DVIGear DVI-5314c User manual

User Guide
DVI + Audio 1x4 Splitter / Repeater
DVI-5314c

TABLE OF CONTENTS
SECTION PAGE
PRODUCT SAFETY ....................................1
PRODUCT LIABILITY...................................1
1.0 INTRODUCTION ...................................2
2.0 SPECIFICATIONS ..................................3
3.0 PACKAGE CONTENTS ..............................4
4.0 CONNECTING THE HARDWARE......................4
5.0 OPERATING THE UNIT..............................5
6.0 TROUBLESHOOTING ...............................8
7.0 LIMITED WARRANTY ...............................9
8.0 REGULATORY COMPLIANCE ........................9

WARNING – Product Safety
1. Do not dismantle the product housing or modify the printed circuit board
module as this may result in electrical shock or burn.
2. Do not attempt to service this product yourself as opening or removing the
product housing may expose you to dangerous voltages or other hazards.
Refer all servicing to qualied service personnel.
3. Keep this product away from liquids. Spills into the product housing may
result in re, electrical shock, or equipment damage. If liquid spills into the
housing, unplug the product immediately. Have the product checked by a
qualied service engineer before using it again.
4. Place the product in an even and stable location. If the product falls or is
dropped, it may cause an injury and/or malfunction.
5. Avoid exposing the product to extreme temperatures or to high humidity
levels as this may result in damage to the product.
6. Only use the supplied External AC Power Adapter. The use of other power
adapters may cause this product to fail or may cause a re.
7. Do not twist or exert excessive force on the ends of the connected cables as
this can cause them to malfunction. Take care to ensure that all connected
cables are not forced to bend more than their minimum bend radius.
Product Liability
Every effort has been made to ensure that this product is free of defects.
DVIGear cannot be held liable for the use of this product or for any direct or
indirect consequential damages arising from its use. It is the responsibility of
the users of this product to check that it is suitable for their requirements and
that it is installed correctly.
All rights are reserved. No parts of this manual may be reproduced or transmitted
by any form or means, electronic or mechanical, including photocopying,
recording or by any information storage or retrieval system, without the written
consent of DVIGear.
DVIGear reserves the right to revise any of its hardware and software, following
its policy to modify and/or improve its products where necessary or desirable.
This statement does not affect the legal rights of the user in any way. All
third-party trademarks and copyrights are recognized. The DVIGear logo is a
registered trademark of DVIGear, Inc. HDMI™ is a registered trademark of
HDMI LLC. All other trademarks are the property of their respective holders.
-1-

-2-
1.0 INTRODUCTION
The DVI-5314c is a high performance digital repeater with one (1) DVI input and
four (4) independent, re-clocked DVI outputs. All inputs and outputs are HDMI v1.3
compatible, enabling full interoperability with both DVI and HDMI sources and
displays. This unit accepts a single DVI or HDMI input signal, which is de-serialized,
buffered and then applied to independent DVI / HDMI compatible transmitters at
each output. This re-clocking process ensures a substantial reduction in jitter,
which results in crisp, stable images. The DVI-5314c also includes a 1x4 audio
distribution amplier for both analog stereo audio and S/PDIF digital audio signals.
This unit supports a full array of DVI and HDMI v1.3 features, making it a perfect
solution for high quality digital signal distribution in professional systems.
Our professional digital distribution products have been serving the industry for
over ten (10) years. DVIGear offers a full line of high quality Digital Matrix Routers,
Switchers, Splitters, Video Scalers, Up/Down/Cross Converters, Format
Converters and Analog-Digital Converters, as well as a wide range of long-reach
Digital Cables, Extenders, and Optical Transmission systems.
1.1 Features
This product offers several advanced features:
• HDMIv1.3,DVIv1.0,andHDCPcompliant
• Supports8-bitcolor,10-bitand12-bitDeepColormodes
• SupportsPCresolutionsupto1600x1200and1920x1200pixels
• SupportsHDTVresolutionsupto1080pand2048x1080
• Built-in1x4distributionampliersforanalogstereoaudioandS/PDIF
digital audio
• SupportsDolbyDigital,DolbyDigitalPlus,DolbyTrueHD,andDTS-HD
Master Audio (only with HDMI v1.3 input signal)
• SupportsHDMIsignalsusingoptionalDVI-to-HDMIcables
• InputSignalEqualizationenableslongercableruns
• Independentre-clockedoutputsprovidemaximumjitterreductionand
superior image stability
• Automaticdiscoveryofconnecteddisplay’sEDIDorselectionof
internally stored EDID values
• Ruggedmetalenclosure-mayberackmountedusingoptionalDVI-5300-RMkit
• ACpoweradapterwithlockingplugforaddedsecurity

