Dovpo ROGUE 100 User manual

USER MANUAL

Rogue 100 is designed by Electron CIG, manufactured by
DOVPO, it houses a single 26650 high-drain battery, maximum
wattage goes up to 100W. Rogue 100 supports Power Mode,
Bypass Mode, Ni200/Ti/Ss316 Temp Control function as well
as the latest Customized Curve of Wattage/Temperature, aka
CCW/CCT mode. Rogue 100 has all the safety features to
ensure safe use of this product. Please read this manual
carefully, and follow its instructions closely before first use.
SPECIFICATIONS
Size: 44.2 x 31 x 91 mm
Material: Zinc Alloy
Display: 0.91” OLED
Wattage Range: 5.0W-100.0W
Temperature Range: 100℃-315℃
200℉-600℉
Input Voltage: 3.00V-4.25V
Output Voltage: 0V-8.50V
Resistance Range: 0.1Ω-5.0Ω
Battery: Single 26650 High-drain Battery
WORKING MODE
Power Mode/CCW Mode/Bypass/Ni200/Ni200 CCT/Ti/Ti CCT/
Ss/Ss CCT.
PROTECTION
Short Circuit Protection
Overcurrent Protection
Battery-Reversal Protection
Charging Protection
Over-heat protection
Overtime Warning
Low-resistance Protection
Low Voltage Protection
High-resistance Protection
1

OPERATION GUIDE
1. Battery Installation
The “DOVPO” logo will appear on screen after installing
battery, the device enters Power Mode.
0.00Ω
0.00V 100W
2. Switching Modes
Switch between each working modes by long pressing
Mode Button.
1.
2.
3.
Power Mode
CCW Mode
Bypass
4.
5.
6.
Ni200
CCT Ni200
Ti
7.
8.
9.
CCT Ti
Ss316
CCT Ss316
Press Fire Button to confirm.
3. Power On/Off
Click Fire Button 5 times in 2 seconds to turn the device
on. The settings will stay the same after reboot.
4. Wake/Sleep
The screen will go black after 30s of inactivity. Press any
button to wake up the device.
5. Power Mode
When in Power Mode, using the "+" or "-" button will
allow you to increase or decrease desired wattage by 1.0W.
Holding either button will cause the wattage to scroll more
quickly.
0.00Ω
0.00V 100W
2

6. CCW Mode
6.1 When in Power Mode, hold Mode Button to switch to CCW
Mode(Initial setting is 100W)
0.00Ω
0.00V
100W
CCW
10S
6.3 Now when you start vaping,
the output wattage will vary
according to your customized
settings in real time.
When in CCW Mode, the x-axis represents the timeline(10s in
total), y-axis represents the wattage. The selected wattage
value will flash, you can increase/decrease the wattage with
“+” or “-” button. Click the Mode Button to move around.
0.00Ω
0.00V
80W
CCW
10S
0.00Ω
0.00V
CCW 1S
6.2 Press Fire Button to confirm
the settings. You will see the
customized curve on screen.
0.00Ω
0.00V
BYPASS
7. Bypass Mode
Rogue 100 supports bypass
mode, working as a
mechanical mod, the output
power is unregulated in Bypass Mode.
8. Temperature Control Modes
Temperature Control Ni200, Temperature Control Ti,
Temperature Control Ss316
0.00Ω
0.00V
200 Ni
F
0.00Ω
0.00V
200
Ti
F
0.00Ω
0.00V
200 SS
F
3

When in Temperature Control Mode, using the "+" or
"-" button will allow you to increase or decrease desired
temperature by 5℃ or 10℉. Holding either button will
cause the temperature to scroll more quickly. When it
reaches the highest point of temperature in Celcius,
press “+” button again, it will go to the lowest point of
temperature in Fahrenheit. It works the other way
around.
9. CCT Mode
9.1 When in Temperature Control Mode, hold Mode Button to
switch to CCT Mode
0.00Ω
0.00V
520F 270C
CCT
10S
When in CCT Mode, the x-axis represents the timeline(10s in
total), y-axis represents the temperature. The selected
temperature value will flash, you can increase/decrease the
temperature with “+” or “-” button. Click the Mode Button to
move around.
0.00Ω
0.00V
CCT
10S
520F 270C
9.2 Press Fire Button to confirm settings.You will see the
customized curve on screen.
0.00Ω
0.00V
CCT
1S
Ti
9.3 Now when you start vaping, the temperature will vary
according to your customized settings in real time.
10. Flip Screen
Hold both “+” and “-” buttons to flip the screen.
4

11. Replace Atomizer
When replacing an atomizer, the display will show a New/
Same interface. See following picture.
Press the "+" button to confirm that is a new atomizer,
press the "-" button to confirm it is the same atomizer
and the resistance will stay the same.
12. Wattage/Temperature Lock
Hold both Fire Button and “-” button to lock the wattage/
temperature. The message “SYSTEM LOCKED” will appear
on screen. While wattage/temperature is locked, the
message “PRESS FIRE & DOWN TO UNLOCK” will appear
on screen when pressing “+” or “-” button, hold both
Fire Button and “-” button to unlock. You will see the
message “SYSTEM UNLOCKED” appear on screen.
ERROR MESSAGES
No Atomizer: “CHECK ATOMIZER”
Short Circuit: “SHORTED”
Resistance is higher than 5.0ΩHIGH ATOMIZER”
Resistance is lower than 0.1Ω: “HIGH ATOMIZER”
Board Temperature is above 80℃: “OVERHEAT”
Battery Voltage is below 2.8V: “LOW BATTERY”
Keep pressing the Fire Button for over 10s: “OVER 10S”
: “
5

When charging the battery with micro USB cable, the battery
icon will indicate it's getting filled up. The energy grid will
display full after battery being fully charged.
Maximum charging current is 1.5A. The screen will go dim
after the battery is fully charged.
You can vape while charging the Rogue 100, the device will
stop charging for the duration of the vape for safety purposes.
CHARGING
WARNING
1. Please use all accessories as intended to avoid damage to
your device.
2. Please use the original charging cable, or a quality
replacement when charging this device.
3. When not using your device for a long period of time,
please turn it off and store it in a cool dry place to
prevent potential damage. Check the battery periodically
for signs of discharge.
4. Should damage occur, please do not attempt to repair
yourself. Use any available warranty, or contact a
professional for repairs.
5. Please keep this product and accessories away from
children.
6. Please read this manual, and follow its instructions closely.
7. To clean the device, use only a slightly damp towel, and
do not allow moisture to get in the device.
6