Doughpro OSL1577 User manual

Operations Manual
SL1577
Split Lid Clam Shell Grill
Doughpro
20281 Harvill Ave
Perris, CA 92570
Phone [phone]
Toll Free [phone]
Fax [phone]
Website: www.doughpro.com
E-Mail: [email protected]
Listed:

Operation Instructions
Please read carefully before attempting to use this appliance.
Step 1. Carefully unpack and clean grill plates with mild soap then sponge clean
with cold water.
Step. 2. Place in location where it will be used allowing for clearances per the
dimensions indicated.
WARNING! Allow 2” minimum clearance between adjacent equipment and/or
wall areas.
Do not touch hot surfaces.
Step 3. Plug into proper 3 prong wall outlet. If other appliances are connected
to the same circuit make sure the total load does not exceed maximum
ampacity of the circuit. Electrical information is as follows:
120V/60Hz/1 phase/2200W/18.3 Amps
208V/60Hz/1 phase/2800W/13.5 Amps
220V/60Hz/1 phase/2200W/10.0 Amps
Step 4: Warm-up
Energize by turning on the power switch which will illuminate when turned
on. The display flashes and shows left preset timer during warm-up. Pre-
heat temperature time will be 40-50 minutes. When the set point is
reached, the display stops flashing and beeps 3 times.
Step 4: Operation
Simply place product on either side of the grill, close lid and press the
desired pre-set time cycle 10 or 20 seconds. After the time cycle is
finished press it again to reset the time cycle.
Cleaning Instructions
NOTE! Always turn off power and allow to cool down before attempting to clean.
Never submerge grill in water or other liquid nor use mineral spirits
or other flammable material to clean this appliance.
!Never use ice to cool down grill, warranty will be void!
Clean stainless steel and griddle surfaces with soap and water using a
soft, clean cloth periodically as required, but at least once daily. Never
use harsh abrasives. Use only non-abrasive scouring pads when required.

Clean Cycle
275°F is the factory default temp for the CLEAN cycle. To change the CLEAN cycle temp, simultaneously
hold down the TEMP and CLEAN buttons for 15 seconds. The current temp setting will display on the
right digital display only. Using the up or down arrows to adjust to the desired temp.
To start a clean cycle, push CLEAN button once so the CLEAN LED light is turned on. All preset LED’s are
turned off, and the temperature set point is changed to the clean set point of 275°F. This also initiates
the cool down to clean set point condition as well the display starts flashing until the clean set point is
reached.
To stop the clean cycle, simply press the CLEAN button once to deactivate the clean cycle. The CLEAN
LED is turned off, the preset LED’s are restored, the temperature set point is changed to the main set
point. Again, the warm-up condition is initiated and the display flashes until the cook set point is
reached.

SL1577 Operating Instructions:
1. Press desired time to start the time cycle. After the cycle is finished, press it again to
reset the time cycle
HOW TO IND TEMPERATURE
1. To find the temperature of the UPPER PLATENS:
Press the TEMPERATURE button and the ARROW UP button at the same time.
2. To find the temperature of the LOWER PLATENS:
Press the TEMPERATURE button and the ARROW DOWN button at the same time
*
* 275° is the factory default temp for the CLEAN cycle. To change the CLEAN cycle temp,
simultaneously hold down the TEMP and CLEAN buttons for 15 seconds. The current temp setting will
display on the right digital display only. Using the up or down arrows to adjust to the desired temp.

Instruction’s for Adjusting the Temperature
PRESS and hold the TEMP and
ARROW up
buttons simultaneously for 15
seconds.
The current temperature setting
will display on the right
digital display only.
Using the ARROW buttons, you
may now adjust the temperature
to your
desired setting.
Once you have set your desired
temperature simply push
the TEMP button. The digital
displays will now read the
preset times.
Instruction’s for Adjusting the Set-Time
PRESS the desired button you
wish to program.
Now press BOTH button and
TEMP buttons simultaneously
for 5 seconds.
The digital displays will now read their preset
times as
shown here. Each side is capable of having
up to 4
different settings, making a total of 8 set-
times.
Now using the ARROW buttons you
can set your desired time.
Once you have set the desired time simply press the
TEMP button, the unit will display the new set-time.
*IMPORTANT NOTE: When adjusting the time settings, The RIGHT SIDE time buttons
control the left side, so the same time you set on the right will automatically be set to
the left side accordingly. If you desire an additional set of times you can adjust the left
side AFTER you have adjusted the right side without effecting the right side settings.

