Doughpro Progrill CS1500 User manual

formerly DOUGHPRO. New Name. Same Quality. Superior Service.
proluxe.com
Operations Manual
Model: CS1500
Clam Shell Grill

Operation Instructions
Please read carefully before attempting to use this appliance.
Step 1. Carefully unpack and clean grill plates with mild soap then sponge clean
with cold water.
Step. 2. Place in location where it will be used allowing for clearances per the
dimensions indicated.
WARNING! Allow 2” minimum clearance between adjacent equipment and/or
wall areas.
Do not touch hot surfaces.
Step 3. Plug into proper 3 prong wall outlet. If other appliances are connected
to the same circuit make sure the total load does not exceed maximum
ampacity of the circuit. Electrical information is as follows:
120V/60Hz/1 phase/2200W/18.3Amps
or
220V/60Hz/1 phase/2200W/9.2Amps
Step 4.
Cleaning Instructions
NOTE! Always turn off power and allow to cool down before attempting to clean.
Never submerge grill in water or other liquid nor use mineral spirits
or other flammable material to clean this appliance.
!Never use ice to cool down grill, warranty will be void!
Clean stainless steel and griddle surfaces with soap and water using a
soft, clean cloth periodically as required, but at least once daily. Never
use harsh abrasives. Use only non-abrasive scouring pads when required.

1
3
4
A4
5
6
7
8
9
10
11
12
13
14
15
11
17
85
87
86
2
25
26
16
A2
2A
CS1500P
A2
60
88
EXPCS1500 R4 10416 112612.DWG
SHEET 1 OF 3

A1
17
20
21
22
23
27
24
89
26
28
29
30
23
26
26
26
89
31
27
28
29
30 32
33
34
35
36
37
39
16 18
38
16
38 19
39
16
85
EXPCS1500 R4 10416 112612.DWG
SHEET 2 OF 3
A1
20A
17
85
CS1500P/PT
60

50
29
48
47
46
44 45
42
23
46
47
48
29
50
A3
57
56
58
59 61
62 63
64
66
66
68
65 66
66
71
66
65 68
66
66
66
72
64
64
63
62
77
78
79
80
41
83
81
40
75 51
70
75
51
70
76
84
51
70
82
69
69
EXPCS1500 R4 10416 112612.DWG
SHEET 3 OF 3
53
49 62
55
54
73
85
52
SERIAL No. MODEL No. MODEL No. MODEL No.
10416 CS1500A CS1500PA CS1500PTA
20006 CS1500B CS1500PB CS1500PTB
40003 CS1500C CS1500PC CS1500PTC
30032 CS1500E CS1500PE CS1500PTE

