Dragon Touch KB10 User manual
Quick Start Guide
Wireless Security Camera
V1.0
Please read this manual before operating your Wifi camera,
and keep it for further reference.
KB10
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that
this devicedoes not cause harmful interference (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and
operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
FCC ID: 2AYD2-KB10
IC Caution:
English:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions: 1. This device may not cause interference. 2. This device must accept any interference,
including interference that may cause undesired operation of the device.
French:
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1. L’appareil ne
doit pas produire de brouillage; 2. L’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
To maintain compliance with ISED’s RF Exposure guidelines, This equipment should be installed and
operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
CONTENTS
01 - 18
37 - 54
WHAT’S IN THE BOX
NVR × 1 Security Camera × 4 Mouse × 1
Antenna Extension
Cable × 1
Network Cable × 1Power Adapter × 5
Quick Start Guide × 1
V1.0
Quick Start Guide
Dragon Touch K4W10 HD NVR KIT
INTRODUCTION
NVR Front Panel
NVR Back Panel
Audio-Out
VGA
HDMI
RJ45
USB
DC
Antenna PortAntenna Port
Antenna
USB
Alarm Indicator
Power Indicator
REC Indicator OK Button Menu
ESC
1 2
English
IPC (IP Camera)
CONNECTING YOUR SYSTEM
Hard Disk Installation
The NVR system requires a SATA internal hard drive or mobile hard disk drive for
video recording. The system can display real-time video, but you can’t record or
playback video footage without installing a hard drive. The system supports an up
to 8TB hard drive.
SATA Internal Hard Drive Installation
The system supports a 3.5” or 2.5" SATA internal hard drive (A 2.5" SATA internal
hard drive needs a bracket to hold the HDD).
1. Remove the screws 2. Remove the cover
4. Connect the power wire3. Connect the data wire
6. Put the cover back, and secure
the screws of the cover
5. Secure the screws of the hard drive
Note:
• 3OHDVHSRZHURWKH195EHIRUH\RXLQVWDOOWKHKDUGGULYH
• The system cannot record or playback video without a hard drive.
3 4
Antenna
DC Jack
RJ45 Port
LED Light
Lens
IR Lights
USB
Mobile HDD Installation
We provide a USB 2.0 port to connect a mobile HDD.
Note: Internet connection is required for remote viewing.
Note: Do not connect the NVR to a computer directly. It must be connected to a
TV or monitor only.
Connect the
monitor
Connect the
mouse
Connect the NVR and
IPC antenna
Connect to
power
(IPC and NVR)
Connect the
router
/$1RU:Lȴ
/$1:Lȴ
QUICK MENU
Right-click to open the Quick Menu
LOGIN AND CHANGE PASSWORD
1. Login: Log into the system by entering your user name and password (The
default user name is “admin” and there is no default password. You need to set
DQHZSDVVZRUGZKHQORJJLQJLQWRWKHGHYLFHIRUWKHȴUVWWLPH
Click the main menu to set your device.
&OLFNWRVHWWKHZLUHOHVVFKDQQHODQGZLȴFRQQHFWLRQ
Click to set the record mode for your device.
Click to search and playback the footage.
Click to set camera parameters.
Click to set the collective image parameters.
Click to set the view windows.
Click to control camera PTZ function (only for PTZ camera).
Click to set TV output area parameters.
Click to set the Net connection Status.
Click to log out, shut down or reboot the system.
5 6
System Connection
2. Change Password: Go to [Main Menu] →[System] →[Account] to change
the password.
DATE AND TIME SETTING
It is important to make sure that the correct time is set up so the NVR kit can
deliver accurate time stamps on all video recordings.
Go to [Main Menu] →[Date Time] to set the correct time for the system.
Click OK to save the settings.
WIRELESS SETTING
[IPC Connection Status]
Click [Wireless]WRJRWRWKHVHWWLQJPHQX\RXFDQVHWWKHΖ3&FKDQQHODQG:Lȴ
Connection.
Note: The menu shows the connection status under the NVR.
>:LUHG&RQȴJXUDWLRQ@ Search/Add/Delete/Clear the IP channel.
