Duronic RCD017 User manual

OPERATING INSTRUCTIONS
MODEL : RCD017
DIGITAL MICRO
CD-RADIO HI-FI SYSTEM
CAUTION
DO NOT EXPOSE TO DRIPPING
OR SPLASHING LIQUIDS!
NOTE: CAUTION SYMBOLS ARE PRINTED ON REAR OF UNIT. PLEASE REFER TO
INSTRUCTION MANUAL.
E-2
CAUTION: INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
VORSICHT: UNSICHTBARE LASERSTRAHLUNG TRITT AUS,
WENN DECKEL GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT IST. NICHT DEM STRAHL AUSSETZENI.
VARNING: OSYNLIG LASERSTRÁLNING NÄR DENNA DEL ÄR ÖPPNAD OCH
SPÄRR ÄR URKOPPLAND. STRÁLEN ÄR FARLIG.
ADVARSEL: USYNLIG LASERSTRÁLING VED ÁBNING. NÁR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÁ UDS/ETTELSE FOR
STRÁLING.
ATTNENZIONE: RADIONS LASER INVISIDILE. NON GUARDARE
DIRETTAMENTE NELLA SORGENTE DEL LASER.
ACHTUNG: LASERLINSE NICHT BERÜHREN UNSICHTBARER LASERSTRAHL.
AVISO: A LENTE NUNCA DEVE SER TOCADA.
PLEASE NOTE: YOU WILL FIND THE
RATING LABEL FOR THIS PRODUCT
LOCATED ON THE BOTTOM OF THE UNIT.
CAUTION: GROUNDING OR POLARIZATION. THE PRECAUTIONS SHOULD BE TAKEN
SO THAT THE WIDER BLADE OF THE AC PLUG MUST MATCH THE SLOT IN
RECEPTACLE "WALL SOCKET".
CLASS 1 LASER P RODUCT
KLASSE 1 LASER P RODUKT
LASER DE CLASSE
LASER DI PRIMA CLASSE
KLASSE 1 LASER
LASER P RIMERA C LASE
LASER CLASSE 1
KLASSE 1 LASER P RODUKT
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO DRIPPING OR SPLASHING LIQUIDS.
THE MAINS PLUG IS USED AS TH E DISCONNECT DEVICE AND IT SHALL REMAIN
READILY OPERABLE. TO COMPLETELY DISCONNECT THE POWER INPUT, TH E
MAINS PLUG OF THE APPARATUS MUST BE DISCONNECTED FROM THE MAINS
COMPLETELY. THE MAINS PLUG SHOULD NOT BE OBSTRUCTED OR SHOULD BE
EASILY ACCESSED DURING INTENDED USE.
The lightning flash and arrowhead within the triangle is a warning sign
alerting you of "dangerous voltage" inside the product.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
To reduce the risk of electric shock, do not remove cover (or back). No
user-serviceable parts inside. Refer servicing to qualified service personnel.
CAUTION:
The exclamation point within the triangle is a warning sign alerting you of
important instructions accompanying the product.
THE APPARATUS SHOULD NOT BE EXP OSED TO DRIPPIN G OR SPLAS HING AND NO OBJE CTS
FILLED WITH LIQUIDS SHOULD BE PLA CED ON THE APPARATUS.
UNDER THE INFLUENCE OF ELE CTROSTATIC PHEN OMENON, THE PRODUCT MAY
MALFUNCTION AND USER TO POWER RESET.
BATTERY SHALL NOT BE EXPOSED TO EXCESSIVE HEAT SUCH AS SUNSHINE, FIRE OR
THE LIKE.
CAUTION
DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH
THE SAME OR EQUIVALENT TYPE.
THE MARKING AND RATING LABE L IS LOCATED AT REAR ENCLOSURE OF THE APPARATUS.
