Duplex Jet Vac Eco User manual

JET VAC ECO
JET VAC ECO
ENGLISH
1 DUPLEX (UK)

JET VAC ECO
INTERPRETATION OF THE SYMBOLS PLACED ON THE UNIT
BEFORE USING THE STEAM GENERATOR, READ AND FOLLOW THIS INSTRUCTION MANUAL.
IT IS RECOMMENDED TO KEEP THIS INSTRUCTION MANUAL TO CONSULT IT LATER OR TO GIVE IT TO THE
FOLLOWING OWNERS.
PLEASE READ THE SAFETY INSTRUCTIONS ON THIS HANDBOOK BEFORE PROCEEDING ON THE FIRST USE.
EVENTUAL DAMAGES DUED TO THE CARRIAGE MUST BE COMUNICATED AS SOON AS POSSIBLE TO YOUR
OWN RETAILER.
ATTENTION!!
STEAM…. BURNING DANGER
ATTENTION !
READ THE OPERATING MANUAL
OPRATING MANUAL;
OPERATING INSTRUCTIONS
2 DUPLEX (UK)

JET VAC ECO
ENVIRONMENT PROTECTION
ALL THE PACKINGS ARE RECYCLABLE, PACKINGS DO NOT HAVE
TO BE THROWN IN THE DOMESTIC WASTE BUT THEY HAVE TO BE
DELIVERED TO THE CENTERS SPECIALIZED FOR THE DISPOSING
OF THE WASTE.
ALL DEVICES NOT USED ANYMORE CONTAIN PRECIOUS
RECICLABLE MATERIALS THAT SHOULD BE DELIVERED TO THE
CENTERS SUITABLE FOR THE DISPOSING OF THE W ASTE.
ELECTRIC AND ELECTRONIC EQUIPMENT, BATTERIES, OIL AND
SIMILAR SUBSTANCES MUST BE RECICLED IN THE PROPER
RECICLING CENTERS AND MUST NOT BE LEFT IN THE
ENVIRONMENT.
SUBSTANCES SUCH AS OIL FOR MOTORS, DIESEL OIL, PETROL
MUST NOT BE LEFT IN THE ENVIRONMENT AND MUST BE
RECICLED IN THE PROPER RECICLING CENTERS ACCORDING TO
THE ENVIRONMENTAL REGULATIONS.
3 DUPLEX (UK)

JET VAC ECO
1. SUMMARY
1. SUMMARY 4
2. SAFETY REGULATIONS 4
3. TECHNICAL CHARACTERISTICS 6
4. PREFACE 6
5. TECHNICAL DRAWINGS 7
6. NOMENCLATURE 11
7. OPERATING INSTRUCTIONS 12
8. MAINTENANCE 13
9. BEFORE REFERRING TO THE TECHNICAL SERVICE 16
10. DECLARATION OF CONFORMITY 17
2. SAFETY REGULATIONS
The electric supply connection shall be made by a qualified electrician and comply with IEC
60364-1.
It is recommended that the electric supply to this machine should include either a residual
current device that will interrupt the supply if the leakage current to earth exceeds 30ma for
30ms or a device, which will prove the earth circuit.
SAFETY VALVE
This machine is equipped with two safety valves, able to ensure the safety
of the machine itself in case other primary control devices are inefficient (due to a fault). Due
to the extreme importance of these components and as not to compromise the safety of the
machine, it is recommended to provide to check them and to substitute them through an
authorized service center by 1.500 hours of usage or once a year, starting from the
purchasing date.
PRESSURE SWITCH
This machine is equipped with a pressure switch able to check and to
maintain the pressure under certain preset limits (ref. “rated pressure” on the technical label
underneath the machine). In case there would be a steam leak on the lower side of the
machine, it means that the functioning of this device has been compromised and the safety
valve has been involved as to limit the boiler internal pressure.
It is recommended not to
use the machine, immediately unplug the machine from the power feeding and call the
service center.
MUD DRAIN FROM THE BOILER
If you are not acquainted with the hardness level of the
used water, it is recommended to proceed with the boiler cleaning (according to the
4 DUPLEX (UK)

