Totally Wicked Rocket User manual

USER MANUAL BEDIENUNGSANLEITUNG

CONGRATULATIONS
ON PURCHASING YOUR
TOTALLY WICKED
ROCKET
ELECTRONIC
CIGARETTE KIT

3
CONGRATULATIONS
ON PURCHASING YOUR
TOTALLY WICKED
ROCKET
ELECTRONIC
CIGARETTE KIT
Rocket Battery
Power Button USB Port
LED Screen
510 Connection
Adjustable Airflow
Mouthpiece

4
Fuze Tank
Spare 510
Mouthpiece
Mouthpiece
Top Cap
Atomizer Head
Tank Glass
Atomizer Base

5
Using your Rocket Kit
Priming the atomizer head:
It is important to “prime” the
atomizer head before first use; this
ensures the atomizer head is fully
saturated with e-liquid. To prime the
atomizer head, remove the tank from
the Rocket battery then unscrew the
top cap assembly from the tank by
rotating anti-clockwise. The atomizer
head should remain attached to the
top cap assembly when removed
from the tank; the atomizer head
can then be unscrewed from the top
cap. Prime the atomizer head by
dripping a few drops of e-liquid into
the central hole in the atomizer head.
After priming, screw the atomizer
head back onto the top cap,
tightening until snug. Check that
the tank’s glass section is correctly
located on its seal on the atomizer
base of the Fuze tank, then screw
the top cap assembly, complete with
new atomizer head, back into the
tank. Tighten until snug, then fit the
fully assembled tank back onto the
Rocket battery.

6
Important note: It is possible to
assemble the Fuze tank by first
screwing the atomizer head onto
the base of the tank with glass
removed rather than the top cap.
This is not recommended, as it will
mean that the threads securing the
atomizer head to the top cap are
not fully engaged. If this incorrect
assembly procedure is used, the
atomizer head will remain attached
to the atomizer base when the top
cap is unscrewed. Should this occur,
remove the tank glass section from
the base of the tank and unscrew the
atomizer head. Refit the glass, then
refit the atomizer head to the top cap
assembly and reassemble the tank
as shown on page 4.
Using your Rocket Kit

7
Using your Rocket Kit
Filling the Fuze tank with e-liquid:
Fully close the airflow slot by
rotating the airflow control ring anti-
clockwise. The top cap cannot be
opened for filling unless the airflow is
fully closed. Locate the fill symbol on
top of the Fuze tank, and push/slide
the top section in the area of the
symbol, and in the direction pictured
below. The top cap will hinge open
to reveal two e-liquid fill holes. Fill
the tank with e-liquid, avoiding
overfilling. Take care to avoid
pouring e-liquid into the central air
hole. Once filled with e-liquid, close
the hinged top cap assembly then
firmly slide it shut. An audible click
will be heard when the top cap is
properly closed.
Note: Be sure to “prime” the
atomizer head before first use by
allowing it to sit in a tank full of
e-liquid for a few minutes before
vaping. This ensures the atomizer
head is fully saturated with e-liquid
prior to use.
See diagram on next page >

8
Using your Rocket Kit

9
Powering On and Off:
To switch the Rocket on, press the
power button five times in quick
succession; the Totally Wicked logo
will flash 5 times quickly, indicating
the battery has been switched on.
Similarly, when powered on, quickly
press the power button five times
to turn the battery off; the Totally
Wicked logo will flash 5 times
quickly, indicating the battery has
been switched off.
Vaping:
Press and hold the power button as
you inhale the vapour. The Totally
Wicked logo will light while the unit
is powering the atomizer coil.
Using your Rocket Kit

10
Installing/Replacing an Atomizer
Head:
To install a new atomizer head,
follow the instructions shown for
priming the atomizer head above.
Remember to prime your new
atomizer head before fitting.
Charging the Battery:
Charge by inserting the large side of
supplied USB cable into a powered
USB port or suitable wall adapter
and insert the cables micro USB
connection into the side of the
Rocket. When charging, the display
will flash 5 times to indicate charging
has started. The battery bars on the
screen will flash and progressively
increase until the Rocket is fully
charged, when fully charge the
display will switch off.
Using your Rocket Kit