DATE : 06 FEB., 2015 (R1)
SC-0008/15
JOB-00215-0006
MODEL NO.: Z117-P2FM3U “DURONIC_RCD017”
ENGLISH IM FOR APPROVAL
SIZE : 100 (W) x 135 (H) MM (each page)
MATERIAL : 80G WOODFREE PAPER
PRINTING COLOR : BLACK

E-4
CONNECTION OF SPEAKER BOXES
- UNWRAP THE SPEAKER-CORDS OF BOTH SPEAKER-BOXES AND INSERT THE
LEFT/RIGHT PLUGS INTO SOCKETS IN THE REAR OF MAIN UNIT.
- PLACE THE SPEAKER BOXES AS FAR APART AS POSSIBLE FOR BEST SOUND
EFFECT.
POWER SUPPLY
- THIS SET WORKS ON NORMAL HOUSEHOLD AC-POWER.
- INSERT THE PLUG OF THE AC-CORD INTO A WALL OUTLET WITH AC-POWER.
- PRESS THE ON/ STANDBY KEY TO SWITCH “ON” THE UNIT.
- THIS UNIT IS DESIGNED TO OPERATE WITHOUT EVER BEING TOTALLY POWERED
"OFF". IT WILL EITHER BE "ON" OR "STANDBY MODE".
- WHEN IN STANDBY MODE, YOU CAN USE THE ON/ STANDBY KEY TO SWITCH "ON"
THE UNIT.
- TO CONSERVE ELECTRICITY, PLEASE SWITCH THE UNIT TO "STANDBY MODE"
WHEN NOT LISTENING TO RADIO OR CD MUSIC.
INTELLIGENT POWER SAVING SYSTEM
- THIS SET HAS A BUILT-IN POWER SAVING SYSTEM WHICH WILL AUTOMATICALLY
PUT THE SET INTO A "STANDBY MODE" TO REDUCE POWER CONSUMPTION
WHEN IT DETECTS THAT THE SET IS NOT IN USE.
- THIS AUTOMATIC SWITCHING TO "STANDBY MODE" WILL HAPPEN
APPROXIMATELY 10-15 MINUTES AFTER THE FOLLOWING CIRCUMSTANCES:
(A) "CD" MODE: CD PLAYBACK HAS STOPPED (eg. AT THE END OF A DISC).
(B) "AUX" MODE: NO INPUT SIGNAL IS DETECTED AT THE AUX INPUT JACK.
(C) "USB" MODE: USB PLAYBACK HAS STOPPED.
- TO RE-ACTIVATE THE UNIT AFTER IT HAS AUTOMATICALLY SWITCHED TO
"STANDBY MODE", SIMPLY PRESS THE "ON/ STANDBY" KEY TO SWITCH ON THE UNIT.
HEADPHONE JACK
- THIS UNIT IS EQUIPPED WITH A STEREO HEADPHONE JACK (3.5MM DIAMETER)
WHICH ACCEPTS MOST STANDARD EARPHONES & HEADPHONES (NOT INCLUDED).
- WHEN THE PLUG OF A STANDARD STEREO HEADPHONE (OR EARPHONE) IS
INSERTED INTO THIS JACK, THE SPEAKERS WILL AUTOMATICALLY BE DISABLED.
- WHEN THE HEADPHONE/EARPHONE IS DISCONNECTED, THE SPEAKERS WILL BE
RE-ACTIVATED.
1
1
5
23
14
13
97 8
6
15
16
17
18 19 20 21
1. SPEAKERS (LEFT/RIGHT)
2. POWER LED LIGHT
3. LCD DISPLAY
4. USB SOCKET
5. ON/ STANDBY KEY
6. FUNCTION KEY
7. MEM./ PROG./ P-MODE KEY
8. FM RECALL/ +10/ FOLDER KEY
9. PLAY/ PAUSE KEY
10. STOP/ SNOOZE/ SLEEP KEY
11. NEXT/ TUNE+ KEY
E-3
LOCATION OF CONTROLS
12. BACK/ TUNE- KEY
13. VOLUME + / CLOCK SET KEY
14. VOLUME - / ALARM SET KEY
15. CD DOOR
16. CD DOOR FINGER-GRIP
17. FM-ANTENNA WIRE
18. AUX INPUT SOCKET
19. SPEAKER OUTPUT SOCKETS
(LEFT & RIGHT)
20. HEADPHONE SOCKET
21. AC-CORD & PLUG
4
10 11 12

DIGITAL CLOCK FUNCTION
- THE SET HAS A BUILT-IN DIGITAL CLOCK, WHICH IS DISPLAYED WHEN THE UNIT IS
IN "STANDBY MODE" OR WHEN YOU PRESS & HOLD MEM./ PRO G. KEY
FOR TWO SECONDS DURING CD OR RADIO OPERATION.
