ducci XTREM DO 22 Guide

Dukab Yapı Malzemeleri San.ve Tic.Ltd.Şti
Instructions for Installation
Tüm Hakları Saklıdır.
XTREM DO 22
SLİDE SYSTEM

Before you start:
●WARNING: Please read these instructions carefully before starting the installation.
Incorrect installation may cause serious malfunctions during use. Always follow the
instructions and keep them for future reference.
●The shower enclosure is designed to allow an adjustment of 20 mm when installed on
nonparallel walls”.
●When you are ready to start, make sure you have the correct tools, plenty of space, and a
clean and dry area for installation.
●It takes two people to install the product. Although these instructions are extensive, please
remember that it is recommended to have the product installed by a technically competent
installer.
●Make sure to install the shower enclosure on a flat shower try or floor and on vertical walls.
●Attention: The dowels provided with this product are for ceramic walls only. Plasterboards
or erected walls may require fixing tools that are not provided. (Always make sure that the
dowels and connectors are suitable for the wall type.)
●Attention: Please hold all the glass parts carefully. Any damage on the edges or any
scratches on the surface occurred during installation or normal use may cause the glass to
break suddenly. Tempered glass will break into very small pieces that would still have sharp
edges.
●Attention: Be careful when drilling the wall so as not to damage hidden pipes or power
cables.
●When working near a shower tray or bathtub, make sure it is covered to prevent small
parts from falling into the drain.
Necessary Tools
Dukab Yapı Malzemeleri San.ve Tic.Ltd.Şti
2

Dukab Yapı Malzemeleri San.ve Tic.Ltd.Şti
3
Installation
1. Adjust two wall profiles on the
edge of the shower tray to ensure
that there are even not less than 10
mm. Use a water gauge to ensure
that both of them are vertical.
2. Making sure you do not move
the wall profiles, use a marker to
mark the hole points on the wall. Use
a drill it suitable for the wall type to
drill the holes. Use a plastic hammer
to insert the dowels into the holes
drilled.
Min & Max
Min & Max

Dukab Yapı Malzemeleri San.ve Tic.Ltd.Şti
4
3. In an empty area, place fixed
glasses into the channels of rail
profiles and glass profiles. To create
the frame, fix the glass profiles onto
the ends of the upper and lower rail
profiles with screws.
4. Insert the glass profile on both
sides into the wall profiles.
Note: For glasses with pattern, always
make sure that the pattern is on the
outside.
Installation

Dukab Yapı Malzemeleri San.ve Tic.Ltd.Şti
5
5. On the frame you just created,
align the holes on the wall profiles
with the dowels in the holes on the
walls, and use screws to fix them on
the wall.
6. After inserting and adjusting
the profiles, drill the glass and wall
profiles and fixed them to each other
with screws. Insert the screw caps.
Installation

Dukab Yapı Malzemeleri San.ve Tic.Ltd.Şti
6
8. On the upper section, insert
the bearing wheels into the rail
channel. On the lower section, press
on the spring-loaded pin to insert the
bearing rings into the profile channel.
Adjust the height using the pin screws
on the upper bearings.
7. Remove the screws on the
bearings, put them in the holes on
the glass and tighten the screws.
Installation

9. Insert magnetic seals onto the door glass.
Turn the adjustment screws on the bearings to
make sure that they get into contact in a way that
there is no gap between the seals.
Installation method for
water sealant
Dukab Yapı Malzemeleri San.ve Tic.Ltd.Şti
7
10. After the adjustments of magnetics and doors
are complete, you should place the stopper into
where the bearings are and attach it to the profile
with a help of a screw.
Installation of bearings
Installation

Dukab Yapı Malzemeleri San.ve Tic.Ltd.Şti
8
12. Once installation is done, apply silicone
sealant on the connection points outside
the shower enclosure.
Note: Before installation, make sure that
the environment is absolutely clean and
dry.
11. Thread the handle pins through
the holes in the glass of door, and
tigthen the screws to fix it.
Installation

Dukab Yapı Malzemeleri San.ve Tic.Ltd.Şti
9
After the installation
13. The product must not be used for the following 24 hours after the installation,
therefore once the installation is done, '' DO NOT USE'' scalant must be applied to the
shower enctosure , where it can be easily seen
14. The brand label must be applied to the desired area by removing the anti adhesive.
15. Do not forget to keep warranty certificate included in the package of product.
Note: The warranty certificate is valid tor two years.
24
DON'T USE FOR HOURS!
www.ducci.com.tr [phone]

Ömerli Neigh. Burçhan Street No:15/1
Hadımköy / İstanbul / Türkiye
T : [phone]
[phone]
F : [phone]
[email protected] / www.ducci.com.tr All rights reserved.
FACTORY - CENTRAL