-3-
2.0 SPECIFICATIONS
Model Number
DVI-5314c DVI + Audio 1x4 Splitter / Repeater
General Specications
Compliance DVI v1.0, HDMI v1.3 and HDCP
Maximum Pixel Clock Frequency 225 MHz
Maximum Video Bit Rate 2.25 Gbps (single-link)
Color Depth 8-bit, 10-bit, or 12-bit
PC Resolutions Up to 1920x1200 and 1600x1200
HDTV Formats 480i, 480p, 576i, 576p, 720p, 1080i, 1080p, and 2048x1080
Digital Audio Support Dolby Digital, Dolby Digital Plus, Dolby TrueHD and DTS-HD Master
Audio (only with HDMI v1.3 input signal)
Audio Bandwidth 20 Hz to 20 kHz
Audio Impedance Analog Stereo: 20KΩ S/PDIF: 75Ω
Audio Levels Analog Stereo: Unity, Nominal S/PDIF: 0.5-1V p-p
Input Signal Equalization +10 dB correction @ 825 MHz
Maximum Input Cable Length 12.5 meters using DVIGear SHR™ Series copper cables
Maximum Output Cable Length 10 meters using DVIGear SHR™ Series cables, longer if using DVIGear (ACE™)
Input /Output Connectors
DVI Input 1x 29-pin female DVI connector
DVI Outputs 4x 29-pin female DVI connectors
Analog Stereo Input 1x 3.5mm PC audio female connector
Analog Stereo Outputs 4x 3.5mm PC audio female connectors
S/PDIF Input 1x RCA female connector
S/PDIF Outputs 4x RCA female connectors
Mechanical
Dimensions (H-W-D) 1.8” x 8.6” x 5.6” (46.6 mm x 218.2 mm x 142.8 mm)
Net Weight 2.3 lbs. (1054 g)
Environmental Specications
Operating Temperature +32° to +122°F (0° to +50°C)
Storage Temperature +14° to +158°F (-10° to +70°C)
Humidity (storage / operating) 10% to 90% (non-condensing)
Warranty
Limited Warranty 3YearsParts and Labor
Power Requirements
External AC Power Adapter Input: 100-240 VAC, 50-60Hz Output: 5VDC, 2.6A
Regulatory Approvals
Splitter / Repeater Unit FCC, CE, RoHS
External AC Power Adapter FCC, CE, UL, CUL, PSE, GS, RoHS
Included Accessories
1x External AC Power Adapter with USA plug, 1x User Guide
Optional Accessories
DVI-5300-RM Rack Mount Kit for DVI-5300 Series Splitters - accepts two units
DVI-7206-PS International AC Power Adapter (USA, Euro, UK, or Australian plug)

-4-
3.0 PACKAGE CONTENTS
Beforeattemptingtousethisunit,pleasecheckthepackagingandmakecertain
the following items are contained in the shipping carton:
• 1xDVI-5314cDVI+Audio1x4Splitter/Repeater
• 1xExternalACPowerAdapter
• 1xUserGuide
Note: Please retain the original packing material should the need ever arise to return the unit.
If you nd any items are missing, contact your reseller or DVIGear immediately. Please have
the Model Number, Serial Number, and Invoice Number available for reference when you call.
4.0 CONNECTING THE HARDWARE
Please study the images below to become familiar with the location of the
controls, status LEDs, signal input, signal outputs, and the power input.
DVI-5314cDVI+Audio1x4Splitter/Repeater
TheDVI-5314chasasingleDVI-Dinputanda+5VDCpowerinputjack.Theunit
has an analog stereo audio input, S/PDIF digital audio input, and corresponding
audio outputs. All of these connections, as well as the DVI-D output connectors,
are located on the rear panel.
4.1 Input / Output Connections
Connect a DVI-D or HDMI compliant input signal from a suitable source device
to the DVI Input Port. Next connect the output devices (typically displays) to the
DVI Output Ports. Make certain that all cables are securely plugged in on both
ends. To ensure the best results, always use high quality cables. Do not exceed
the recommended cable lengths indicated on Page 3 of this User Guide.