- TO SET THE CORRECT TIME, FOLLOW THIS PROCEDURE:
HOW TO SET CORRECT TIME:
SWITCH UNIT TO "STAND-BY" MODE
PRESS & HOLD FOR 3 SECON DS
DISPLAY SHOWS HOUR OR HOUR (FLASHING)
CLOCK SET KEY
12 24
PRESS NEXT OR BACK TO SELECT 12-HOUR OR 24-HOUR CLOCK
DISPLAY SYST EM & PRES S CLOCK SET TO CONFI RM YOUR SELECTI ON
PRESS NEXT OR BACK REPE ATEDLY TO SET THE CORREC T
MINUTE IN THE DISPL AY & PRES S TO CONFI RMCLOCK SET
PRESS NEXT OR BACK REPE ATEDLY TO SET THE CORREC T HOUR
IN THE DISPL AY & PRES S CLOCK SET TO CONFI RM
CORREC T TIME IS NOW SET & WIL L BE SHOWN IN THE DISPL AY!
E-5
AUTOMATIC POWER OFF SLEEP FUNCTION
- THIS SET HAS A SPECIAL SLEEP TIME R FUNCTION WHICH CAN AUTOMATICALLY
SWITCH OFF THE UNIT. THIS IS USEFUL FOR SLEEPING TO MU SIC AT NIGHT.
- AT ANY TIME WHILE THE UNIT IS OPERATING, PRESS AND HOLD 2 SECONDS
KEY REPEATEDLY TO CHOOSE THE AUTOMATIC OFF TIME.
SLEEP
90
MINS
80
MINS
70
MINS
60
MINS
50
MINS
(*OFF MEANS SLEEP TIMER IS DEACTIVATED)
OFF*
40
MINS
30
MINS
20
MINS
10
MINS
E-6
ALARM FUNCTION
HOW TO SET ALARM
- THIS SET HAS A TIMER FUNCTION TO ENABLE YOU TO PROGRAM THE UNIT TO
AUTOMATICALLY SWITCH “ON” AT PRESET TIMES. THIS IS USEFUL AS A MORNING
ALARM CLOCK :
1. PRESS AND HOLD ALARM SET KEY . THE ALARM SYMBOL APPEARS IN THE DISPLAY.
2. PRESS NEXT OR BACK TO ADJUST THE HOUR OF THE DESIRED "ON" TIME
AND THEN PRESS ALARM SET KEY TO CONFIRM.
3. PRESS NEXT OR BACK TO ADJUST THE MINUTES OF THE DESIRED "ON" TIME
AND THEN ALARM SET TO CONFIRM.
4. NOW THE DISPLAY WILL INDICATE THE "WAKE UP MODE" (RADIO/ CD/ USB/ BUZZ).
PRESS NEXT TO CHOOSE THE DESIRED MODE & PRESS ALARM SET TO CONFIRM.
5. THE DISPLAY THEN SHOWS THE "WAKE UP VOLUME LEVEL" (LOUDNESS).
PRESS BACK OR NEXT TO DECREASE OR INCREASE THE VOLUME LEVEL TO BE
USED FOR THE MUSIC TO BE PLAYED WHEN THE TIMER SWITCHES ON THE UNIT
AT THE PRE-SET TIME.
6. PRESS ALARM SET TO CONFIRM.
7. FINALLY THE UNIT WILL RETURN TO THE NORMAL DISPLAY, EXCEPT THAT THE ALARM
SYMBOL WILL BE SHOWN, TO INDICATE THAT YOU HAVE PROGRAMMED A ON ALARM
SETTING.
