DURASTEEL Work Table User manual

Work Table Assembly Instructions
1
4. Adjust Plastic Feet
All four legs can be adjusted for surfaces that
aren’t completely level. Rotate the plastic foot pad
to compensate for differences in floor surface.
4
3
3. Fasten legs to leg sockets
Using Allen wrench and screws to fasten legs to
leg sockets. Then, turn the whole unit upside, and
it is ready to use!
2
2. Insert legs to leg sockets
Place carton underneath tabletop for padding to
avoid scratching. Please insert the legs into leg
sockets.
1. Assemble undershelf and legs
Marking the position on the legs by tape for the
height of the undershelf (Recommend at least 8”
above the floor). Slide legs into the socket of
undershelf, then, fasten the Allen screws.
1
Unpack and check to make sure all contents are complete.
Please follow the steps and instructions below.
Top Shelf (1)
Lower Shelf (1)
Legs (4)
Allen Screws (16)
Allen Wrench (1)
1
2
3 4
5

2
View Products
Pick following link by your
country and exchang ASIN to
product ASIN code.
For example: amazon.com/dp
/B08JGMZ7T3
Make sure to select the size &
spec you like.
US
amazon.com/dp/ASIN
Canada
amazon.ca/dp/ASIN
Mexico
amazon.com.mx/dp/ASIN
Related Products
Caster
ASIN
B07RJRXFYJ
Maple Wood
Tabletop
ASIN
B08N4CYJSN
Open Base Work
Table Bracing
ASIN
B0BFVXD7LX
Undershelf
ASIN
B088K6WKSF
Hairpin Legs
Two Colors Optional
Stain Black & Raw Steel
7 Sizes Optional
6”, 12”, 16”, 20”, 28”, 34”, 40”
ASIN
B07RQJ8565
Various Work Tables
w/ U-Shaped
Bracing
ASIN
B0BHZDG14J
w/ Die Cast Corner
Brackets
ASIN
B07T9JRN3M
Cart Table
ASIN
B07KPBBFLH
w/ Backsplash
ASIN
B07RP5Y2L1
w/ Undershelf
ASIN
B0BH97M848
• Stainless Steel • Maple Wood
Stainless Steel Cart Tables and Other Stainless Steel Tables are the same height, 34 inches. If a higher cart table is
needed, we recommend you purchase a worktable without casters and purchase additional casters to switch bullet feet.
In order to uphold the longevity of the DuraSteel stainless steel worktable. It should be wiped
down after every use and periodically cleaned with a non-abrasive mild detergent. Please refer
to our Stainless Steel Care and Cleaning Instructions.
Warning
Purchase from
Our response will be in English
Contact Us
amzn.to/2Twy8Dk amzn.to/2PuT0 amzn.to/2w7Cueb
Follow
US
@durasteel @DuraSteelUSA

© 2023 DuraSteel All Rights Reserved
Troubleshooting
The hardware is missing. How can I get a replacement?
Please refer to Page 2 to contact us. We will send a replacement screw set to you.
Why is the surface of the table blue or white?
The blue or white is the protective film. Please remove the film before using it.
Can I purchase additional undershelf?
Yes, you can. We do carry undershelfs from 12” to 72”. Please order them by referring to Page 2.
Can I add casters to the worktable?
Yes, you can. We do carry caster wheels from 3” to 5”. Please order them by referring to Page 2.
How to switch bullet feet to casters?
First of all, please remove the bullet feet. You can use a slotted screwdriver or plier to remove bullet feet,
or disassemble the table top and slide a long pole into the opening end of the leg, and then push the foot
until it is removed. After you remove the bullet feet, please follow the instruction below to assemble.
A Method
This is the main method. Insert the caster into the leg; if the rubber part is too large for the socket, please
loosen the top nut (A) by moving it counter clockwise. Once the stem is successfully inserted into the leg,
please use a wrench to tighten nut (B) by moving it clockwise until the caster is firmly secured inside the leg.
*If nut B doesn’t work and the caster cannot stuck in the leg, please use B method to assemble.
B Method
Please use a wrench to turn the gear toward the rubber to squeeze and expand the rubber until it is about
the same size as the feet socket. Simply insert the caster into the foot socket. When the caster is upside,
tighten it by moving the base clockwise. Since they are about the same size now, it will get stuck inside
the leg.
Why stainless steel is magnetic?
Not all, but a lot of stainless steel products are magnetic. There are many of the 430 stainless steel are
magnetic due to the anti-corrosive element added to the alloy.
How to maintain my stainless steel products?
Please refer to our Stainless Steel Care and Cleaning Instructions to maintain
your stainless steel products. If the packing doesn't include this sheet, please
download it via the link below or scan the QR code on the right hand.
Download Link http://bit.ly/3Ydwzwu
Nut (B)
Nut (A)
A Method
Gear
Base
B Method