CS1500
A MODEL B MODEL C MODEL E MODEL QTY.
CS1500/CS1500P/CS1500PT CS1500/CS1500P/CS1500PT CS1500/CS1500P/CS1500PT CS1500E/CS1500PE/CS1500PT
ITEM # PART NAME 120 V 220 V 220 V 208 V
1 LOWER WRAP AROUND SHROUD ASSEMBLY 110115501 110115501 110115501 110115501 1
2 LOWER PLATEN 1101007002120 1101007002220 1101007002220 1101007002208 1
2A LOWER PLATEN PANINI 1101155132120 1101155132220 1101155132220 1101155132208 1
3 LOWER PLATEN INSULATION 110115542 110115542 110115542 110115542 1
4COVER, LOWER PLATEN ASSEMBLY 110115506 110115506 110115506 110115506 1
5 WASHER, SAE 3/8 WSAE38 WSAE38 WSAE38 WSAE38 4
6 WASHER, 3/8 SPLIT LOCK WL38 WL38 WL38 WL38 4
7NUT, HEX 3/8-16 NH3816 NH3816 NH3816 NH3816 4
8STRAIN FELIEF 11016546468 11016546468 11016546468 11016546468 1
9PIN, BACK STOP 110115543 110115543 110115543 110115543 2
10 BOLT, HEX 1/4-20X1 BH14201 BH14201 BH14201 BH14201 2
11 GREEN INSULATION WASHER C4401 C4401 C4401 C4401 10
12 WASHER, SAE #14 WSAE14 WSAE14 WSAE14 WSAE14 2
13 WASHER, SPLIT LOCK 1/4 WL14 WL14 WL14 WL14 2
14 NUT, HEX 1/4-20 NH1420 NH1420 NH1420 NH1420 2
15 SCREW SET 3/8-16 x 1-3/4 SST3816134 SST3816134 SST3816134 SST3816134 4
16 SCREW SET KNURLED CUP POINT 5/16-18 x 3/8 SST5161838KN SST5161838KN SST5161838KN SST5161838KN 15
17 SCREW, PAN HEAD PHILLIPS 6-32X1/4 SP63214 SP63214 SP63214 SP63214 2
18 COUNTER BALANCE SPRING LEFT HAND 1101023154L 1101023154L 1101023154L 1101023154L 1
19 COUNTER BALANCE SPRING RIGHT HAND 1101023154R 1101023154R 1101023154R 1101023154R 1
20 UPPER PLATEN 110121731120 110121731220 110121731220 110121731208 1
20A UPPER PLATEN PANINI 110121740120 110121740220 110121740220 110121740208 1
21 CLEVIS ASSEMBLY LEFT HAND 110115503 110115503 110115503 110115503 1
22 CLEVIS ASSEMBLY RIGHT HAND 110115504 110115504 110115504 110115504 1
23 E-CLIP, RETAINING RING LCC3478 LCC3478 LCC3478 LCC3478 4
24 HANDLE RIGHT ASSEMBLY 110115521 110115521 110115521 110115521 1
25 FLANGED BUSHING TEFLON 1/2” LONG 110115563 110115563 110115563 110115563 2
26 BUSHING TEFLON 1” LONG 110115541 110115541 110115541 110115541 6
27 HANDLE GRIP 110901168 110901168 110901168 110901168 2
28 WASHER, CUT 5/16 WC516 WC516 WC516 WC516 6
29 WASHER, 5/16 SPLIT LOCK WL516 WL516 WL516 WL516 10
30 SCREW, SOCKET HEAD 5/16-18X3/4 SSH5161834 SSH5161834 SSH5161834 SSH5161834 6
31 HANDLE LEFT ASSEMBLY 110115522 110115522 110115522 110115522 1
32 GROMMET 5/16 x 1/2 110115554 110115554 110115554 110115554 2
33 SCREW, SET 3/8-16 X 1/2 SST381612 SST381612 SST381612 SST381612 2
34 SCREW, SET 3/8-16 x 1.0 SST38161 SST38161 SST38161 SST38161 2
35 TUBBING PAD 110115531 110115531 110115531 110115531 2
36 SPRING, DETENT 110115555 110115555 110115555 110115555 2
37 PLUNGER ASSEMBLY 110115544 110115544 110115544 110115544 2
38 HANDLE HOLDER 110115530 110115530 110115530 110115530 2
39 HANDLE SPRING ADJUSTING COLLAR 110115528 110115528 110115528 110115528 2
40 TRANSFORMER 11096975 11096975 11096975 11096975 1
41 SCREW, PAN HEAD PHILLIPS 6-32 X 3/8 SP63238 SP63238 SP63238 SP63238 2
42 INSULATION UPPER PLATEN 110888254 110888254 110888254 110888254 1
43 N/A N/A N/A N/A N/A N/A
44 SHROUD 110121721 110121721 110121721 110121721 1
45 SCREW, PAN HEAD SLOTED 10-24 x 5/8 SST SPS102458S SPS102458S SPS102458S SPS102458S 6
46 UPPER LEVELING SHIM 110115557 110115557 110115557 110115557 2
47 UPPER LEVELING BRACKET 110115510 110115510 110115510 110115510 2
48 WASHER 5/16 INTERNAL TOOTH LOCK WLIT516 WLIT516 WLIT516 WLIT516 4
49 SWITCH, GUARD 110901413 110901413 110901413 110901413 1
50 BOLT HEX 5/16-18 X 1.0 SST BH516181S BH516181S BH516181S BH516181S 4
51 WASHER, #8 INTERNAL TOOTH LOCK WLIT8 WLIT8 WLIT8 WLIT8 3
52 WIRE HARNESS 1101217050 1101217050 1101217050 1101217050 1
53 PILOT LIGTH 110966018G 110966018G 110966018G 110966018G 1
54 SWITCH ASSEMBLY 110901411 110901411 110901411 110901411 1
55 TEMPERATURE CONTROLLER 1101217052 1101217052 1101217052 1101217052 1
56 INSTRUMENT HOUSING ASSY 110121711 110121711 110121711 110121711 1
57 OVERLAY OPRCCS1500 OPRCCS1500 OPRCCS1500 OPRCCS1500 1
PLCS1500 R4 10416 112612.DOC