8. IN CASE YOU WISH TO DISABLE THE TIMER, PRESS THE ALARM SET KEY ONCE,
& THE ALARM SYMBOL WILL DISAPPEARS.
9. THE ALARM WAKE UP TIMER WILL AUTOMATICALLY TUNE OFF AFTER AROUND AN HOUR.
10. AT ANY TIME DURING ALARM WAKE UP, SIMPLY PRESS THE STANDBY KEY TO STOP
ALARM.
(NOTE : THE AUTOMATIC ON TIMER WILL SWITCH ON THE UNIT AS IF YOU HAVE MANUALLY
PRESSED THE “ON/ OFF” KEY. IF YOU HAVE SELECTED "WAKE TO RADIO", THE EXACT
PRESET RADIO BAND & STATION WILL BECOME ACTIVATED WHEN POWER SWITCHES ON).
SNOOZE FUNCTION
- WHENEVER THE ALARM ( ) COMES O N,
IT C AN B E TEMPORARILY SUSPENDED FOR A S HORT P ERIO D O F 9 M IN UTES,
BY P RESSING THE “ SNOOZE” K EY O NCE.
- THE ALARM ( TUNER (RADIO )/ CD/ U SB) W ILL THEN AUTOMATIC ALLY
COME O N AGAIN AFTER THE 9 M IN UTES “SNOOZE” P ERIO D H AS ENDED.
- THE PROCEDURE CAN B E R EPEATED TO APPROXIM ATELY AN H OUR.
TUNER ( RADIO)/ C D/ U SB
ELECTRONIC VOLUME CONTROL
- THIS UNIT USES AN ELECTRONIC VOLUME CONTROL .
- TO INCREASE OR DECREASE THE LOUDNESS OF UNIT, PRESS
THE VOLUME UP (VOLUME +) OR VOLUME DOWN (VOLUME -) KEYS RESPECTIVELY.
- RELEASE THE KEY WHEN VOL UME LEVEL IS AT THE DESIRED LOUDNESS.
- SOMETIMES, ESPECIALLY DURING LISTENING TO THE RADIO, YOU MAY NOTICE
A "CLICK-CLICK-CLICK" (REPEATING) SOUND WHEN YOU ARE INCREASING OR
DECREASING THE VOLUME. THIS IS A NORMA L CONDITION & THE SOUND WILL
DISAPPEAR WHEN YOU RELEASE THE VOLUME KEY (WHEN YOU REACH THE
DESIRED VOLUME LEVEL).
(PUSH BUTTON TYPE)
SWITCH UNIT TO “STAND-BY” MODE.

E-7
RADIO MEMORY (STATION PRESET MEMORY STORAGE)
- AT ANY TIME, THE CURRENTLY DISPLAYED STATION OR FREQUENCY CAN BE
STORED INTO ONE OF THE MEMORY POSITION.
- PRESS MEM./PROG. KEY ONCE.
- PRESS NEXT OR BACK KEY TO SELECT DESIRED MEMORY POSITION.
(THERE ARE 30 MEMORY POSITIONS).
- PRESS MEM./PROG. KEY ONCE TO SAVE THE SELECTED STATION INTO THE
SELECTED MEMORY POSITION.
- TO RECALL ANY SAVED MEMORY, SIMPLY PRESS THE FM RECALL KEY, THE SAVED
RADIO-BAND WILL BE RECALLED.
- TO CLEAR THE MEMORY OF ANY POSITION, SIMPLY SAVE A NEW STATION TO
THE SAME MEMORY POSITION.
OPERATION OF RADIO
- PRESS THE "ON/STANDBY" KEY ONCE TO SWITCH ON THE UNIT.
- PRESS THE FUNCTION KEY REPEATEDLY UNTIL THE DISPLAY SHOWS "FM".
- TO IMPROVE FM-RADIO RECEPTION, FULLY EXTEND THE FM-ANTENNA WIRE AND
ADJUST IT'S POSITION.
- USE THE “PLAY/ PAUSE” KEY TO SELECT THE DESIRED MODE (FM MONO/STEREO).
