Arm
Release
Slider
Back Support
Release
Button
Release Button as
viewed from back
Release
Slider
Base
T-Bar
Securing Band
Pin
NOTE: ENSURE SECURING BAND IS FIXED ONTO PIN.
Securing Band
Pin
Securing Band
Pin
TO UNFOLD BATH SEAT
• Raise the Arm from under the Base
into the upright position (B) ensuring
that the Arm is secured at the
hinge point.
• Raise the Back Support away from
the base, insert the arm into the
back support and snap the button
into the slot provided (C).
TO USE
• Secure the seat to the bottom of the
bathtub by using the suction cups
on the Base of the seat.
• To open the bar, simultaneously
slide the ‘Release Slider’‚ buttons
away from the T-bar (D).
• With ‘Release Slider’‚ buttons
pushed back, open the T-bar (E & F).
• Position baby in the seat.
• To close the T-bar, position the
T-bar onto the Back Support and
snap under the ‘Release Slider’‚
buttons (E).
• Ensure that the ‘Release Slider’‚
buttons are secured in the
CLOSED position.
TO FOLD AWAY FOR
EASY STORAGE
• Release the seat from the bath
by pulling the tabs on the suction
cups. This will allow the seat
to be lifted readily (G).
• DO NOT PULL THE SEAT UP FROM
THE BATHTUB BEFORE RELEASING
ALL OF THE SUCTION CAPS.
• Press ‘Release Button’‚ to free the
Arm from the Back Support (H & I).
• Rotate the Arm and secure back
into the underside of the Base
of the Seat (B.)
• Fold Back Support towards
the Base.
WARNING: ENSURE T-BAR IS
SECURED IN PLACE BEFORE USE.
GENERAL MAINTAINANCE:
• Always ensure ‘Release Buttons’‚
are secured in the CLOSED position
while the Baby Bath Seat is in use.
• Check to ensure that the plastic
pins under the release bar are firmly
in place.
• Wash in warm soapy water, and
air dry.
WARNING- Children have DROWNED
while using bath aids. This is NOT a safety device.
ALWAYS keep baby within arm’s reach.
NEVER leave baby in care of children.
B C D
E F G
J I H
A
SIDE 2SIDE 1
INSTRUCTIONS
Fold Away Bath Seat
F610
PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Read instructions carefully before use.
This is NOT a safety device.
SAFETY CHECK:
Check to ensure that the plastic pins under the release bar
are firmly in place.
Dream Baby® Fold Away Bath Seat makes bathing baby easier.
The front bar opens out making it easy to place baby in seat or lift
baby out.
©2007 Tee-Zed Products Pty Ltd
TEE-ZED PRODUCTS PTY LIMITED OR TEE-ZED PRODUCTS (N.Z.) LIMITED ACCEPTS NO RESPONSIBILTY FOR ANY LOSS OR DAMAGE SUFFERED BY
ANY PERSON AS A RESULT OF THE USE OR MISUSE OF THESE GOODS. IN THE CASE OF ANY DEFECT IN THE GOODS, TEE-ZED’S LIABILITY SHALL BE
LIMITED SOLELY TO REPLACEMENT OF THE DEFECTIVE GOODS.
Look for the Dream Baby® range of Soothers, Toys, Rattles,Childcare and Safety Products.
Made in Taiwan
Dream Baby
®
products by
Tee-Zed Products Pty Ltd
PO Box 2022
Bondi Junction NSW 1355
Australia
Tee-Zed Products (N.Z.) Ltd
PO Box 64013
Botany Town Centre Auckland
New Zealand
info@tee-zed.com.au
www.dream-baby.com
www.dream-babyblog.com
For all enquiries, please call customer service
Australia + 61 (0)2 9386 4000
New Zealand (09) 274 8788
WARNING Prevent drowning. Babies can drown in as little as 2.5cm (1 inch) of water.
ALWAYS bathe your infant using as little water as necessary.
WARNING Prevent drowning. Babies can drown even when other children are in or near
the bathtub.
DO NOT allow other children to substitute for an adult.
WARNING Prevent drowning.
USE ONLY on smooth surface. Suction cups will not stick to slip-resistant surface.
Product is suitable for children able to sit up unassisted (approximately 5 months of age).
Product is not suitable for children able to pull up to a standing position
who may attempt to climb out (approximately 10 months of age).
There is no substitute for adult supervision.
Do not use this product if any components are damaged or missing.
