Douglas Lighting Controls WOSSID1-P-VW User manual

2.56 (65) 3.25 (83) 3.81 (97)
1.25 (32)
4 (101)
1.62 (41)
*Faceplate not included
PART NO. FEATURES
WOSSID1-P-VW
PIR, 24Vac, 1-pole,
photo, white
WOSSID2-DP-VW
PIR, 24Vac, 2-pole,
dimming, photo, white
WOSSID2-DP-VI
PIR, 24Vac, 2-pole,
dimming, photo, ivory
WOSSID2-DP-VG
PIR, 24Vac, 2-pole,
dimming, phote, grey
• Commercial grade components for long term reliability
• Straightforward wiring for quick installation
• Factory congured for the most common applications
• DIP switches and dials for advanced functionality
• Available in White, Ivory, Grey
• Options: Dimming Control, Photo Sensor
DIMENSIONS - inches (mm)SPECIFICATIONS
Wiring Diagrams
Diversa 24Vac sensors include #22 AWG wiring leads. Use appropriate sized wire nuts for connecting wires.
CAUTION: Turn power OFF at the circuit breaker before working on sensor. According to NEC 240-83(d), if the branch
circuit breaker is used as the main switch for a uorescent lighting circuit, the circuit breaker should be marked SWD.
All installations should be in compliance with National Electric Code (NEC) and all state, provincial, federal, and local
codes.
Operation
Low voltage sensors are powered by 24Vac from either the Diversa Series Power Pack (WP-PP20-***) or a 24Vac
transformer. When in operation the sensor will detect initial motion using Passive Infrared (PIR); once motion is
detected, the internal and Power Pack (or connected diode pulse relays) contacts will close. Motion through PIR is
used to maintain the occupied condition as long as occupants remain within coverage pattern of Sensor.
Inputs
•24Vac + _ 25%
•Class 2 Low Voltage Source
•60 Hz
•#18 AWG
Outputs
•Diode Pulse: Each outputis capable of driving up to four
Diode Pulse relays.
•0-10V Dimming: Connections are polarity sensitive.
Up to 25mA sinking.
Power C onsumption
•9.5mA Standard
Manual Override Button
DIP Switches
Time Delay Dial
Ranges from 30s to 30 min.
Full turn Clockwise for Auto Time
Full turn Counterclockwise for test mode
Auto
Test
TestMode
Lo Hi
1
5
30
20
Light Level Dial
Photo sensor “P”
models only
Automatic Timeout Mode LED
Sensor
Test Mode LED
Environment
• Indoors, stationary, non-vibrating, non-corrosive
atmosphere and non-condensing humidity
• Ambient Operating Temperature: 32°F to 104°F (0°C to
40°C)
• Storage Temperature: -14°F to 140°F (-25°C to 60°C)
2.65 (68)
1.18 (30)
1.69 (43)
Installation Coverage
Installing in Oces
•PIR Requires Line ofSight Installing in Restrooms
•Use 2-pole model to control two loads in
restroom (e.g. light and fan)
Typical Oce Typical Restroom
Standard Lens
•Optimal usage isto detect small motionssuch ashand movements
•Designed for a mounting height of4ft
Top View Side View
15 ft
7.5 ft
0 ft
7.5 ft
15 ft
180º
15º
15º
4 ft
0 ft
8 ft
0 ft
Sensor Location Guidelines
To optimize the performance of Diversa Sensors, please review the coverage pattern, range, and model to
match with the application. Room dynamics will change when people and furniture are occupying the space.
In some rooms, after move in, some sensors may require adjustments.