CS1500
A MODEL B MODEL C MODEL E MODEL QTY.
CS1500/CS1500P/CS1500PT CS1500/CS1500P/CS1500PT CS1500/CS1500P/CS1500PT CS1500E/CS1500PE/CS1500PT
58 GREASE TRAY 110115505 110115505 110115505 110115505 1
59 NYLON SPACER 1/4” x .141 x 9/32 LONG 11090109 11090109 11090109 11090109 4
60 SHIM, LOWER PLATEN 11060420 11060420 11060420 11060420 1
61 DIGITAL TIMER 110121752 110121752 110121752 110121752 1
62 WASHER, #6 INTERNAL TOOTH LOCK WLIT6 WLIT6 WLIT6 WLIT6 10
63 NUT, HEX 6-32 NH632 NH632 NH632 NH632 8
64 SCREW, PAN HEAD PHILLIPS 8-32X3/8 SST SP83238S SP83238S SP83238S SP83238S 7
65 PIN, PIVOT FRONT 110115565 110115565 110115565 110115565 2
66 RATAINING RING 110115567 110115567 110115567 110115567 8
67 N/A N/A N/A N/A N/A N/A
68 TOP LINK 110115508 110115508 110115508 110115508 2
69 PIN, PIVOT BACK 110115566 110115566 110115566 110115566 2
70 NUT, HEX 8-32 NH832 NH832 NH832 NH832 3
71 POWER CORD 1101217174 1101217175 MPPW202 1101217175 1
72 BACK COVER 110115562 110115562 110115562 110115562 1
73 TRANSFORMER INSULATION 1101159180 1101159180 1101159180 1101159180 1
75 WASHER, SAE #8 WSAE8 WSAE8 WSAE8 WSAE8 4
76 SCREW, PAN HEAD PHILLIPS 8-32 X 1.0 SP8321 SP8321 SP8321 SP8321 1
77 MOUNTING BRACKET ASSEMBLY 110115559 110115559 110115559 110115559 1
78 FUSE HOLDER 1 AMP MPPF708 MPPF708 MPPF708 MPPF708 1
79 SCREW, PAN HEAD PHILLIPS 2-56X1/4 SP25614 SP25614 SP25614 SP25614 1
80 FUSE BUSS 1 AMP MPPF701R MPPF701R MPPF701R MPPF701R 1
81 MARKER STRIP, #4 DOUBLE MS6014 MS6014 MS6014 MS6014 1
82 4 STAGE TERMINAL BLOCK DOUBLE 6014 6014 6014 6014 1
83 SCREW, PAN HEAD PHILLIPS 6/32 X 5/8 SP63258 SP63258 SP63258 SP63258 2
84 SCREW, PAN HEAD PHILLIPS 8-32 x 1-1/2 SST SP832112S SP832112S SP832112S SP832112S 2
85 WASHER, SAE #6 WSAE6 WSAE6 WSAE6 WSAE6 6
86 COVER, HEATER ELEMENT 110115564 110115564 110115564 110115564 1
87 SCREW, PAN HEAD PHILLIPS 6-32X1/4 ST SP63214ST SP63214ST SP63214ST SP63214ST 2
88 FEET, RUBBER 3/4" 11016546469 11016546469 11016546469 11016546469 4
89 BUSHING TEFLON 3/4” LONG 110113441 110113441 110113441 110113441 2
A1 CS1500 UPPER PLATEN (WIRING ONLY) 1101217201 1101217203 1101217203 1101217202 1
A1 CS1500P/PT UPPER PLATEN (WIRING ONLY) 1101217201P 1101217203P 1101217203P 1101217202P 1
A2 CS1500 LOWER PLATEN (WIRING ONLY) 1101155207 1101155208 1101155208 1101155209 1
A2 CS1500P/PT LOWER PLATEN (WIRING ONLY) 1101155207P 1101155208P 1101155208P 1101155209P 1
A3 CS1500 UPPER PLATEN ASSEMBLY 1101217101 1101217103 1101217103 1101217102 1
A3 CS1500P/PT UPPER PLATEN ASSEMBLY 1101217101P 1101217103P 1101217103P 1101217102P 1
A2, A4 CS1500 LOWER PLATEN ASSEMBLY 1101155116 1101155117 1101155117 1101155118 1
A2, A4 CS1500P/PT LOWER PLATEN ASSEMBLY 1101155116P 1101155117P 1101155117P 1101155118P 1
PLCS1500 R4 10416 112612.DOC

CS1500P WIRE DIAGRAM
CS1500
VAC: 120/220
AMPS: 18.3/10.0
WATTS: 2200
WDCS1500 R2 0512.DWG

PLEASE READ CAREFULLY BEFORE ATTEMPTING TO USE
THIS APPLIANCE.
LIMITED MACHINE WARRANTY
Proluxe warrants the CS1500, from manufacturing defects in workmanship and material sold within
the domestic United States.
WHAT IS COVERED
One year warranty for parts and labor.
HOW LONG DOES THE COVERAGE LAST
We will repair or replace the defective CS1500 on normal warranty one year parts and labor. The
heating elements on the upper and lower platen only; will be replaced by next day air service;
under the normal one year warranty. Such repair or replacement will be at the expense of Proluxe
on under the normal one year warranty.
WHAT WE WILL DO
Contact our Factory to obtain warranty service. Proluxe must issue a return authorization
number, and call tag, or find the name and location of a Factory Authorized Service Center
nearest you. When calling for service, please furnish the model number, serial number, and a
description of the problem.
HOW TO GET SERVICE
THE WARRANTIES PROVIDED BY PROLUXE DO NOT APPLY IN THE FOLLOWING INSTANCES:
WHAT THIS WARRANTY DOES NOT COVER
•Damage due to misuse, abuse, alteration, or accident.
•Improper or unauthorized repairs.
•Submerged in water.
•Dropped.
•Damage in shipment.
•Equipment exported to foreign countries.