JET VAC ECO
procedure indicated in the proper section) after 24 hours of usage. On the contrary, if you
know the hardness level and it is between 0 and 4 french degrees , the boiler cleaning can be
carried out after 100 hours of usage.
ATTENTION.
Do not use the appliance within the range of persons unless they wear
protective clothing.
ATTENTION.
Pressure jets can be dangerous if subject to misuse. The jets must not be
directed at people, live electrical equipment, or the machine itself.
Do not direct the jet against yourself or others in order to clean clothes or footwear.
Disconnect power before effectuating maintenance on user’s responsibility.
Steam cleaners shall not be used by children or untrained personnel.
To ensure the machine safety, use only original spare parts from the manufacturer or
approved by the manufacturer.
ATTENTION.
Pressure hoses, fitting and couplings are important for the safety of the
machine. Use only those recommended by the manufacturer.
Do not use the machine if the power cord or other important parts of the machine are
damaged, i.e. safety devices, pressure hoses and trigger gun.
If an extension cord is used the plug and socket must be of watertight construction.
ATTENTION.
Inadequate extension cords can be dangerous.
The user must not leave the iron (optional) unattended when it is connected to the power
supply.
The hand-arm vibration data, referred to this device, are not mentioned as they are below 2.5
m / s ².
5 DUPLEX (UK)

JET VAC ECO
3. TECHNICAL CHARACTERISTICS
To verify the technical data of your model, consult the plate under the appliance.
4. PREFACE
Dear Client,
We would like to congratulate you on your choice.
Please consider that the machine before leaving our factory has been tested and tweaked by
qualified and specialized personnel.
With the goal of improving and continually updating production by always offering innovative
products, TECNOVAP has studied, designed and created the
JET VAC ECO
; a combined
machine for cleaning which brings together the power of steam and the force of vacuuming.
This product is equipped with a dependable stainless steel boiler with automatic refilling system
which allows it to produce a powerful and continuous supply of steam (24/24 hours).
The
Jet Vac Eco
is the ideal solution when it comes to cleaning and disinfecting. With
the various accessories available, it cleans, disinfects, and removes dirt eliminating completely
even the bacterial flora hidden in those areas most difficult to reach.
6 DUPLEX (UK)

JET VAC ECO
5. TECHNICAL DRAWINGS
7 DUPLEX (UK)

JET VAC ECO
8 DUPLEX (UK)

JET VAC ECO
9 DUPLEX (UK)

JET VAC ECO
10 DUPLEX (UK)

JET VAC ECO
6. PARTS LIST
1) Powercord steam generator 42) Turbo lance steam –steam & vac
2) “Low water” indicator (red) 43) Small nylon brush (Ø 28mm)
3) “Ready steam” indicator (green) 44) Small brass brush (Ø 28mm)
4) Power switch 45) Small stainless steel brush (Ø 28mm)
5) Boiler switch 46) Triangular brush
6) Steam outlet 47) Steam plunger
7) Handle bar steam generator 48) Steam scraper
8) Steam generator 49) Large nylon brush (Ø 60mm)
9) Water tank 50) Stainless steel wool pad
10) Electric socket for vacuum cleaner (20) 51) Floor tool (steam and steam & vac) for inserts
11) Water tank cap 52) Latches for blocking inserts
12) Vacuum drum 52A) Cloth clamps
13) Vacuum hose outlet 53) Insert squeegee/brush (L.375mm)
14) Locking latch vacuum outlet 54) Insert squeegee/squeegee (L.375mm)
15) Fixing for vacuum unit 56) Steam and steam & vac window cleaner
16) Fixing for vacuum head 57) microfibre cloth for window cleaner
17) Handle bar vacuum cleaner 58) Carpet tool –transparent
18) Vacuum switch 59) Steam & vac lance
19) Electronic regulation vacuum head 60) Upholstery tool
20) Power cord vacuum cleaner 61) Insert squeegee/squeegee (L.145mm)
21) Locking nut for separator 62) Insert squeegee/brush (L.145mm)
22) Separator 62A) Insert stainless steel/stainless steel (L. 145mm)
23) Grill protection for separator 63) Insert brush/brush (L.145mm)
24) Fixing screw for grill protection for separator 64) Large stainless steel brush (Ø 60mm)
25) Anti-allergens Hepa filter (optional) 65) Insert squeegee/brush (L.300mm)
26) Conveyor cap 66) Carpet insert
27) Trolley
67) Insert stainless steel/stainless steel (L.375mm)
28-29) Cestino porta accessori 68) Long lance
30) Flexible vacuum hose 69) Triangular brush
31) Steam plug locking latch 70) Curved bayonette lance 45°
32) Steam plug 71) Bayonette lance
33) Steam and steam & vac hose with handgrip 72) Stainless steel steam scraper
34) Security trigger for steam outlet 73) Triangular steam buffer
35) Water command switch (intermittent) 74) Rectangular steam buffer
36) Steam adjustment switch (minimum) 80) Professional steam iron
37) Steam adjustment switch (medium) 81) Thermostat
38) Vacuum switch 82) Steam switch
40) Clamping latches for accessories 83) Rubber rest pad
41) Extension tubes
11 DUPLEX (UK)