[Repeat Setting]: The system has an auto wireless relay transmission mode.
You can manually change settings here.
[Code for Wireless]: Pair the camera and NVR through a wireless signal.
7 8
[Wireless Connection]: 7RFRQQHFWWR:LȴVHOHFW\RXU:LȴQHWZRUNDQGHQWHU
your password.
PLAYBACK
The [PlayBack] includes common playback, sync playback, dayparting, smart
express, and smart search.
[Common PlayBack]: In the normal playback mode, you can select the channel,
period, date.
[Sync PlayBack]: Play back videos of multiple channels at the same time.
[Dayparting]: 3OD\EDFNWKHGLHUHQWWLPHYLGHRVRIDFKDQQHODWWKHVDPHWLPH
[Smart Express]:ΖQWHOOLJHQWO\IDVWIRUZDUGWKHVSHFLȴHGȴOHW\SH
[Smart Search]:ΖQWHOOLJHQWO\SOD\EDFNWKHVSHFLȴFȴOHW\SH
ALERT SETTING
The [Alert] includes intelligent alert, abnormality, and traditional alarm.
[Intelligent Alert]: Set the human detection or motion detection.
The human body motion detection function is enabled by default. You can set
human detection or motion detection in the area.
9 10
[Abnormality]: Analyze and inspect the current software and hardware of the
device. When an abnormal event happens, the device will give a response, such as
showing a message.
In the “Event Type”, you can select (No Storage/Storage Device Error/Storage No
'HYLFH1HW'LVFRQQHFWLRQΖ3&RQȵLFWWRHQDEOHDUHVSRQVH6KRZ0HVVDJH$OHUW
Mobile Reported/Sent Email) according to your needs.
[Traditional alarm]: Set the video blind, video loss and alarm input.
QUICK GUIDE FOR MOBILE
1. Make sure you have a router and high-speed network connection.
&RQQHFWWKH195WR\RXUURXWHUYLD:LȴRUXVLQJDQ(WKHUQHWFDEOH
3. Upgrade your client software and mobile app to the latest version.
4. Make sure your network speed comes up to 1Mbps at least to get the best
video recording.
Step 1: Download the “HomeViz” App.
Please download and install the “HomeViz” app on your phone by scanning the
below QR code or searching in the app store.
iOS Android
Step 2: Get a New Account.
Other Ways login
Cloud Login
Username
Password
Regiter Forget Password
11 12
Step 3: Scan the QR Code to Add Your Device.
[Device Name]: Input a name for your system.
[Serial Number]: To get the serial number, you can scan the QR code or go to
[Main Menu] →[Advanced] →[Version].
After you add the device, whenever you open
the “HomeViz” app, the device list window
below will be popped up. Tap the device you
want to view, then you can get the video from
all the connected cameras.
CONTACT US
For any inquiries with Dragon Touch products, please feel free to contact us.
We will respond within 24 hours.
E-mail: [email protected]
Tel: 888-811-1140 (US) Mon-Fri (except holidays) 9am-5pm (EST)
2ɝFLDOZHEVLWHZZZGUDJRQWRXFKFRP
13 14
Scan the following QR code or visit the Dragon Touch website to download the
user manual for more information.
USER MANUAL
English
www.dragontouch.com/manual/k4w10.pdf
QUÉ HAY EN LA CAJA
NVR × 1 Cámara de Seguridad × 4 Ratón × 1
Cable de Extensión
de Antena × 1
Cable de Red × 1Adaptador de Corriente × 5
Guía de Inicio Rápido × 1
V1.0
Quick Start Guide
Dragon Touch K4W10 HD NVR KIT
INTRODUCCIÓN
Panel Frontal del NVR
Panel Posterior del NVR
Salida de Audio
VGA
HDMI
RJ45
USB
DC
Puerto de Antena
Puerto de Antena
Antena
USB
Luces de Alarma
Luces de Potencia
Luces REC Botón OK Menú
ESC
15 16
Español
Table of contents
Languages:
Other Dragon Touch Security Camera manuals
