Durite O-649-70 User manual

Call 01255 555200
Email [e-mail]
Visit www.durite.co.uk
DURITE’s innovative 12/24v Super Capacitor Jump pack. Super light and compact with capability to jump start all petrol
vehicles and diesel vehicles with upto 16.0L engine capacity. For both 12v and 24v application this product outputs 500A
Starting Current and 1200A Peak Current. Intelligent LCD display shows state of charge and vehicle battery health status. CE
approved.
Parts List:
1 x 12/24v Super Capacitor Jump Pack
1 x 230v UK Charger
1 x 12v In car charger
1 x User Manual
O-649-70 12/24VDC Jump Starter Pack
TECHNICAL SPECIFICATIONS
THE TRUSTED QUALITY BRAND FOR PROFESSIONALS

WARNINGS!
Before using this unit please read these in-
structions carefully
.
Take special care to follow the warnings and
safety suggestions listed throughout this
manual.
Keep these instructions for future reference.

1. Check before using the product that there is at least 60% charge state. If there is not do not attempt to start the
vehicle until the unit is fully charged.
2. Do NOT crank the engine for more than 3 seconds using the product.
3. Please wait at least 2 minutes before trying to crank the engine again if it does not start.
4. Make sure the voltage is selected before connecting to a vehicle battery.
5. Do not connect the RED Clamp to the earth terminal on battery and vice versa as this will lead to short circuit. It
could damage the product and further be dangerous to the user.
6. Remove the jump starter immediately on starting the vehicle.
7. Always check that the jumper clamps are connected correctly. Check the vehicle battery terminals to ensure they
are not rusty/dirty. If so clean before attempting to connect and jump the vehicle.
8. If the vehicle does not start on the third attempt please do not try again as this will damage the unit and will void
the warranty.
9. If the unit enters its 'protected state' please press and hold the 'power' button to reset the unit.
10. This unit has no serviceable parts inside. Please do not try to open/dissemble the unit as this could be
dangerous and will void the warranty.
11. MUST NOT BE USEDTO JUMP START ANY VEHICLE WITH A LITHIUM ION BATTERY INSTALLED - RISK OF
DAM-AGE OR INJURY!
12. Do not use the unit if it has been dropped or damaged.
13. Do not charge for more than 1.5 hour charging USB 5V3A. If charging from car battery remove after 3 minutes.
14. Jump for 12V/24V vehicles only. It is forbidden to use for other machines such as aircraftship and so on.
15. DO NOT use this unit if any cable clamp or cord is damaged.
16. DO NOT use in place of a vehicle battery.
17. DO NOT use as a battery charger.
18. Do NOT operate the product in explosive atmospheres, such as in the presence of flammable liquids, gases or
dust.
19. Do NOT expose product to extreme heat or fire.
20. Make sure someone is within range of your voice or close enough to come to your aid when working with
batter-ies.
21. Remove personal metal items like rings, bracelets, necklaces, etc. When using the products.
22. Do NOT store in locations where the temperature may exceed 60°C
23. Charge only at ambient temperature between 0°C and 45°C.
24. Charge only using the charger provided with this unit.
25. Do NOT use the unit to jump start a vehicle while charging the internal battery.
26. If this unit is leaking liquid dispose of at a proper recycle facility immediately.
27. Under extreme conditions, battery leakage can occur. If a liquid is noticed coming from product do not handle
with bare hands. In case of skin contact wash with soap and water immediately. If liquid comes in contact with eyes
rinse eyes with cold running water for at least 10 minutes and get medical attention immediately.
28. Product contains super capacitor, at end of product life dispose of product according to local regulation.

PRODUCT LAYOUT
CHARGING
1. Connect the USB cable with the UK plug or 12V cigarette charger and then plug it into the
5V3A socket shown above. Follow instructions per state of charge on the LCD screen. Remove
from charge once fully charged. Use appliance immediately to benet from full cranking ability
from the full charge stored in the capacitors.

