dreambaby Phoenix Bed Rail F719 User manual

ASSEMBLY
INSTRUCTION MANUAL
IMPORTANT KEEP FOR FUTURE REFERENCE
• Not suitable for children under 18 months or over 5 years.
• Use only with children able to climb in and out of bed unaided.
• The bed rail should not be used as a substitute for a cot as it cannot provide
the same level of safety as a cot.
• Never use without the fixing devices firmly attached to the bed and mattress.
• This bedguard should not be used on a sleeping surface that is more than 60cm
from the floor.
• When the bed rail is fitted well it should touch the side of the mattress.
• When the bed rail is fitted well it should touch the side of the mattress.
• Not suitable for beds with recessed baseboards.
• Use only on Mattress: Width: 76-160cm / 30-63in, Depth: 10-25cm / 4-10in,
Length: 160-200cm / 63-78.75in.
Complies with Standards: BS7972-2001+A1-2009
PARTS
A 1 x Storage Bag
B 1 x Cover
C 2 x Bedrail Frames (J=Brackets)
D 2 x Linking Tubes (frame & base)
E 2 x Base Tubes
Phoenix Bed Rail
A
D E
B
C
F719
F761
WARNING
ASSEMBLY SUMMARY
C C
D
D
E E

HOW TO ASSEMBLE
1234
910
11 12
14 15 16
18 19
13
5
678
Open brackets (J) Feed Cover onto Frame (C)
Squeeze buttons in,
join both Frames (C) with 1 x Linking Tube (D)
Spread Cover (B)
over Frame (C)
Join Base Tubes (E+D+E) using
remaining Linking Tube (D)
Feed through bottom of Cover (B)
Squeeze buttons (E) Insert securely into Brackets (J)
To remove cover (B) for washing,
reverse assembly steps.
17
20

L
H H
I I
J
K
J
K
1. Pull down Brackets (J) until
they click and lock into position. 2. Slide Brackets (J) under mattress.
3.
Position bed rail (L) so there is a gap of at
least 25cm / 10in from both ends of bed.
HOW TO INSTALL
INSTALLATION
J
J
J
25cm
10in
25cm
10in
L
PARTS LIST
H Straps
I Anchors
J Brackets
K Tabs
L Bed rail
4. Slide Straps (H) under the mattress and out the other side. 5. Tighten Straps (H) so that
2 Anchor plates (I) are tight
and flat against the side of
the mattress.
H
H
HI
2
SAFETY ANCHORS
SECURELY HOLD BED RAIL IN PLACE
I
WARNING:
To prevent the risk of strangulation it is
essential to ensure that when the bedrail is
fitted into position, there is a gap of at least
25cm /10in between each end of the bed
and the corresponding end of the bedrail.
7. Once installed, check the bedrail
is properly fitted and secure.
6. Tuck in any excess
straps under mattress

F719.761-08.2018
CONTACT DETAILS
Tee-Zed acknowledges that its customers may be entitled to statutory consumer guarantees and does not seek to exclude or limit them.
These guarantees include that Tee-Zed’s products are of acceptable quality. This Tee-Zed product is for the specific purpose detailed in the
instructions and packaging and Tee-Zed considers use outside of that purpose to be abnormal use. To the maximum extent permitted by law,
Tee-Zed does not accept any liability for damage:
• arising from abnormal use of the products;
• caused by installation or removal of the products other than in accordance with the supplied installation and removal instructions; or
• arising under the law of tort or contract.
CARE & MAINTENANCE
• Regularly check bed rail to ensure it is assembled and fitted properly and securely. Adjust as required.
• Discontinue use if damaged, broken, or if parts missing.
• Any additional and replacement parts should be obtained from Tee-Zed Products.
• To remove cover for washing, reverse assembly steps.
• To wash cover: warm machine wash gentle cycle, air dry.
To clean other parts, wipe with damp cloth using mild detergent.
Dreambaby® products by
Made in Xiamen City, China.
©2018 Tee-Zed Products Pty Ltd
Tee-Zed Products Pty Ltd,
PO Box 2022,
Bondi Junction NSW 1355
Australia

[phone]

[e-mail]
www.dreambaby.com.au
Tee-Zed Products (N.Z.) Ltd
PO Box 64013,
Botany Town Centre Auckland
New Zealand
 [phone]
 [e-mail]
www.dreambaby.co.nz
Tee-Zed Products Ltd
PO Box 29227,
Dunfermline, KY12 2DN
United Kingdom
 [phone]
 [e-mail]
www.dreambaby.co.uk
To open: To release lock, simultaneously lift both Tabs (K) on bed rail brackets.
Swing bed rail (L) down. Confirm bed rail is locked when down
OPERATION
K
KL
L
To close:
Release Lock, Swing bed rail (L) up
against mattress until the 2 tabs (K)
click and lock into position.
Before positioning under mattress, you must rotate T-Bar 90º
T-Bar For use with Slat bed bases
1 2
3
4
K
L