Dundalk LeisureCraft 580S User manual

Ph: 519-923-9813 | E: [e-mail]| Web: www.dundalkleisurecraft.com
RB-01 2 Shower Half Moon Floor Section
RB-02 2 Long Floor Support
RB-03 2 Short Floor Support
RB-04 32 Standard Shower Staves
RB-05 1 Narrow Shower Stave
RB-06 4 Short Bottom Staves 12”
RB-07 4 Short Top Staves 8”
RB-08 2 Door Side Staves
AB-5 2 5’ Aluminum Shower Bands with Hardware
PL-1 1 Shower Drain Plug
Model 580S - Rainbow Outdoor Barrel Shower
Parts Identification & Assembly Instructions
RB-08
AB-5
RB-04
RB-03
RB-01
RB-02
RB-05
RB-06
RB-07
PL-1

Ph: 519-923-9813 | E: [e-mail]| Web: www.dundalkleisurecraft.com
Packaging
84” x 45” x 24” 430 lbs
213cm x 114cm x 61cm 195kgs
Model 580S - Rainbow Outdoor Barrel Shower
Parts Identification & Assembly Instructions
80”
203cm
60”
152cm
60”
152cm
24”
61cm
Economy Shower
Hardware
(Cold water Only)
Platinum
Shower Hardware
(Hot & Cold)
(Full stainless steel with hand held shower)
Optional Shower
Hardware

Ph: 519-923-9813 | E: [e-mail]| Web: www.dundalkleisurecraft.com
1. Using a clean and level area for assembly, place
both Floor Sections (RB-01) on the level ground.
RB-01
Model 580S - Rainbow Outdoor Barrel Shower
Parts Identification & Assembly Instructions
2. Line up the Floor Sections (RB-01) and screw
together in the pre drilled holes.
*Make sure the ends are flush
RB-01
3. Place the Long Floor Supports (RB-02) against
the guide and secure to the assembled floor with
screws.
Repeat for the outside Short Floor Supports on the
outside guides.
* Ensure supports are centered and not covering
the outside Bessel.
RB-02
RB-03
4. Flip over the assembled floor.

Ph: 519-923-9813 | E: [e-mail]| Web: www.dundalkleisurecraft.com
5. Insert the drain into the hole in floor
and tighten firmly.
Model 580S - Rainbow Outdoor Barrel Shower
Parts Identification & Assembly Instructions
6. Attach the Short Bottom Staves to the sauna floor
across from where the drain plug is located..
7. Continue to add the short bottom
staves using a rubber mallet if needed
to ensure they are tight.
8. Attach the left door stave (RB-08).

Ph: 519-923-9813 | E: [e-mail]| Web: www.dundalkleisurecraft.com
9. Attach the right side door stave.
Model 580S - Rainbow Outdoor Barrel Shower
Parts Identification & Assembly Instructions
10. Continue to attach staves around the shower
ensuring they are tight together.
Use a rubber mallet if required.
11. Attach the stave with the holes for the shower
head assembly adjacent to the floor drain.
* It will have one hole for the economy shower
head and 2 holes for the premium shower head
assembly (as shown )

Ph: 519-923-9813 | E: [e-mail]| Web: www.dundalkleisurecraft.com
Model 580S - Rainbow Outdoor Barrel Shower
Parts Identification & Assembly Instructions
13. When you get to the last staves, they will
be slightly bent outwards, this is normal.
14. Tap the last staves together until the shower
starts to take the right shape.
12. Continue to attach staves around the shower
ensuring they are tight together.
Use a rubber mallet if required.

Ph: 519-923-9813 | E: [e-mail]| Web: www.dundalkleisurecraft.com
Model 580S - Rainbow Outdoor Barrel Shower
Parts Identification & Assembly Instructions
16. Secure with provided screws.
17. Carefully unwrap the aluminum shower bands.
Bring the ends of the band together and connect
with the threaded rod and nuts. Hand tighten only.
Slide one of the aluminum bands over the top of
the shower.
15. Fit the short top stave assembly in between
the left and right door sides.

Ph: 519-923-9813 | E: [e-mail]| Web: www.dundalkleisurecraft.com
Model 580S - Rainbow Outdoor Barrel Shower
Parts Identification & Assembly Instructions
18. With a helper, wrap the second band around
the bottom of the shower and connect the ends in
the same manner as the top band.
Make sure the bands are 2” from the top and
bottom all the way around the shower.
Using a wrench or impact driver, tighten each
band a little at a time, starting with the bottom.
Tighten the band in stages- bottom first then top.
Work around the shower, hitting each stave with a
firm tap on the bottom band, you will see each
stave sit a little tighter.
Follow the same procedure for the top band.
Use a wrench to ensure both bands are very
tight. Hearing the wood “creak” is common.
19. Attach the optional shower head assembly to
the shower according to the manufacturers
instructions.