IN SOME CASES, WHERE RECEPTION IS POOR, IT MAY BE ADVISABLE TO SELECT
“MONO” MODE, TO IMPROVE CLARITY OF THE RADIO SIGNAL.
MANUAL FREQUENCY ADJUSTMENT (SCAN MODE)
- PRESS (AND IMMEDIATELY RELEASE) THE NEXT KEY OR BACK KEY TO “SCAN”
(MANUALLY ADJUST) THE RADIO FREQUENCY “UP” OR “DOWN” BY 1-STEP AT A TIME.
- THE RADIO DIGITAL DISPLAY WILL INDICATE THE EXACT FREQUENCY AT EACH
STEP’S POSITION.
- WHEN A DESIRED FREQUENCY OR STATION IS REACHED. IT CAN BE SAVED
INTO ONE OF THE “MEMORY” POSITIONS. (SEE “RADIO MEMORY” SECTION).
AUTOMATIC FREQUENCY ADJUSTMENT (SEEK MODE)
- PRESS AND HOLD (FOR 2 SECONDS) THE NEXT OR BACK KEYS TO “SEEK”
(AUTOMATICALLY ADJUST) THE RADIO FREQUENCY “UP” OR “DOWN” TO THE NEXT
AVAILABLE RADIO STATION.
- THE RADIO DIGITAL DISPLAY WILL INDICATE THE EXACT FREQUENCY OF THE
NEXT STATION THAT IS FOUND.
- WHEN A DESIRED STATION IS REACHED. IT CAN BE SAVED INTO ONE OF THE
“MEMORY” POSITIONS. (SEE “RADIO MEMORY” SECTION).
INSERTION & REMOVAL OF DISCS
- WHEN OPENING THE CD-DOOR, ALWAYS ENSURE THE DISC IS NOT IN MOTION
(NOT SPINNING) WHEN YOU OPEN THE CD-DOOR. ALWAYS PRESS “STOP” BUTTON
TO STOP THE DISC SPINNING FIRST.
- PLACE A CD INTO THE COMPARTMENT WITH THE LABEL-SIDE (PRINTED SIDE OF
DISC) FACING UPWARDS. PRESS DOWN IN THE CENTER PART OF DISC UNTIL THE
DISC “LOCKS” ONTO THE CENTER SPINDLE.
- WHEN THE CD HAS BEEN PLACED ONTO THE CENTER SPINDLE, GENTLY LOWER
THE CD-DOOR DOWNWARDS UNTIL IT LOCKS SHUT.
- THE CD IS NOW READY TO BE PLAYED.
E-8
NORMAL CD OPERATION
- PRESS "ON/STANDBY" KEY TO SWITCH ON THE UNIT.
- INSERT A CD AS DESCRIBED.
- PRESS THE "FUNCTION" KEY REPEATEDLY UNTIL THE DISPLAY SHOW S "CD"
- THE DISK WILL START SPINNING & THE FIRST SONG (TRACK) WILL START PLAYING.
THE DISPLAY WILL INDICATE THE CURRENT TRACK NO.
- AT ANY ANYTIME DURING PLAYBACK, PRESS THE PLAY KEY TO PAUSE OPERATION
OF THE UNIT. PRESS PLAY KEY TO RESUME OP ERATION AT THE SAME TRACK &
POSITION.
- AT ANYTIME DURING PLAYBACK, PRESS THE STOP KEY TO STOP OPERATION OF
THE SET. THIS WILL RESET THE SET TO THE FIRST TRACK (IF YOU PRESS
PLAY AFTER STOP, THE FIRST TRACK WILL ALWAYS START PLAYING).
- AT ANYTIME DURING PLAYBACK, PRESS AN D RELEASE THE NEXT OR BACK KEYS
TO SKIP FORWAR D OR BACKWARDS BY ONE TRACK, AS DESIRED.
- ANY ANYTIME DURING PLAYBACK, PRESS AND HOLD THE NEXT OR BACK KEYS
TO FAST-FORWAR D (CUE) OR FAST-REVERSE (REVIEW) THE SPECIFIC TRACK,
WHICH IS CURRENTLY PLAYING.