• Ensure that the sensor is at least 30 inches away from air handlers/registers and not pointed directly at
windows
Sensor Location Guidelines for“P” models
• Place outside the direct cone of light from xtures and between 3 to 12 feet from a window
• As close as possible to the xture being controlled
• Above the least illuminated space in the work area
• Away from lighting that is not being controlled by the sensor
15 ft
Wiring to a Power Pack
Black
White
Orange
Sensor
Link
WP-PP20-D
Override / Multi-Level
Switching
Black
White
Black
White
Red
Red
Red/White
Orange
Sw
Sw
Line Voltage Passive Infrared (PIR) Occupancy / Vacancy Sensor
Installation Guide
Diversa Occupancy & Vacancy Sensors - Wall Switch, Passive Infrared (PIR), 24Vac 14040400-C
www.douglaslightingcontrols.com
Diversa by Douglas Lighting Controls

Factory DIP and Dial Settings
UP
Down
12345678
TEST
Time Delay Dial
Light Level Dial
Photo Sensor “P” models
Dimming Control “DP” models
1
5
10
20
30
Hi
Lo
Auto
ON = Test
Mode
Troubleshooting
Before calling Technical Support, please review the following Troubleshooting Guide.
DIP Switch Modes
DIP 1 - PIR Detection LED
LED in Sensor’s PIR window ashes GREEN when PIR detects motion. LEDs can be turned OFF with DIP switch. Sensor
continues to function.
DIP 2 - Walk-Through Mode
When Enabled and Occupancy switches lights to ON and sensor does not detect motion after 30 seconds of light ON,
an OFF Time Delay of 3 minutes is used (OFF Time Delay must be greater than 3 minutes). If motion is detected after
30 seconds of lights ON, the congured OFF Time Delay is followed.
DIP 3 - Manual Override
Manual Override Button can be disabled with DIP switch to prevent manual ON/OFF.
DIP 4 - Sensor Mode
Vacancy Mode - Lights must be turned ON manually when entering a room and are automatically turned OFF when
occupancy no longer detected. Maximizes energy savings because lights are only turned on when lighting is
required.
Occupancy Mode - Automatically turns lights ON when occupancy is detected in a room and automatically turns
lights OFF when occupancy is no longer detected. This is a very convenient mode as lighting controls never have to
be touched. Because lights are always turned on when Occupancy is detected regardless of the need for lighting,
this is less energy efficient than Vacancy Mode.
DIP 5 - PIR Sensitivity
Can be moved from Medium sensitivity (default) to High sensitivity if sensor is not recognizing Occupancy.
DIP 6 - Natural Daylight Mode (”P” models)
When ENABLED, lights ON when Occupancy detected AND daylight level is below Light Level Dial setting. With lights
ON, an increase in daylight above the Light Level Dial setting will not force lights OFF.
DIP 7 - Light Level Mode (”DP” models)
This mode allows the light function to be set and controlled to support Natural Daylight Mode and Closed Loop
dimming. WIth DIP UP the light level dial is used for setting the light level for Natural Daylight Mode. With DIP DOWN,
the light level dial is used for setting Closed Loop Dimming.
DIP 8 - Restroom Mode (2-pole models)
Pole 1 and Pole 2 are set to synchronize to the same Photo and Time Delay settings. With Restroom Mode = Offset,
Pole 2 will activate at the same moment as Pole 1 when Occupancy detected; however, Pole 2 will be offset so that
OFF delayed 50% longer than Pole 1. (e.g. Light is Pole 1 and Fan is Pole 2. Fan would stay ON 50% longer than light).
Auto Time Mode
Activated when Time Delay Dial is set to Auto Time. Red LED indicator will be ON. In this mode, time delay will start
automatically set by the sensor learning occupancy patterns.
Test Mode
Activated when Time Delay Dial is set to TEST. Test Mode LED will ash red for 5 minutes, providing a short Time Delay
when testing the installation to determine if the sensor is working as intended or requires adjustments. After 5
minutes, LED will stop ashing and Time Delay reverts to Factory Time Delay setting (10 minutes).
DIP Switches & Dial Settings
Some DIP Switches Control Optional FeaturesNot Found on All Product
DIP # Function UP DOWN Default
1PIR LED Disabled Enabled DOWN
DOWN
DOWN
DOWN
DOWN
DOWN
DOWN
DOWN
2Walk-Through
Mode Enabled Disabled
3Manual Override Disabled Enabled
4Sensor Mode Manual ON (Vacancy) Auto ON (Occupancy)
5 PIR Sensitivity High Medium
6Natural Daylight
Mode (”P” models) Disabled Enabled
7Light Level Mode
(”DP” models)
Light Level Dial
Sets Photo Sensor
Light Level Dial
Sets Dimming Level
8Restroom Mode
(2-pole models) Synchronized
Offset
General Programming Instructions
This covers mode programming using the onboard DIP and Dial switches.