Warranty & Return Policy
Proluxe warrants all products manufactured by it against defects in workmanship or materials from the date of purchase for a period of
(1) year on parts and labor. This warranty applies to only equipment purchased and used in the United States. Warranty period
shall begin when equipment ships and will not exceed 90 days past the original shipment date. Warranty travel shall only
be covered for 60 miles.
ALL WARRANTY SERVICE CALLS MUST BE APPROVED BY PROLUXE. IF THIS PROCEDURE IS NOT FOLLOWED,
WARRANTY SERVICE WILL NOT BE COVERED. WARRANTY SERVICE WILL BE PAID ON STRAIGHT TIME, OVERTIME WILL
NOT BE COVERED.
Exclusions:
1. WOOD / GAS FIRED OVENS: PROLUXE warranty applies to the main body of the oven being steel / refractory and insulation shall
be free from defects in materials and workmanship for a period of four years from the date of purchase. The gas equipment shall be
free from defects in materials and workmanship for a period of one (1) year
from the date of purchase. This warranty excludes the tandoori and home oven. Lifetime warranty against cracks on oven floor.
2. TANDOORI & HOME OVENS: PROLUXE warrants the Tandoori & Home Oven including gas equipment shall be free from defects
in materials and workmanship for a period of one (1) year from the date of purchase.
3. Air compressors are excluded from this warranty, but PROLUXE may act as a warranty expeditor in certain instances regarding
these compressors. The air compressor manufacturer provides a limited warranty
and a copy of this warranty is furnished with all compressors sold by PROLUXE. For prompt handling of compressor warranty claims
the instructions of the compressor manufacturer must be adhered to.
4. Equipment built to special order as well as accessories are not returnable unless defective within the terms of this warranty.
5. In no event shall PROLUXE be liable for consequential damages arising out of the failure of any of its products if operated
improperly or caused by normal wear or damage by operator abuse.
6. BC2325 pedestal warranty disclaimer: Pedestals shall only be covered under warranty if they have been cleaned using the factory
approved cleaning method. cracked or damaged pedestals must be inspected by the factory before warranty is authorized.
Returned Merchandise Policy:
Should it become necessary to return any of the company’s products, the following instructions must be adhered to: First,
contact our customer service department for approval and a return authorization number. Please have the serial number
of your item available at that time. All merchandise must be shipped freight prepaid by customer or service agency.
Subject to the inspection of the product by the company, a restocking charge of 20% of the Net purchased price paid to
PROLUXE will be assessed. Merchandise may not be returned for credit without prior written approval of PROLUXE. Collect shipments
will not be accepted. No returns after 60 days of original shipment date on machines. Purchased parts may not be returned after 30
days.
If upon inspection by PROLUXE or its authorized agent it is determined the equipment has not been used in an appropriate manner,
has been modified, or has not been properly maintained, or has been subject to misuse,
misapplication, neglect, abuse, accident, unauthorized modification, damage during transit, delivery, fire, flood, act or war,
riot or act of God, then this warranty shall be deemed null and void.
Terms & Conditions:
1. Prices indicated in the PRICE LIST are suggested retail prices and are shown in U.S. DOLLARS.
2. Terms of Payment: 1% 10 days, NET 30 days.
3. NEW ACCOUNTS: Satisfactory credit information must be provided before open account status can be extended.
Unless agreed otherwise, all shipments will be made C.O.D., CASH IN ADVANCE.
4. PRICING: Prices, specifications, model numbers, capacities and accessories are subject to change without notice.
5. FREIGHT / ROUTING: Method of shipment will be determined by PROLUXE unless otherwise
advised by PURCHASER.
6. DAMAGED CLAIMS: All merchandise shipped at purchaser’s risk. Inspection must be made by purchaser at time
goods are received. If goods are damaged, the PURCHASER shall request that the agent of the transportation
company make a written notation on the proper shipping documents immediately and then file a claim for damage.
GOODS DAMAGED IN SHIPMENT ARE NOT RETURNABLE.
7. RETURNS: Machines may not be returned after 60 days. Purchased parts may not be returned after 30 days. A
restocking fee of 20% will be assessed on non-warranty returns.
8. TAXES: Prices indicated herein DO NOT include State, Federal, Local or foreign taxes or duties, nor do they include
fees, permits, insurance or other levies, all of which are the responsibility of the purchaser.
9. All orders are subject to acceptance by PROLUXE.
10. Possession of this price list shall not be considered an offer to sell.