OPERATION GUIDE
Check the power status of the jump starter by pressing the power SWITCH (shown page be-
fore)
Assess the vehicle voltage by connecting the RED to +VE terminal and BLACK clamp to -VE
terminal.The unit should auto select the correct voltage.
When the starter can not recognize the correct voltage, you must manually press the corre-
sponding voltage button.
Attention: When using a 12V battery to power up a 24V vehicle, you must manually press the
24V button when the product is fully charged, then the product will continue charging to the
voltage required for starting 24V vehicle.
When charging via the 5V3A Socket:
1. Fully charge the jump pack, the voltage is 27V when the jump pack in full power.
2. Connect the RED clamp to the vehicle’s battery positive(+) terminal and connect the BLACK
clamp to the vehicle’s battery negative(-) terminal.
3. When the host display “XXX V”+ “Jump START READY”, start the car.
4. Start the vehicle.
5. When the vehicle is started, remove the jumper from the vehicle battery
When charging via the vehicle battery:
1. Connect the RED clamp to the vehicle’s battery positive(+) terminal and connect the BLACK
clamp to the vehicle’s battery negative (-) terminal.
2 .The jump pack automatically recognizes the corresponding 12V/24V model based on the
vehicle battery voltage. It will stop charging when charging to 13.5V/27V and displayes “Jump
START READY”.
3.Start the vehicle.
4 .When the vehicle is started, remove the jump pack from the vehicle battery.
Attention: please don’t charge for product when the battery voltage <1 OV.
When you can’t start the vehicle, please follow the steps as below and resolve it appropriate:
1 .Refer to the owner’s manual to determine the battery voltage and ensure that the jump
packs output voltage is correct.
2.Turn off the vehicle ignition, switch and all accessories (lights, radio, etc.)
3. Ensure that the RED clamp is connected to the vehicle’s battery positive(+) terminal
and connect the BLACK clamp to the vehicle’s battery negative(-) terminal
4 .Press the voltage button that matches your vehicle for about 2 seconds.
5.The screen will display “XX.X V”+ “Jump START READY” according
to the selected voltage.
6 .The product will output for 30 seconds after automatic recognition / forced output (the
screen display “jump start ready“). Please start the car within 30 seconds
7. If the above operation still can not start the car, please conrm if the current product voltage
is consistent with the vehicle battery voltage. If the current product voltage is around 13V and
the vehicle battery voltage is 21V, it needs to press the 24V button, then try above operation
when the jump pack voltage reaches 27V.
8. If the above has been fullled then the vehicle will need to be inspected by a professional
who can assess the vehicle for the further fault.

LED ash light
1. Press the switch 3 seconds to start the LED ash light.
2.There are 4 modes of LED light, cycle through in order by pressing button lightly (normal,
strobe, SOS, off).
Toxic and Harmful Substances in 0-649-70
Vehicle BatteryTest Function:
First, connect the RED clamp to the vehicle's battery positive(+) terminal and connect the
BLACK clamp to the vehicle’s battery negative(-) terminal.Then the jump pack will determine
whether the vehicle battery needs to be charged or replaced by detecting voltage and resist-
ance.
When the battery voltage <12V and resistance<50mOhms, the screen displays NEED RE-
CHARGE.
When the resistance >50mOhms, the sreen display REPLACE BATTERY.
When the battery voltage <24V and resistance<100mOhms, the screen will display NEED RE-
CHARGE.
When the resistance>100mOhms, the screen will display REPLACE BATTERY.

Call 01255 555200
Email [e-mail]
Visit www.durite.co.uk
TECHNICAL SPECIFICATIONS
The information contained in this document is correct to the best of our knowledge and subject to change at any time without notice.
TECHNICAL SPECIFICATIONS
Type Jump Starter Pack
Capacity 720F x 10 Super Capacitor
Battery Cell N/A
Output Voltage 12/24VDC
Start Current.. 500A
Peak Current. 1200A
Charge lnput.. 5V3A (or 5V2A / 5V1A)
Full ChargingTime 1.5 Hours (5V3A), 3 Minutes Vehicle Battery
OperatingTemperature -40°C to 55°C
Dimensions 295*220*111mm
Weight 2.650KG
Certifcation CE