JET VAC ECO
7. OPERATING INSTRUCTIONS
(a)
After opening the packaging box eventually fix the machine on the trolley.
(b)
Plug the power cord (20) into the electric socket (10) and verify that the vacuum power switch (18) is in ON
position.
(c)
Lift the tank cap (11) and add water to the water tank,
we recommend to exclusively fill in water only, any
other liquid may damage the generator permanentely
.
(d)
Insert the plug (1) into an electrical outlet, making sure that the voltage and the amperage correspond with those
printed on the plate of the machine (on the inferior part).
WARNING
WHEN THE W ATER TANK IS EMPTY THE LOW WATER INDICATOR (2) SW ITCHES ON AND THE STEAM
OUTPUT WILL BE DISABLED UNTIL WATER IS BEING ADDED TO THE WATER TANK (9).
PLEASE NOTE: THIS OPERATION CAN BE CARRIED OUT W ITHOUT SW ITCHING OFF THE MACHINE.
USE OF THE ACCESSORIES
Insert the vacuum hose (30) into vacuum hose outlet (13) and the steam plug (32) into the steam outlet (6) found
on the front of the machine. Push until the latches (14 and 31) lock into place.
Activate the power switch (4) and the boiler switch (5) for the production of steam and wait approximately 5
minutes until the green "ready steam" indicator (3) on the command switch lights up indicating that the boiler has
reached the operating pressure. The switches (35,36 and 37) located on the handle should be in OFF position.
When the indicator (3) lights up, position the switches (36 and 37) on the handgrip to regulate the steam flow as
follows: switch (36) minimum flow, switch (37) medium flow, switches (36) and (37) maximum flow. Use the security
trigger (34) to activate the steam flow.
The vacuum switch (38) activates the vacuum and can be used simultaneously with steam, the power can be
regulated by pressing the + and –symbols on the electronic regulation (12) on the vacuum head.
The switch (35) enables you to inject overheated water with the steam by activating it for a few seconds at a time
to avoid exceeding the injected liquid to the steam.
To clean with the combination of steam, injection of overheated water and vacuum suction choose the accessory
best suited for the job:
Warning!!
By pushing the switch (35) overheated water under pressure with a temperature, according to the model, of
up to 180 °C will come out of the lance. Please be careful not to action this switch without alert and do not
align the jet towards persons or animals.
To clean with the combination of steam, injection of overheated water and vacuum suction choose the accessory
best suited for the job:
The multi-purpose floor tool (51): with appropriate inserts (53,54,66,67). Inserts are locked into place by sliding the
latches (52) to the OPEN position and hold the insert in place applying a little pressure while sliding the latches in
12 DUPLEX (UK)

