7
Do not sit or lean on the base. The base is meant
to support the materials being cut.
simply click the tool into the base 8
Only use the Dremel Moto-Saw in the base. Other
electric power tools are not intended to be used
with the base.
9
Start the tool and let the tool come to the right speed
under load.
Before beginning work on your project, make a few
practice cuts on scrap material.
HAND-HELD MODE
the tool from its base Aq
Aa While cutting in hand-held mode, make sure
As
EDGE GUIDE
Ad
This attachment can be used as a push stick or as an
The edge guide can be locked in place turning the fence
MAINTENANCE AND CLEANING
NO USER SERVICEABLE PARTS INSIDE.
PREVENTIVE MAINTENANCE PERFORMED BY
UNAUTHORIZED PERSONNEL MAY RESULT IN
INCORRECT CONNECTION OF INTERNAL WIRING AND
COMPONENTS WHICH COULD CAUSE SERIOUS
HAZARD.
SERVICE
a.
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
MACHINE-SPECIFIC SAFETY WARNINGS
SAFETY WARNINGS FOR JIGSAWS
a. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a “live” wire may
make exposed metal parts of the power tool “live” and
could give the operator an electric shock.
b. Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the workpiece by hand or against your body leaves it
unstable and may lead to loss of control.
c. Keep hands away from the sawing range. Do not
reach under the workpiece. Contact with the saw blade
can lead to injuries.
d. Apply the power tool to the workpiece only when
switched on. Otherwise there is danger of kickback
when the cutting tool jams in the workpiece.
e.
then pull the saw blade out of the cut only after
it has come to a standstill. In this manner you can
avoid kickback and can place down the tool securely.
f. Bent or
unsharp saw blades can break or cause kickback.
g. Do not brake the saw blade to a stop by applying
The saw blade can
be damaged, break or cause kickback.
h. Use suitable detectors to determine if utility lines
are hidden in the work area or call the local utility
company for assistance. Contact with electric lines
can lead to re and electric shock. Damaging a gas
line can lead to explosion. Penetrating a water line
causes property damage or may cause an electric
shock.
i. Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
j. Keep your workplace clean. Blends of materials are
particularly dangerous. Dust from light alloys can burn
or explode.
k. Always wait until the tool has come to a complete
stop before placing it down. The tool insert can jam
and lead to loss of control over the power tool.
l. Never use the tool with a damaged cable. Do
not touch the damaged cable and pull the mains
plug when the cable is damaged while working.
Damaged cables increase the risk of an electric shock.
GENERAL WORKING STAND SAFETY WARNINGS
a. Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments or changing accessories.
Accidental starting of the power tool is a cause of
some accidents.
b. Properly assemble the working stand before
mounting the tool. Proper assembly is important to
prevent risk of collapse.
c. Securely fasten the power tool to the working
stand before use. Power tool shifting on the working
stand can cause loss of control.
d.
surface. When the working stand can shift or rock, the
power tool or workpiece cannot be steadily and safely
controlled.
!
WEAR EAR PROTECTORS (exposure to noise can
cause hearing loss)
!
DO NOT WORK WITH MATERIALS CONTAINING
ASBESTOS (asbestos is considered carcinogenic)
!
TAKE PROTECTIVE MEASURES WHEN DURING
WORK DUST CAN DEVELOP THAT IS HARMFUL TO
ONE’S HEALTH, COMBUSTIBLE OR EXPLOSIVE (some
dusts are considered carcinogenic); wear a dust mask
and work with dust/chip extraction when connectable
SPECIFICATIONS
Model number ........MS20
Input
Voltage
18 mm
Throat depth250 mm
Stroke length8 mm
Weight
Use completely unrolled and safe extension cords with
a capacity of 5 Amps.
Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the tool.
GENERAL
6
tool is intended to perform precise straight and curved
Fence lock lever
Guide rail
Base
Dust port
Securing clamps
USE
!
DISCONNECT THE PLUG FROM THE POWER
SOURCE BEFORE MAKING ANY ASSEMBLY,
ADJUSTMENTS OR CHANGING ACCESSORIES. Such
preventive safety measures reduce the risk of starting the tool
accidentally.
DUST EXTRACTION
STATIONARY MODE
Using the tool in stationary mode gives you the freedom to
10