MODEL SL1577_072111
PAGE 1 OF 3
8
7
83
69
869
83
9
8
69
83
1
4
3
96
95
72
7
86
87
73
2
14
7
74
50
5
46
A6
31
29
6
A3

A2
A1
21
22
11
50
74
33
26
25
20
22
11
74 50
29
29
24
27
28
31 29
60
11
10
34
35
36
38 37
40
29 41 38
38 41
29
39 38
37
23
33
32
25
29
30 29
29
31
60
28
27
MODEL SL1577_072111
PAGE 2 OF 3

A4
A5
25
57
56
77
28 61
64
59
52
64
53
62
59
28
77
56
57
25
68
78
54 78
78
58
51
85
49
48
47
16
45
66
78
58
78
54
68
78
12
81
13
88
89
89
88
18
17
80
94
19
79
15
51
85
90
91 93
92
92
91
93
92 92
65
16
16
75
75
93
91
78
78
97
C
D
55
MODEL SL1577_072111
PAGE 3 OF 3

SL1577
MODEL MODEL MODEL MODEL MODEL QTY.
SL1577YA SL1577A SL1577B SL1577C SL1577E
ITEM # PART NAME 120 V 120 V 220 V 220 V 208 V
1 LOWER WRAP AROUND SHROUD ASSEMBLY 110115501 110115501 110115501 110115501 110115501 1
2 LOWER PLATEN 1101007002120 1101007002120 1101007002220 1101007002220 1101007002208 1
3 LOWER PLATEN INSULATION 110115542 110115542 110115542 110115542 110115542 1
4 COVER, LOWER PLATEN ASSEMBLY 110115506 110115506 110115506 110115506 110115506 1
5 SET SCREW 5/16-18 x ½ SST5161812 SST5161812 SST5161812 SST5161812 SST5161812 1
6 SCREW SET 3/8-16 x 1-3/4 SST3816134 SST3816134 SST3816134 SST3816134 SST3816134 4
7 GREEN INSULATION WASHER C4401 C4401 C4401 C4401 C4401 10
8 HEX NUT 3/8-16 NH3816 NH3816 NH3816 NH3816 NH3816 4
9 STRAIN FELIEF MPSS168 MPSS168 MPSS168 MPSS168 MPSS168 1
10 SET SCREW 3/8-16 x 1.0 SST38161 SST38161 SST38161 SST38161 SST38161 2
11 SET SCREW 3/8-16 x ½ SST381612 SST381612 SST381612 SST381612 SST381612 4
12 FUSE HOLDER 1 AMP MPPF708 MPPF708 MPPF708 MPPF708 MPPF708 1
13 FUSE BUSS 1 AMP MPPF701R MPPF701R MPPF701R MPPF701R MPPF701R 1
14 PIN, BACK STOP 110115543 110115543 110115543 110115543 110115543 2
15 RELAY 110942520 110942520 110942520 110942520 110942520 3
16 SCREW, PHILLIPS. PAN HEAD 8-32 x 3/8 S.S.T SP83238S SP83238S SP83238S SP83238S SP83238S 7
17 4 STAGE TERMINAL BLOCK DOUBLE 6014 6014 6014 6014 6014 1
18 TRANSFORMER 11096975 11096975 11096975 11096975 11096975 1
19 4 STAGE TERMINAL BLOCK SINGLE 6994 6994 6994 6994 6994 1
20 UPPER PLATEN RIGHT HAND 110115540R120 110115540R120 110115540R220 110115540R220 110115540R208 1
21 UPPER PLATEN LEFT HAND 110115540L120 110115540L120 110115540L220 110115540L220 110115540L208 1
