ducduc STUDIO DUC JUNO PLAYTABLE User manual

juno playtable
a how-to guide that won’t leave you in tears
ASSEMBLY INSTRUCTIONS

parenting is hard.
this is easy.
no really, it is.
MADE HERE™
MADE SAFE MADE SMART
MADE WELL™

want to watch this assembly IRL?
(acronym challenged? that means “in real life”.)
open the camera on your phone and place it over the
QR code below to see our NYC studio dream team do all
the heavy lifting (just kidding, there is none!)
or go to ducducnyc.com/assembly-instructions

thank you for selecting a
studio duc product!

Please check contents against the components list in these in-
structions. Also, please ensure there was no damage that may
have occurred in shipping.
If any components are missing or you find any damage, please
contact ducduc before continuing.
Read all the instructions before use.
MAINTENANCE:
Please remember to securely tighten all connectors, and
periodically check to make sure every component is properly and
securely in place.
CLEANING:
Clean the white laminate surface periodically with cloth. Do not
scratch or chip the finish. Do not use abrasive chemicals for
cleaning. Clean non-laminate surfaces with mild soap on a soft
rag. Rinse and dry thoroughly. If you ever refinish this furniture,
be sure to use only a non-toxic finish specified for children’s furni-
ture.
KEEP INSTRUCTIONS FOR FUTURE USE

WHAT’S IN THE BOX:
A (x2)
side
E (x8)
side
F (x4)
seat
G (x4)
stretcher
B
top
C
center stretcher D
hammer cap
INCLUDED WITH PLAYSTOOL PURCHASE ONLY:

WHAT YOU’LL NEED:
household hammer
10 minutes
(or less)
2 people + a dog for moral support
(unless you’re a cat person)

1Lean A against the wall.
Insert B connectors into slots on A.
2
*duc insider tip*
Make sure the holes in B are
facing in- this is the underside of
the playtable and the holes are
where the center stretcher will be
attached.
*duc insider tip*
Steps in this assembly will require parts to
be flat on the floor.
Assemble on a soft surface to prevent any
damage. Try a rug, a blanket, or even a
sheet of foam from the packaging!

Push B down to lock connectors into place.3
Insert connector on C into remaining slot on A.4

Gently push C toward B so the connectors line up with the holes.
5
*important note*
Make sure NOT to push C in all the way. Have a friend
hold C in place while you prepare for the next step.
If C is not held in place, it can drop to the floor +
splinter the connection.

6Insert connectors on B + C into the slots of remaining part A.
*duc insider tip*
This is a bit of a balancing trick- but don’t stress!
We find it easiest to line up C’s connectors with
A’s slot first. Once that is in place, then line up B’s
connectors with A’s slots!

Push B down to lock connectors into place.
7

Flip the playtable so the legs are facing up as shown. Apply the hammer cap (D) to the end
of your own hammer. Tap C with the protected hammer until there is no gap at the seam to
secure into place.
8
*duc insider tip*
Don’t be afraid to apply a good amount
of force when hammering the stretchers
into place- as long as you use the
hammer cap the stretcher edge will be
protected! We recommend 2-3 strong
taps in focused locations (try both ends
and the center of the stretcher to start).

presto! playtable complete!
CONTINUE FOR PLAYSTOOL ASSEMBLY

1Lean E against the wall.
Insert F connectors into slots on E.
2
*duc insider tip*
Make sure the holes in F are
facing in- this is the underside of
the playstool and the holes are
where the center stretcher will be
attached.
*duc insider tip*
Steps in this assembly will require parts to
be flat on the floor.
Assemble on a soft surface to prevent any
damage. Try a rug, a blanket, or even a
sheet of foam from the packaging!

Push F down to lock connectors into place.
3
Insert connector on G into remaining slot on E.4

Gently push G toward F so the connectors line up with the holes.
5
*important note*
Make sure NOT to push G in all the way. Have a friend
hold G in place while you prepare for the next step.
If G is not held in place, it can drop to the floor +
splinter the connection.
6Insert connectors on F + G into the slots of remaining part E.
*duc insider tip*
This is a bit of a balancing trick- but don’t stress!
We find it easiest to line up G’s connectors with
E’s slot first. Once that is in place, then line up F’s
connectors with E’s slots!

Push F down to lock connectors into place.
7
Flip the playstool so the legs are facing up as shown. Apply the hammer cap (D) to the end
of your own hammer. Tap G with the protected hammer until there is no gap at the seam to
secure into place. Repeat steps 1 - 8 to complete the remaining 3 stools.
8
*duc insider tip*
Don’t be afraid to apply a good amount
of force when hammering the stretchers
into place- as long as you use the
hammer cap the stretcher edge will be
protected! We recommend 2-3 strong
taps in focused locations (try both ends
and the center of the stretcher to start).

okay, now you’re really done!
give yourself a pat on the back, take a bow,
or go house a pint of ice cream…we don’t judge.

prefer to talk to a human instead?
we’re here for you!
contact our customer advocate team below
212.226.1868
live chat at
ducducnyc.com
200 lexington, no. 701
ny, ny 10016
[e-mail]