-5-
4.2 Connecting the Power
This product is shipped with an External AC Power Adapter that converts 100-240
VACat50/60Hzto+5VDCwith2.6Aoutputcurrent.Connecttheoutputcable
from the AC Power Adapter to the locking receptacle on the rear panel. Take care
to insert and then twist the connector a quarter turn in the clockwise direction.
There is no power switch on these units. The units will turn ON as soon as the
supplied AC Power Adapter is connected to a live AC power outlet.
4.3 Connecting the Audio Inputs and Outputs
If the source device has a digital audio (S/PDIF) output, connect it to the unit’s
S/PDIF input, and then connect unit’s S/PDIF outputs to the desired destination
devices. If the destination devices can accept only analog stereo audio, then
connect appropriate analog audio source and destination devices using the
provided 3.5mm input / output connectors.
5.0 OPERATING THE UNIT
To use the DVI-5314c splitter, rst connect a DVI-D or a DVI-HDMI cable
from the DVI or HDMI source device to the input of the splitter. Next, connect
the outputs of the splitter to their destination devices (typically displays or
projectors). Take care to ensure the cable quality and lengths are consistent with
the recommendations provided herein. Once this is complete, connect the audio
inputs and outputs to their respective source and destination devices.
Once the input and output cables and External AC Power Adapter are connected,
plug the power adapter into a live AC power receptacle and the splitter will begin
to function. A Power LED on the front of the unit will conrm power is present.
Other than connecting cables and applying power, there are no other set-up steps
required, with the exception of setting the EDID selector switch on the front panel.
Note: Proper operation of this product depends on the use of high quality cables.
DVIGear’s Super High Resolution (SHR™) DVI or HDMI cables provide low loss, low jitter,
high bandwidth signal handling, and are the recommended cables for use with this product.
5.1 EDID Management
EDID (Extended Display Identication Data) is a collection of data cached inside
all modern displays that describes the unit’s capabilities. The EDID information
is dened by a standard published by the VESA (Video Electronics Standards
Association) and includes information such as the manufacture name, model
number, supported resolutions and video timings, supported audio formats, color
space, etc. During boot-up, a source device must be able to read the EDID of the
connected display. When using a splitter, it is necessary that the EDID from one
of the connected displays be passed back to the source device. The EDID value
used is critical to the performance of the system as a whole.

-6-
On the front of the unit there is an EDID selection switch. This switch controls
what EDID information the splitter will report to the source device. The EDID
information provided to the source can either be EDID from one of the connected
displays (AUTO EDID Mode) or from an on-board memory chip that contains a
library of the most commonly used resolutions (INT EDID Mode). These internally
stored resolutions are listed in the table below.
Resolution Vertical Rate
(Hz) Scan Format
480p 720x480 60 Progressive
576p 720x576 50 Progressive
720p 1280x720 50,60 Progressive
1080i 1920x1080 50,60 Interlaced
1080p 1920x1080 50,60 Progressive
VGA 640x480 60 Progressive
SVGA 800x600 60 Progressive
XGA 1024x768 60 Progressive
SXGA 1280x1024 60 Progressive
UXGA 1600x1200 60 Progressive
WXGA 1280x800 60 Progressive
WXGA+ 1440x900 60 Progressive
WSXGA+ 1680x1050 60 Progressive
WUXGA 1920x1200 60 Progressive
When set to the AUTO position, the splitter will automatically discover and apply
the EDID based on a predetermined selection hierarchy as follows:
HDMI v1.3 HDMI v1.2 DVI
When the splitter powers ON, it automatically begins the EDID discovery process
by sequentially scanning the connected displays on all outputs, starting with
Output #1, then Output #2, etc. The splitter will select the EDID from the rst
HDMI v1.3 compatible display that it nds. If no such displays are connected
to the splitter, it will select the rst EDID that it nds from a connected display
that is HDMI v1.2 compatible. If no such displays are found, it will select the rst
EDID that it nds from a connected DVI display. The selected EDID information
becomes the “reference EDID” and is stored in the splitter’s memory. When the
connected source device boots up, it will read the EDID stored in the splitter’s
memory and react as if it were connected directly to the display that provided it.
For example, if the display connected to Output #1 is a DVI monitor, or if no
display is connected, the splitter will search for EDID information from Output
#2, then Output #3, and Output #4, until it nds a display with valid HDMI EDID

