dreambaby F828 User manual

14
IMPORTANT! READ AND FOLLOW THESE INSTRUCTIONS
CAREFULLY AND KEEP FOR FUTURE REFERENCE
EASY TO FOLLOW INSTALLATION STEPS
INSTALLATION
Ensure
the orientation
(direction)
of the product
matches the
door handle
with a round
handle base.
Tee-Zed Products Pty Ltd
PO Box 2022
Bondi Junction NSW 1355
Australia
 [phone]
 [e-mail]
www.dreambaby.com.au
Tee-Zed Products (N.Z.) Ltd
PO Box 64013
Botany Town Centre
Auckland New Zealand
 [phone]
 [e-mail]
www.dreambaby.co.nz
Tee-Zed Products Ltd
PO Box 29227
Dunfermline, KY12 2DN
United Kingdom
 [phone]
 [e-mail]
www.dreambaby.co.uk
Made in Dongguan, China.
©2019 Tee-Zed Products Pty Ltd
Look for the Dreambaby® range of Child Safety and Care Products.
Dreambaby® products by
Tee-Zed acknowledges that its customers may be entitled to statutory consumer
guarantees and does not seek to exclude or limit them. These guarantees include
that Tee-Zed’s products are of acceptable quality. This Tee-Zed product is for the
specific purpose detailed in the instructions and packaging and Tee-Zed considers
use outside of that purpose to be abnormal use. To the maximum extent permitted
by law, Tee-Zed does not accept any liability for damage:
• arising from abnormal use of the products;
• caused by installation or removal of the products other than in accordance with
the supplied installation and removal instructions; or
• arising under the law of tort or contract.
X.01
WARNING
ADULT ASSEMBLY REQUIRED.
KEEP SMALL PARTS AWAY FROM CHILDREN DURING ASSEMBLY.
There is no substitute for proper adult supervision.
This product is only a deterrent.
Discontinue use when child is able to open it.
Indoor use only.
Store these instructions safely out of reach of children during installations
1
INSTRUCTIONS
Lever Door Lock
F828
Patent Pending
No adhesive
No drilling
required
Lever Door Lock fits most lever style door
handles with a round handle base diameter of
up to 7.5cm / 3in.
Door handles must be removed for installation.
up to
7.5cm
3in
Loop
Tab
Locking
Catches
Tab

2 3
Unscrew the handle from the door on
the side you need to have access
blocked using the appropriate screw
driver or Allen key. Store all parts
safely.
NOTE: leave the far side door handle
(the door handle not being locked) in
place, do not remove.
Door should look similar
to this when handle is
removed.
To Engage
To Disengage
INSTALLATION OPERATION
Position the Lever Lock,
over the spindle and
existing screw holes.
Before screwing into place,
again test the Loop will fit evenly
over your door handle.
Check it is positioned so
the Loop will fit over the door
handle when assembled.
Ensure it is
horizontal
and level.
ADULT ASSEMBLY REQUIRED.
KEEP SMALL PARTS AWAY FROM CHILDREN DURING ASSEMBLY.
Spindle
23
Allen
KEY
Squeeze side Tabs on the Loop
and rotate up and over the
door handle until the Loop
locks into place past the
Locking Catches. Release
Tabs.
The Loop must not be able to
rotate down.
Squeeze in the Side Tabs on
the Loop and rotate down over
the door handle until the Loop
locks in the down position.
Release Tabs.
The Loop must not be able to
rotate up.
Note: The Loop locks in both the up and down position to
prevent children from Engaging or Disengaging the product.
When Lever Lock is Engaged in most cases you cannot open the
door from the opposite side of the door, so door handles on both
sides of door could be locked.
When blocking access to a room is not required, always ensure
this item is Disengaged to avoid being locked in a room.
Tabs
Loop
4
56
Allen
KEY