JET VAC ECO
BLOK position. Mount the floor tool onto the hand grip or on the extension tubes and lock everything by sliding the
latches (40) to the BLOCK position. Remember that the command switches on the handle (35-36-37-38) must be on
OFF position up to the completing of this operation.
Turbo lance steam/vac (42): to be used by itself or with the small included brushes or with the steam plunger (47)
and the steam scraper (48) according to the cleaning job to be executed.
For mounting this tool please follow the above instructions of the floor tool.
When finished cleaning, it is recommended to vacuum approximately 3-5 litres of clean water to rinse the inside of
the hose (33) and the suction conduits. W ash and dry all accessories used. Remove the vacuum drum (13) and,
after emptying and rinsing it, let it dry before storing it away.
If you are using the brushes of the Kit July (steam only) the bristles can be covered with an absorbing cloth by
using the clamps (52A) to hold the cloth in place. This is a recommended use to clean delicate surfaces (such as
precious wood for ex.) or vertical surfaces (in tiles for ex.) etc. The cloth is acting as dirt "extractor" in this case.
8.
MAINTENANCE
ATTENTION
DISCONNECT FROM ELECTRICAL POWER SUPPLY BEFORE CARRYING OUT USER MAINTENANCE. IT IS
RECOMMENDED THAT BOILER MAINTENANCE IS CARRIED OUT WHEN THE EQUIPMENT HAS COOLED
DOWN. (SWITCHED OFF FOR AT LEAST 5 HOURS)
MAINTENANCE OF STEAM GENERATOR
ELIMINATING SCALE RESIDUE FROM THE BOILER
If you do not know the degree of hardness of the used water we suggest cleaning the boiler after every 24 working
hours, if the degree of hardness is known and lies between 0 and 4 french degrees the frequency can be varied to
100 hours of use.
Fill the water tank, place a recipient container under the machine and remove the boiler drain cap underneath the
machine. Then switch on the machine activating the power switch only (4) and let the water pump work for about 2
minutes, then switch off the machine (power switch 4) and unplug the power cord (1) from the electrical socket and
replace the boiler drain cap (6) . The process of cleaning is completed, once again plug the power cord (1) into the
electric outlet and activate the power switch (4). It is recommended to activate also the command switch (36) for
minimum steam on the handgrip and activating the security trigger (34) to release the air contained in the empty
boiler. Wait for the completed cycle of refilling from the pump (approx. 3 min.).
The maintenance of the boiler is completed; proceed with the using instructions as described in chapter 5.
13 DUPLEX (UK)

JET VAC ECO
MAINTENANCE OF THE VACUUM CLEANER
Control periodically the separator (22) through the grill protection and verify that there are no sediments or dirt that
sometimes can deposit on it.
If necessary proceed as follows: remove the screw (20A) and the protection grill (20) turning it counter clockwise
and pulling it down, unscrew the locking nut of the separator (21) and remove the separator (22). Proceed with the
cleaning of the separator (22) and remount everything by paying attention that the marking on the inside of the
separator is positioned correctly on the housing of the turbine.
14 DUPLEX (UK)

JET VAC ECO
MAINTENANCE OF THE ACCESSORIES
Clean and grease occasionally the connections of the hose extension and of the accessories.
PG5123
OR 29.82x2.62
PG5106
OR 9.25x1.78
PG5116
OR 6.75x1.78
15 DUPLEX (UK)

