Disconnected: white LED 0.1s on 2 times/2s off
l
Incoming call: white LED 0.5s on /0.5s off
l
Outgoing call: white LED 0.5s on /0.5s off
l
Active call: white LED 1s on /1s off
l
Music play: white LED 1s on /4s off
l
LED is changed from white blinking to Red blinking when battery low
l
Charging：The headset will power off and enter charging mode - LED signal red
while charging, Solid white when full charge is reached.
Music Mode Function Status Sound
indication Operation
Volume up Music or phone
call mode No Press volume +
Volume
down Music or phone
call mode No Press volume -
Play/Pause Music mode No Short press Function button
Next song Music mode No Double press Function button
Previous
song Music mode No -
Phone call
mode Answer call Incoming call ‘Beep’ sound
once Press Function button 1 time
Reject
incoming call Incoming call No Press and hold Function button
for 2 seconds
Hang up
phone call During phone
call ‘Beep’ sound
one time Press Function button 1 time
Switch call
between
headset and
phone
During phone
call No Double press Function button
Mute During phone
call ‘Beep’ sound
two times Fast press volume down button
for 2 times
Cancel Mute During phone
call No Fast press volume up button for
2 times
l
Incoming call status:
n
When mobile phone connected to headset through Bluetooth, mobile phone
will stop music player and play ring tone when have incoming call
n
Mobile phone to resume playing music after hanging up phone call
l
3 party phone call:
- Short press Function button to connect the waiting phone call and hang off
current call
- Long press 1s the Function button to connect the waiting phone call and hold
current call. Long press 1s again to switch the two phone call status
§ 15.19 Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference,
and (2) This device must accept any interference, including interference that may cause undesire
d operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Table of contents