***NOTE***
•Start with the PIR Sensitivity at Medium
•To set the light level at which you want to inhibit the sensor from turning on, put DIP 6 in DOWN
position and simply rotate the Light Level Dial to adjust the light level
•To enable Restroom Mode , ensure that DIP 8isUP. In thismode Pole 2 will remain ON 50%
longer than Pole 1 (Time isset with the Time Dial)and Pole 2 cannot be Photo Inhibited
Factory Defaults
All DIP switches in DOWN position. Time delay: 10 minutes; natural daylight level: 50% (200 lux).
Diversa Occupancy Sensors with a “P”in the model number contain a Photo Sensor that is
controlled by DIP 6. The factory default for Natural Daylight Mode = ENABLED (DIP 6 DOWN).
This mode disables the Manual Override Button. To test sensor functionality, you may need
to disable Natural Daylight Mode (DIP 6 UP) to test sensor functionality.
Issue Possible Cause Recommended Soluon
This only applies to Photo Sensor (”P”) models. Check DIP
6. If DOWN, sensor is in Natural Daylight Mode, therefore
lights will only turn ON if there is insufficient natural
daylight. Rotate the Light Level Dial clockwise pressing
the Manual Override Button until the Lights turn ON.
Natural Daylight mode can be disabled by moving DIP 6
U P.
Check DIP 4. Move DOWN for Auto ON.
Sensor is set to Manual ON Mode.
Sensor is in Auto Time Mode.
Lights will not turn
ON automatically
Lights will not turn
OFF automatically
Lights will not turn
OFF Manually
Lights will not turn
ON Manually
Sensor is set to Natural Daylight Mode (Photo
Inhibit) and Sufficient Natural Light is Present.
This only applies to Photo Sensor “P” models. Check DIP 6.
If DOWN, sensor is in Natural Daylight Mode; therefore,
lights will only turn ON if there is insufficient natural
daylight. Rotate the Light Level Dial clockwise pressing
the Manual Override Button until the lights turn ON.
Natural Daylight mode can be disabled by moving DIP 6
U P.
Sensor is set to Natural Daylight Mode (Photo
Inhibit) and Sufficient Natural Light is present.
Manual Override Button was used to turn lights
OFF.
Wait for OFF Time Delay to count down, then with
motion detected lights will turn ON. Manual Override
Button can be disabled by moving DIP 3 UP.
Power has been interrupted or wiring
connection is intermittent.
Power has been interrupted or wiring
connection is intermittent.
Sensor is being activated by a heat source other
than occupant.
Sensor may be detecting heat from HVAC registers or
other heat sources. Check Installation location for heat
source. Reduce PIR sensitivity by moving DIP 5 DOWN.
Move sensor location – see guidelines.
Manual Override Button has been disabled.
Check the wiring diagram. Ensure ground is connected.
With DIP 1 DOWN, check for motion detection by waving
hand in front of sensor lens. Activation LED will blinnk
green.
Check the wiring diagram. Ensure ground is connected.
With DIP 1 DOWN, check for motion detection by waving
hand in front of sensor lens. Activation LED will blinnk
green.
If the Sensor is in AUTO Mode, it may take longer than
expected to turn the lights off. Set the Time Delay to 5
minutes and leave space to determine if the Sensor is
functioining. The maximum Time Delay is 30 minutes.
Move DIP 3 DOWN to enable Manual Override Button.
Line Voltage Passive Infrared (PIR) Occupancy / Vacancy Sensor
Installation Guide
Diversa Occupancy & Vacancy Sensors - Wall Switch, Passive Infrared (PIR), 24Vac 14040400-C
www.douglaslightingcontrols.com
Diversa by Douglas Lighting Controls