22 RTD SENSOR 1105911101 1105911101 1105911101 1105911101 1105911101 2
23 GROMMET 5/16 x 1/2 110115554 110115554 110115554 110115554 110115554 2
24 CLEVIS ASSEMBLY LEFT HAND 110115503 110115503 110115503 110115503 110115503 1
25 E-CLIP, RETAINING RING LCC3478 LCC3478 LCC3478 LCC3478 LCC3478 4
26 HANDLE LEFT ASSEMBLY 110115522 110115522 110115522 110115522 110115522 1
27 SOCKET HEAD SCREW 5/16-18 x ¾ SSH5161834 SSH5161834 SSH5161834 SSH5161834 SSH5161834 6
28 WASHER 5/16, LOCK WL516 WL516 WL516 WL516 WL516 10
29 BUSHING TEFLON 1” LONG 110115541 110115541 110115541 110115541 110115541 8
30 CLEVIS ASSEMBLY RIGHT HAND 110115504 110115504 110115504 110115504 110115504 1
31 FLANGED BUSHING TEFLON 1/2” LONG 110115563 110115563 110115563 110115563 110115563 2
32 HANDLE RIGHT ASSEMBLY 110115521 110115521 110115521 110115521 110115521 1
33 HANDLE GRIP 110901168 110901168 110901168 110901168 110901168 2
34 TUBING PAD 110115531 110115531 110115531 110115531 110115531 2
35 SPRING, DETENT 1-1/2 LONG 110115555 110115555 110115555 110115555 110115555 2
36 PLUNGER ASSEMBLY 110115544 110115544 110115544 110115544 110115544 2
37 HANDLE SPRING ADJUSTING COLLAR 110115528 110115528 110115528 110115528 110115528 2
38 SCREW SET KNURLED CUP POINT 5/16-18 x 3/8 SST5161838KN SST5161838KN SST5161838KN SST5161838KN SST5161838KN 12
39 COUNTER BALANCE SPRING RIGHT HAND 1101023154R 1101023154R 1101023154R 1101023154R 1101023154R 1
40 COUNTER BALANCE SPRING LEFT HAND 1101023154L 1101023154L 1101023154L 1101023154L 1101023154L 1
41 COLLAR HOLDER 110115530 110115530 110115530 110115530 110115530 2
44 GREASE TRAY 110115505 110115505 110115505 110115505 110115505 1
45 OVERLAY OPROSL1577Y OPROCSD301515 OPROCSD301515 OPROCSD301515 OPROCSD301515 1
46 SENSOR 1105911102 1105911102 1105911102 1105911102 1105911102 1
47 INSTRUMENT HOUSING ASSEMBLY 110115511 110115511 110115511 110115511 110115511 1
48 NYLON SPACER 1/4” x .141 x 9/32 LONG 11090109 11090109 11090109 11090109 11090109 6
49 DIGITAL CONTROL 1101041052 1101041052 1101041052 1101041052 1101041052 1
50 WASHER, SAE #6 WSAE6 WSAE6 WSAE6 WSAE6 WSAE6 3
51 NUT 6-32 NH632 NH632 NH632 NH632 NH632 18
SL1577_072111 PART LIST