- TO REMOVE A DISC, FOLLOW THE SAME PROCEDURE AS DESCRIBED ABOVE,
EXCEPT TO REMOVE THE CD INSTEAD OF INSERTING IT INTO THE COMPARTMENT,
BY PLACING ONE FINGER AT THE MIDDLE OF DISC (CENTER SPINDLE) & THE
OTHER AT THE EDGE OF THE DISC & GENTLY PULLING UPWARDS.
- IMPORTANT : ALWAYS HOLD A CD BY ITS EDGES. AVOID GETTING ANY FINGER
PRINTS, SMUDGES OR DIRT ONTO THE SURFACE OF A DISC. IN CASE THIS
HAPPENS, USE A SPECIAL CD-CLEANING CLOTH OR CLEANING KIT TO REMOVE
THE DIRT OR SMUDGES.
- THE CD PLAYER CAN BE PROGRAMMED TO PLAY ANY SEQUENCE OF UPTO 20 TRACKS
FOR REGULAR CD-AUDIO DISCS & 99 TRACK FOR MP3, AS DESIRED.
- ALWAYS PRESS THE STOP KNOB BEFORE STARTING THE PR OGRAMMING.
- PRESS THE MEM./ PROG. KEY, THE DISPLAY WILL SHOW A MEMORY SYMBOL
AND THE DISPLAY WILL SHOW “ ” , TO INDICATE THAT THE SET IS NOW IN
"MEMORY PROGRAMMI NG MODE", AT MEMORY POSITION NO. 1.
- PRESS THE NEXT/BACK KEYS OR TO SELECT THE TRACK (SONG) NUMBER
YOU WISH TO BE STORED IN THE FIRST MEMORY (PROGRAM) POSITION, AND PRESS
THE MEM./ PROG. KEY TO CONFIRM YOUR SE LECTION.
- WHEN YOU PR ESS MEM./ PROG. KEY THE DISPLAY WILL ADVANCE TO THE NEXT
MEMORY POSITION NUMBER (EG. “ ” FOR 2ND POSITION).
- REPEAT THE PREVIOUS 2 STEPS, EACH TIME SELECTING ANY TRACK NUMBER OF
YOUR CHOICE TO BE STORED IN THE SUCCESS IVE MEMORY (PROGRAM) POSITIONS.
- AFTER EACH TRACK NUMBER, REMEMBER TO PRESS THE ME M./ PROG. KEY.
- AFTER A MAXIMUM OF 99 SONGS (OR LESS) HAVE BEEN SELECT ED AS DESCRIBED
ABOVE, PRESS THE PROGRAM KNOB.
- ALSO, THE MEMORY SYMBOL WILL REMAIN "ON" TO INDICATE THAT YOU
HAVE SAVED A PROGRAM- MEMORY (SEQUENCE).
- PRESSING PLAY WILL NOW PLAY BACK THE "SAVED SEQUENC E" IN
THE PROGRAM MEMORY.
- PRESSING NEXT/ BACK WILL MOVE TO THE NEXT OR PREVIOUS SONG
IN THE SAVED SEQUENC E.
- TO CLEAR (CANCEL) THE ENTIRE PROGRAM WHICH IS STORED IN THE MEMORY,
SIMPLY PRESS "STOP" TWICE, OR SWITCH "OFF" THE SET.
PROGRAMMING THE CD-PLAYER
P01
P02

E-10E-9
HOW TO PLAY MP3 DISCS
- INSERT A MP3 DISC INTO THE PLAYER AND CLOSE THE CD DOOR.
- PRESS “ON/ STANDBY” KEY TO SWITCH ON THE UN IT.
- PRESS THE “FUNCTION” LEY REPEATEDLY UNTIL THE DISPLAY SHOW “CD”.
- THE DISK WILL SPIN AND PERFORM A FULL CHECK OF THE DI SC TO COUN T THE TOTAL
NUMBER OF SONGS. THEN PLAYBACK OF THE FIRST SONG (TRACK) WILL BEGIN AND
THE DISPLAY WILL INDICATE THE CURRENT TRACK NO: (001).