-7-
information. In the event none of the outputs has an HDMI display connected, the
splitter will use the EDID of the rst DVI display that is connected as the “reference
EDID” for the source device.
The default factory setting for the EDID switch setting is AUTO. This setting
works best for most applications. If one or more displays do not operate properly
such that there is no image, or the image is too large or too small, then reset the
EDID switch to the INT position. After changing the EDID switch setting, it is
necessary to cycle the power to the splitter (turn OFF, then turn ON) in order to
force the source and the displays to re-sync the EDID information. With some
source devices (PCs) it may be necessary to re-boot in order to recognize the new
EDID information.
5.2 LED Operation
There are two types of status LEDs that indicate the operation of the splitter:
Input LEDs and Output LEDs.
INPUT LEDs: Power, HDMI/DVI, HDCP, and SYNC
Power: LED illuminates red when the External AC Power Supply is
connected to both the unit and a live AC power outlet.
HDMI/DVI: LED illuminates green when the source is HDMI. The LED is
turned off if the source is DVI.
HDCP: (High-bandwidth Digital Content Protection) LED is
illuminated green if the input signal is HDCP encrypted.
SYNC: LED illuminates green if the source provides an active signal.
OUTPUT LEDs: These are identied with a number from 1 to 4. The numbers
correspond to the splitter’s outputs. These LEDs will be illuminated green if the
output of the splitter is connected to a working display or other type of output
device.

-8-
6.0 TROUBLESHOOTING
In the event of problems, rst make certain that the input and output cables are
connected securely and are of the highest quality possible.
Note: Use of low quality cables can seriously degrade the performance of this product. To
ensure optimal performance and maximum cable distance, use premium quality cables such
as DVIGear’s Super High Resolution (SHR™) Series or equivalent.
Next, check the Power LED to make certain that the splitter is receiving power. It
should be fully illuminated and not ickering or going on and off intermittently. An
intermittent Power LED may indicate a problem with the AC Power Adapter or that
the voltage applied to the AC Power Adapter input is too low.
If the input signal is HDCP encrypted, check to ensure that the connected
display(s) or other output device(s) are HDCP compatible. Also check to ensure
that the source device supports HDCP Repeater functionality.
Note: For troubleshooting HDCP links, it can be very helpful to have a test generator that
can turn HDCP On and Off manually. DVIGear’s DVI-7050a HDMI Test Generator is a good
solution for this requirement.
Some Blu-ray players and DVD players will provide non-HDCP encrypted content briey
on power-up (e.g. splash screen). Also many DVDs and Blu-ray players intentionally do not
use HDCP encryption on the previews that precede the main feature; this can provide a
helpful indication when diagnosing HDCP related problems.
Should the problem persist after trying the above suggestions, please contact
your dealer for additional assistance. Should the dealer’s technical personnel be
unable to assist you, please contact DVIGear via telephone at 1.888.463.9927
(toll-free for United States and Canada) or 1.770.421.6699. You may contact
DVIGear by e-mail at [e-mail].

-9-
7.0 LIMITED WARRANTY
LIMITED WARRANTY – With the exceptions noted in the next paragraph,
DVIGear, Inc. warrants to the original purchaser that the equipment it
manufactures or sells will be free from defects in materials and workmanship for
a period of three (3) yearsfrom the date of purchase. Should this product,
in DVIGear’s opinion, prove defective within this warranty period, DVIGear, at
its option, will repair or replace this product without charge. Any defective
parts replaced become the property of DVIGear. This warranty does not apply
to those products which have been damaged due to accident, unauthorized
alterations, improper repair, modications, inadequate maintenance and care, or
use in any manner for which the product was not originally intended.
If repairs are necessary under this warranty policy, the original purchaser must
obtain a Return Authorization Number from DVIGear and return the product,
freight prepaid, to a location designated by DVIGear. After repairs are complete,
the product will be returned, freight prepaid.
LIMITATIONS - All products are sold “as is” and the above Limited Warranty is in lieu
of all other warranties for this product, expressed or implied, and is limited to three
yearsfrom the date of purchase. DVIGear assumes no liability to distributors,
resellers, end users, or any third parties for any loss of use, revenue, or profit.
DVIGear makes no other representation of warranty as to tness for the purpose
of merchantability or otherwise in respect to any of the products sold. The
liability of DVIGear with respect to any defective products will be limited to the
repair or replacement of such products. In no event shall DVIGear be responsible
or liable for any damage arising from the use of such defective products, whether
such damages are direct, indirect, consequential or otherwise, and whether such
damages are incurred by the reseller, end user, or any third party.
8.0 REGULATORY COMPLIANCE
This product has been tested for compliance with appropriate FCC and CE
rules and regulations. The supplied AC Power Adapter has been tested for
compliance with FCC, CE, UL, CUL, PSE and GS rules and regulations. This
product and the supplied AC Power adapter are RoHS compliant.

www.dvigear.com
Your Digital Connectivity Experts
Toll Free 888.463.9927
Phone [phone]
Fax [phone]
DVIGear, Inc.
1059 Triad Court, Suite 8
Marietta, Georgia 30062-2258
DVI-5314c-UG-01 / March.2013