SL1577
52 INSULATION UPPER PLATEN LEFT HAND 110888251L 110888251L 110888251L 110888251L 110888251L 1
53 INSULATION UPPER PLATEN RIGHT HAND 110888251R 110888251R 110888251R 110888251R 110888251R 1
54 TOP LINK 110115508 110115508 110115508 110115508 110115508 2
55 WIRE HARNESS 1101101050 1101101050 1101101050 1101101050 1101101050 1
56 UPPER LEVELING BRACKET 110115510 110115510 110115510 110115510 110115510 2
57 UPPERLEVELING SHIM 110115557 110115557 110115557 110115557 110115557 2
58 PIN PIVOT FRONT 110115565 110115565 110115565 110115565 110115565 2
59 SCREW BOLT HEX HEAD 5/16-18 X 1.0 S.S.T BH516181S BH516181S BH516181S BH516181S BH516181S 4
60 WASHER CUT 5/16 WC516 WC516 WC516 WC516 WC516 6
61 SHROUD, LEFT ASSEMBLY 110115553 110115553 110115553 110115553 110115553 1
62 SHROUD, RIGHT ASSEMBLY 110115552 110115552 110115552 110115552 110115552 1
64 SCREW, SLOTTED PAN HEAD 10-24 x 5/8 S.S.T SPS102458S SPS102458S SPS102458S SPS102458S SPS102458S 8
65 BACK COVER 110115562 110115562 110115562 110115562 110115562 1
66 POWER CORD 1101217174 1101217174 1101217175 MPPW202 1101217175 1
68 PIN PIVOT BACK 110115566 110115566 110115566 110115566 110115566 2
69 WASHER 3/8 LOCK WL38 WL38 WL38 WL38 WL38 4
72 SCREW BOLT HEX HEAD 1/4-20 x 1.0 BH14201 BH14201 BH14201 BH14201 BH14201 2
73 NUT SARRATED FLANGED 1/4-20 NHSF1420 NHSF1420 NHSF1420 NHSF1420 NHSF1420 2
74 SCREW, PHILLIPS. PAN HEAD 6-32 x ¼ SP63214 SP63214 SP63214 SP63214 SP63214 3
75 SCREW, PHILLIPS. PAN HEAD 8-32 x 1-1/2 S.S.T SP832112S SP832112S SP832112S SP832112S SP832112S 2
77 WASHER LOCK INTERNAL TOOTH WLIT516 WLIT516 WLIT516 WLIT516 WLIT516 4
78 RETAINING RING 110115567 110115567 110115567 110115567 110115567 8
79 MARKER STRIP, #4 SINGLE MS6994 MS6994 MS6994 MS6994 MS6994 1
80 MARKER STRIP, #4 DOUBLE MS6014 MS6014 MS6014 MS6014 MS6014 1
81 SCREW, PHILLIPS. PAN HEAD 2-56 x ¼ SP25614 SP25614 SP25614 SP25614 SP25614 1
83 WASHER, SAE 3/8 WSAE38 WSAE38 WSAE38 WSAE38 WSAE38 4
85 WASHER, #6 INTERNAL TOOTH LOCK WLIT6 WLIT6 WLIT6 WLIT6 WLIT6 18
86 WASHER, SAE ¼ WSAE14 WSAE14 WSAE14 WSAE14 WSAE14 2
87 WASHER, LOCK ¼ WL14 WL14 WL14 WL14 WL14 2
88 SCREW PHILLIPS PAN HEAD 6-32 x 3/8 SP63238 SP63238 SP63238 SP63238 SP63238 8
89 SCREW PHILLIPS PAN HEAD 6-32 x 5/8 SP63258 SP63258 SP63258 SP63258 SP63258 4
90 SCREW PHILLIPS PAN HEAD 8-32 x 1.0 SP8321 SP8321 SP8321 SP8321 SP8321 1
91 NUT, HEX 8-32 NH832 NH832 NH832 NH832 NH832 3
92 WASHER #8 WSAE8 WSAE8 WSAE8 WSAE8 WSAE8 4
93 INTERNAL TOOTH LOCK WASHER #8 WLIT8 WLIT8 WLIT8 WLIT8 WLIT8 3
94 MOUNTING BRACKET ASSEMBLY 110115559 110115559 110115559 110115559 110115559 1
95 COVER, HEATER ELEMENT 110115564 110115564 110115564 110115564 110115564 1
96 SCREW, PAN HEAD PHILLIPS 6-32 X .250 SP63214ST SP63214ST SP63214ST SP63214ST SP63214ST 2
97 SPATUTAL HOLDER 110115513 N/A N/A N/A N/A 1
A1 UPPER PLATEN LEFT HAND WITH WIRING 1101155201 1101155201 1101155202 1101155202 1101155203 1
A2 UPPER PLATEN RIGHT HAND WITH WIRING 1101155204 1101155204 1101155205 1101155205 1101155206 1
A3 LOWER PLATEN WITH WIRING 1101155207 1101155207 1101155208 1101155208 1101155209 1
A4 UPPER PLATEN LEFT HAND ASSEMBLY 1101155110 1101155110 1101155111 1101155111 1101155112 1
A5 UPPER PLATEN RIGHT HAND ASSEMBLY 1101155113 11011551113 1101155114 1101155114 1101155115 1
A3,A6 LOWER PLATEN ASSEMBLY 1101155116 1101155116 1101155117 1101155117 1101155118 1
SL1577_072111 PART LIST