- IF YOUR DISC HAS “FOLDER” (SEE BELOW) THE DISPLAY WILL SHOW THE F OLDER
NUMBER (eg. F01, etc..) EVERY 5 SECONDS.
- AT ANY TIME DURING PLAYBACK, PRESS AND RELEASE OR TO SKIP
BACKWARDS OR FORWARDS BY ONE TRACK.
- MP3 DISCS OFTEN CONTAIN GROUPS OF SONGS OR SEVERAL "FOLDER"
(SUB DIRECTORIES), YO U CAN USE THE + 10/ FOLDER KEY TO QUICKLY JUMP TO
A PARTICULAR SONG.
PRESS AND RELEASE TH E +10/ FOLDER KEY = SKIP +10
PRESS AND HOLD THE +1 0/ FOLDER KEY = REPEATEDLY TO CHOOSE THE FOLDER
- EACH TIME YOU PRESS THE +1 0/ FOLDER , THE PLAYER JUMPS
TO THE FIRST SONG IN THE NEX T FOLDER . (THE DISPLAY WILL ALTERNATE BETWEEN
THE SONG N UMBER & THE FOLDER NUMBER EVERY 5 SECONDS).
(NOTE: THE “FOLDER” FUNCTION ONLY WORKS ON MP3-DISCS WHICH HAVE FOLDERS.
USB- MP3 PLAYBACKDRIVE
PERCENTAGE (ABOUT 5%) OF USB FLASH DRIVES MIGHT NOT BE READABLE, DUE TO THOSE
USB-DRIVE MANUFACTURERS NON-COMPLIANCE WITH THE FULL (OFFICIAL) USB 1.1 / 2.0 STANDARDS.
ALTHOUGH THIS PRODUCT IS FULLY COMPATIBLE WITH USB 1.1 & 2.0 STANDARDS, A SMALL
NOTE:
THE READING TIME FOR A USB-DRIVE VARIES DEPENDING ON THE SPEED OF THE MEMORY DEVICE
AND THE NUMBER OF SONGS AND FOLDERS. IN SOME CASES THE READING TIME MAY BE AS LONG
AS 60 SECONDS.
ALWAYS SWITCH OFF THE UNIT OR CHANGE MODE TO “CD” OR “RADIO”BEFORE REMOVING A USB
FLASH DRIVE, TO PREVENT DAMAGE TO YOUR USB DEVICE.
IMPORTANT
- THIS UNIT IS EQUIPPED WITH A USB SOCKET WHICH CAN ACCEPT AND PLAY MP3
FILES STORED ON STANDARD USB FLASH DRIVES (ALSO KNOWN AS "PEN DRIVES")
WHICH ARE FOR MEMORY STORAGE. (COMPATIBLE WITH USB VERSION 1.1 & 2.0).
- TO UTILIZE THIS FACILITY, FIRST INSERT EITHER A USB-DRIVE INTO THE SLOT (PORT).
- PRESS THE FUNCTION KEY REPEATEDLY UNTIL THE DISPLAY SHOWS "USB".
- AFTER ABOUT 5-10 SECONDS THE DISPLAY WILL INDICATE THE NUMBER OF MP3
SONGS FOUND ON THE USB-DRIVE , AND ALSO THE NUMBER OF FOLDERS ON
THE DEVICE.
- PRESS THE +10/ FOLDER KEY REPEATEDLY TO SELECT THE DESIRED FOLDER NUMBER.
- PRESS NEXT OR BACK TO SKIP FORWARD OR BACKWARDS TO SELECT THE
DESIRED MP3 FILE IN THE SELECTED FOLDER.
- PRESS PLAY/PAUSE TO START PLAY BACK OF THE SELECTED SONG.
- ALL FUNCTIONS FOR USB-DRIVE ARE EXACTLY THE SAME AS IN CD-MP3 MODE
(AS PREVIOUSLY DESCRIBED).