JET VAC ECO
9. BEFORE REFERRING TO THE TECHNICAL SERVICE
PROBLEM
POSSIBLE CAUSE
REMEDY
MACHINE DOES NOT
LACK OF POWER. MAKE SURE PLUG IS WELL INSERTED (1)
PRODUCE STEAM AND
AND THAT THERE IS MAIN POWER TO THE
VACUUM DOES NOT WORK.
OUTLETS.
THE RED "LOW WATER"
ALL THE WATER HAS BEEN CONSUMED. REFILL THE WATER TANK (5A) WITH
INDICATOR (2) LIGHTS UP.
CLEAN WATER.
SUCTION POWER IS MISSING. A. LACK OF POWER TO THE
A. C) MAKE SURE THE SWITCH (18) IS
VACUUM CLEANER.
ON AND THE PLUG (20) IS WELL
INSERTED. (10)
B. THE VACUUM TUBE IS
OBSTRUCTED.
B. B) CLEAN TUBE AND ACCESSORY
USED.
C. THE VACUUM DRUM (12) IS
FULL OF WATER.
C. EMPTY THE VACUUM DRUM (4).
WATER LEAKS THROUGH THE
CHECK THE WEAR OF THE
CLEAN AND LUBRICATE THE O-RING WITH
CONNECTIONS OF THE
GREASE.
O-RING.
ACCESSORIES.
IF NECESSARY, REPLACE WITH ONE
SPARE SUPPLIED.
STEAM DOES NOT COME OUT. A. BOILER HAS NOT REACHED YET
A. WAIT A FEW MINUTES.
THE OPERATIONAL PRESSURE
B. SWITCH ON THE STEAM
(GREEN LIGHT (3) IS OFF).
COMMAND SWITCHES (36-37).
B. STEAM COMMAND SWITCHES (36-
C. USE THE STEAM COMMAND
37) ARE OFF.
SWITCH (34) TO ACTIVATE THE
A) THE STEAM COMMAND SWITCH (34)
STEAM FLOW..
HAS NOT BEEN USED..
DROPS OF WATER COME OUT
AT BEGINNING OF WORK WATER
AFTER A FEW MINUTES OF USE THIS
CONDENSES IN THE TUBES AND
OF THE ACCESSORIES
PROBLEM WILL CEASE. IF IT CONTINUES,
ACCESSORIES DUE TO THE
DIFFERENCE IN TEMPERATURE.
PROCEED TO THE CLEANING OF THE
BOILER.
NOISE INSIDE THE GENERATOR. WHILE COOLING DOWN, THE BOILER,
WAIT FOR THE PRESSURE STABILIZATION
AFTER 6-7 HOURS, IS CREATING AN
(ABOUT 2-3 MINUTES), THE NOIS
INTERNAL DEPRESSION, WHICH AT EACH
DISAPPEARS.
IGNITION, PROVOCES SOME VIBRATIONS..
ACCESSORIES DO NOT FIT
THERE IS DIRT BUILD UP IN THE JOINTS
CLEAN AND LUBRICATE THE JOINTS.
PERFECTLY
AND LOCK/RELEASE LATCHES (40).
16 DUPLEX (UK)

JET VAC ECO
10. DECLARATION OF CONFORMITY
DICHIARAZIONE DI CONFORMITA’ CE
(EC DECLARATION OF CONFORMITY)
TECNOVAP S.R.L.
con la presente
dichiara che:
le macchine per pulizia a vapore modello:
(Certifies that the steam cleaning machine model):
Carmen Mini
Risultano conformi
alle specifiche delle direttive
(conforms to the specifications of directives)
2002/95/CE
2006/95/CE 2004/108/CE 2006/42/CE
Per il controllo della conformità alle sopraindicate direttive, sono stati seguiti i seguenti standard
:
(For the chec king of c onformity to the above directives, the following standards have been used):
Riferimento alle norme armonizzate:
(Reference to harmonized standards):
EN 60335
-
1
EN 60335
-
2
-
2
EN 60335
-
2
-
79
EN 60335
-
2
-
3
EN 55014
-
1
EN 55014
-
2
EN
61000
-
3
-
2
EN
61000
-
3
-
3
PESCANTINA
–
VERONA (ITALY)
02
-
02
-
20
10
FRANCHINI Giuliano
(Managing Director)
17 DUPLEX (UK)

JET VAC ECO
Ordinary maintenance procedures
Working hours
Frequency
Notes
Generator
Intervention
18 DUPLEX (UK)

JET VAC ECO
Extraordinary maintenance procedures
Working
Date of
Intervention, description, replaced components, etc.
hours
Intervention
Generator
19 DUPLEX (UK)

JET VAC ECO
THE MANUFACTURER RESERVES THE RIGHT TO PRODUCE TECHNICAL AND STRUCTURAL
IMPROVEMENTS W ITHOUT PRIOR NOTICE
20 DUPLEX (UK)