Dovpo TOPSIDE Top Fill Squonk User manual

1. Size: 92.0mm x 54.0mm x 27.0mm
2. Material: Zinc Alloy, Aluminum Alloy, Stainless Steel.
3. All parts that have contact with eliquid are made from
food grade stainless steel and silicone.
4. Input Voltage Range: 3.2v – 4.2v
5. Output Voltage Range: 1.0v – 8.5v
6. Resistance Range: 0.08Ω – 3.5Ω
7. Working Mode: Variable Wattage & Bypass,
Temperature Control(Optional, see Firmware Update)
8. Wattage Range: 5.0W – 90.0W
9. Display: 0.96” OLED
10. Gold-plated Spring Loaded 510
11. Silicon bottles with a capacity of 10 ml
SPECIFICATIONS
Leak Resistant 510 base
Fire button
5-90W/1.0-8.5v
Chipset
0.96" OLED Screen
Up & Down Buttons
10ml Silicone Bottle
Top Cap
Battery cover

START VAPING
1. Install a single 21700/20700/18650 high-drain battery
Make sure the positive and negative ends are facing
the correct directions
2. Power On/Off: Click Fire Button 5 times quickly to turn
the device on, repeat the process to turn the device off.
3. Install the bottle carrier into the device.
4. Attach an atomizer to the device, set your desired
wattage/voltage and start vaping by pressing the Fire
Button.
5. To switch from Wattage Mode to Bypass Mode and
vice versa, hold both Fire Button and “-” Button.
6. Hold both “+” and “-” to LOCK the 'UP' and
'DOWN' buttons, repeat the process to UNLOCK.
SAFETY FEATURES & WARNINGS
1. Battery Reversal Protection
2. Short-circuit Protection: if there is a short circuit,
when you press the Fire Button, the screen will display
“SHORTED”.
3. If the resistance of the atomizer is lower than 0.08Ω,
when you press the Fire Button, the screen will display
“LOW Ω”
4. Open-circuit Warning: if there is no atomizer attached
or atomizer has an open circuit, when you press the
Fire Button, the screen will display“CHECK ATOMIZER”
5. Overtime Protection: the device will cut power after
10 seconds of continuous firing, screen will display
“OVER 10S”
6. Over-temperature Protection: if the board temperature
goes over 75℃/167°F, the device will cut power,
when you press Fire Button, the screen will display
“TOO HOT”.

7. Low-voltage Protection: if battery level is lower than
3.2v, when you press the Fire Button, the screen will
display “LOW BATTERY”
Firmware update:
Please Note: This device is built with the, simple to
understand and easy to use wattage mode/bypass
mode as the default firmware. If you prefer temperature
control, a TC firmware is available for you to download
and flash to your device.
Check your firmware version by holding “+” and “-”
buttons for 2s when the device is off.
Go to the following link to check if there's an update
available for your TOPSIDE firmware.
https://www.dovpoecig.com/topside-squonker
Follow the instruction on this webpage to update your
TOPSIDE firmware to the latest version.
WARNING
1. Please use all accessories as intended to avoid
damage to your device.
2. When not using your device for a long period of time,
please take out the batteries from the device.
3. Should damage occur, please do not attempt to repair
by yourself. Use any available warranty, in the first
instance contact the reseller you purchased the unit from
4. Please keep this product and accessories away from
children and pets.
5. To clean the device, use only a slightly damp towel, and
do not allow moisture to get inside of the device.
6. Over-temperature Protection: if the board temperature
goes over 75℃/167°F, the device will cut power, when
you press Fire Button, the screen will display“TOO HOT”
7. Low-voltage Protection: if battery level is lower than 6.4v
when you press the Fire Button, the screen will display
“LOW BATTERY”.