SPECIFICATIONS
POWER SUPPLY : ................................... AC 100V-240V ~ , 50/60Hz
POWER CONSUMPTION : ....................... 15 W
SPEAKER : .............................................. 2.5” x 2
FREQUENCY : ........................................ FM 87.5 - 108 MHz
REPEAT PLAYBACK FUNCTION
- AT ANYTIME DURING PLAYBACK, PRESS KEY REPEATEDLY
TO SELECT:
= TO REPEAT THE CURRENT TRACK
= TO REPEAT ALL TRACKS (FULL CD)
= TO REPEAT ALL SONGS FROM CURRENTLY SELECTED
FOLDER(DIRECTORY)
= TO PLAY SONGS IN A RANDOM ORDER (SHUFFLE)
P-MODE
ALL
FOLDER
USING THE AUDIO LINE IN CONNECTION (AUX-INPUT)
- YOU CAN CONNECT THE AUDIO OUTPUT OF AN EXTERNAL DEVICE SUCH AS A MP3
PLAYER TO THIS UNIT, TO LISTEN TO THE SOUND OF THAT DEVICE THROUGH
THE HIGH QUALITY AMPLIFIER OF THIS MUSIC SYSTEM.
- TO CONNECT THE EXTERNAL DEVICE PLEASE USE THE STANDARD
STEREO HEADPHONE (3.5MM TO 3.5MM PLUGS) CABLE TO CONNECT THE
"HEADPHONE-OUT OR AUDIO LINE-OUT" OF THE DEVICE TO THE AUX-INPUT SOCKET
OF THIS UNIT.
- PRESS THE FUNCTION KEY TO SELECT "AUX" MODE.
- MAKE SURE THAT THE SPEAKERS ARE CONNECTED TO THE MAIN UNIT.
- SWITCH ON THE POWER OF THE MAIN UNIT AND THE EXTERNAL DEVICE
(eg. MP3-PLAYER).
- START PLAYBACK OF THE EXTERNAL DEVICE AND ADJUST THE VOLUME CONTROL
OF THE MAIN UNIT TO THE DESIRED LEVEL.
- REMEMBER TO SWITCH OFF THE POWER OF THE MUSIC SYSTEM (MAIN UNIT)
WHEN YOU ARE FINISHED USING THE EXTERNAL DEVICE.

1 Year Guarantee from Shine-Mart Ltd, Trademark owners of Duronic Products.
NOTE: THESE STATEMENTS DO NOT AFFECT YOUR STATUTORY RIGHTS AS A CONSUMER
This product has been manufactured under the strictest or quality control procedures, and using
the highest quality of materials, to ensure excellent performance and reliability. It will give very
good and long lasting service, provided it is properly used and maintained.
The product is guaranteed for 1 years from the date of original purchase. If any defect arises due
to a faulty materials or poor workmanship, the faulty product must be returned to the original place
of purchase. Refund or replacement is at the discretion of that company.
Duronic Products are offered with a 1 year guarantee under the following conditions:
1. The product must be returned to the retailer with original proof of purchase.
2. The product must be installed and used in accordance with the instructions contained in
this operating manual.
3. It must be used only for domestic purposes.
4. It does not cover wear and tear, malicious damage, misuse, neglect, inexpert repairs or
consumable parts.
5. Shine-Mart Ltd has no responsibilities for accidental or consequential loss or damage.
6. Shine-Mart Ltd are not liable to carry out any type of servicing work, under the guarantee
7. Valid in the UK only
This product is fitted with BS:1363 plug and 3AMP fuse
Imported by Shine-Mart Ltd, RM3 8SB
Information on waste Disposal for Consumers of Electrical & Electronic Equipment.
This mark on a product and/or accompanying documents indicates that when it is to be disposed of,
it must be treated as Waste Electrical & Electronic Equipment, (WEEE).
Any WEEE marked products must not be mixed with general household waste, but kept separate for the
treatment, recovery and recycling of the materials used.
For proper treatment, recovery and recycling; please take all WEEE marked waste to your Local Authority
Civic waste site, where it will be accepted free of charge.
If customers dispose of Waste Electrical & Electronic Equipment correctly, they will be helping to save
valuable resources and preventing any potential negative effects upon human health and the environment,
of any hazardous materials that the waste may contain.
E-11