DUNNER ECOPOWER INVERTER 9 Instruction Manual

ECOPOWER INVERTER 9
ECOPOWER INVERTER 14
ECOPOWER INVERTER 12
ECOPOWER

ECOPOWER

ECOPOWER

6.Gas leakage test must be done before and after installation.
ECOPOWER
1

ECOPOWER
2

ECOPOWER
3

ECOPOWER
4

ECOPOWER
5

ECOPOWER
6

ECOPOWER
7

ECOPOWER
8

ECOPOWER
9
0~-30℃
P26 Low ambient temperature protection
valve Adjusted by technicians
1:yes

ECOPOWER
10

ECOPOWER
11

Inspection before use
A. Check installation of the whole machine and the pipe connections
according to the pipe connecting drawing;
B. Check the electric wiring according to the electric wiring diagram and
earthing connection;
C. Make sure that the main machine power switch is off;
D. Check the temperature setting;
E. Check the air inlet and outlet.
Trial
A. The user must “Start the Water circulation Pump before the heat pump and Turn off the
Heat pump before the water circulation pump”, or the heat pump will be damaged;
B. The user should start the heat pump, check for any leakage of water; and then
set suitable temperature in the thermostat, and then switch on power
supply;
C. In order to protect the swimming pool heater, the machine is equipped
with a time lag starting function, when starting the machine, the blower
will run 1 minutes earlier than the compressor;
D. After the swimming pool heater starts up, check for any abnormal noise
from the machine.
Precautions
A. Set proper temperature in order to get comfortable water temperature to
avoid overheating or overcooling;
B. Please don’t stack substances that can block air flow near inlet or outlet
area, or the efficiency of the heater will be reduced or even stopped;C.
Please don’t put hands into outlet of the swimming pool heater, and
don’t remove the screen of the fan at any time;
D. If there are abnormal conditions such as noise, smell, smoke and
electrical leakage, please switch off the machine immediately and contact
the local dealer. Don’t try to repair it yourself;
E. Don’t use or stock combustible gas or liquid such as thinners, paint and
fuel to avoid fire;
F. In order to optimize the heating effect, please install heat preservation
insulation on pipes between swimming pool and the heater. During
running period of the swimming pool heater, please use a recommended
cover on the swimming pool;
G. Connecting pipes of the swimming pool and the heater should be =10m,
or the heating effect of the heater cannot be ensured;
H. This series of machines can achieve high efficiency under air temperature
of +15?~+25?.
ECOPOWER
12

ECOPOWER
13

ECOPOWER
14

1.Check the water supply device and discharge often. You should avoid the condition
lack of water or air entering the system, as this will affect performance and reliability
of the unit. You should clean the pool/spa filter regularly to prevent damage to the filter.
unit as a result of dirt from the clogged filter.
2,The area around the unit must be dry, clean and well ventilated. Clean the exchanger
side heating periodically to maintain good heat exchange and save
Energy .
3.The operating pressure of the cooling system should only be repaired by a technician
certificate .
4.Check the power and cable connection often. In the event that the unit
starts to work abnormally, please turn it off and contact the technical personnel
skilled.
5.Discharge all the water from the water pump and water system so that freezing
of the water in the pump water system does not occur. You must discharge the water in
the bottom of the water pump if the unit will not be used for a long period of time.
6.You must check the unit thoroughly and fill the system with water completely
before using it before re-strat the heat pump which not use for a long period of time.
7.Before starting work on systems containing flammable refrigerants, make the necessary
security checks that are necessary to ensure that the risk of contact is
minimum.
ECOPOWER
15

ECOPOWER
PARA MAS INFORMACION O DESCARGAR ESTE
MANUAL DE FORMA DIGITAL ESCANEA EL CODIGO QR O INGRESA A LA
PAGINA
https://www.dunnerpool.cl/manuales-y-videos/