DW Windsor Sabre 1 User manual

Sheet 1 of 3
Tools not supplied.
The information shown below details the recommended bolt torque when
mounting Sabre to post top bracket.
Fig. 1
Fig. 4
*Maximum weight of lantern including mounting bracket.
Fig. 1 - Sabre 2 (32 LED)
Fig. 2 Stirrup wall mounting option
Fig. 3 Post top mounting option
Due to continuous product development the details within this document
are subject to change at any time, please contact us for the most up-to-date
information or visit: www.dwwindsor.com
3d50302-08 - Issue 1
DW Windsor
Pindar Road, Hoddesdon, Hertfordshire, EN11 ODX
T: [phone] | E: [e-mail]
dwwindsor.com
The Sabre Range
LED Flood Light
Sabre 1, 2 and 3
Installation Instructions
IMPORTANT
Product Details
Mounting options
Tools Required
Recommended Torque
10mm Allen Key2 Pozi or Slotted
Screwdriver
35mm Allen Key1
Dimensions (mm) Max. Weight (kg)* Windage m²
A B C
Sabre 1 283 390 73 3.8 0.016
Sabre 2 386 488 81 7.8 0.029
Sabre 3 460 595 94 13.1 0.045
Power Ranges (Watts)
Standard CLO Enabled
Sabre 1 12 - 55 10 - 46
Sabre 2 - 24 LED 17 - 79 14 - 67
Sabre 2 - 32 LED 22 - 105 18 - 88
Sabre 3 41 - 198 35 - 151
Post Top Bracket Mounting Torque (Nm)
Sabre 1 10
Sabre 2 10
Sabre 3 10
Entry Options Fig.
Stirrup wall mount 2
Post top 3
230VAC 50Hz
IP66 IK08
• DISCONNECT ELECTRICAL SUPPLY BEFORE INSTALLATION OR SERVICING.
• THIS PRODUCT MUST BE EARTHED.
• THIS PRODUCT IS DESIGNED TO OPERATE OUTDOORS. IF REQUIRED TO BE
USED INDOORS PLEASE CONSULT DW WINDSOR.
• THIS PRODUCT IS FITTED WITH HIGH IMPACT RESISTANT GLASS AND MAY
BE MOUNTED AT HEIGHTS ABOVE OR BELOW 5m.

Sheet 2 of 3
Step 1
Turn off mains power. Loosen and remove M10 Allen bolts and remove the
stirrup bracket from the main body.
Step 3
Reattach main floodlight body to the newly mounted stirrup. Adjust to the
desired angle then fully tighten M10 Allen bolts to fix in place. Unscrew M5 Allen
bolts on the top of the light to open the gear compartment lid.
Step 5
Tighten cable gland around power cable. Close the gear compartment and
re-tighten the M5 bolts ensuring they are fully tightened to maintain water
ingress rating.
Step 2
Position the stirrup bracket on the wall, use the existing holes in the stirrup
bracket as guides, drill holes and insert anchors. Tighten screws into anchor
points to fix stirrup securely to wall.
Step 4
Loosen cable gland and feed power cable through into the gear compartment.
Insert the live, neutral and ground wires in their respective ports on the terminal
block, tighten terminal block screws fully.
Step 6
Once cable routing has been completed and checked mains power can be
restored. For products with CMS expect a slight delay on initial power up.
LEDs contained within this luminaire shall only be replaced
by the manufacturer, their service agent or similar qualified
person.
3d50302-08 - Issue 1
DW Windsor
Pindar Road, Hoddesdon, Hertfordshire, EN11 ODX
T: [phone] | E: [e-mail]
dwwindsor.com
The Sabre Range
LED Flood Light
Sabre 1, 2 and 3
NOTE!
Sabre Installation Steps | Stirrup Wall Mounting

Sheet 3 of 3
Step 1
Turn off mains power. Loosen and remove M10 Allen bolts and remove the
stirrup bracket from the main body.
Step 3
Reattach main floodlight body to the newly mounted stirrup. Adjust to the
desired angle then fully tighten M10 Allen bolts to fix in place. Unscrew M5 Allen
bolts on the top of the light to open the gear compartment lid.
Step 5
Tighten cable gland around power cable. Close the gear compartment and
re-tighten the M5 bolts ensuring they are fully tightened to maintain water
ingress rating.
Step 2
Position the stirrup bracket on the post top bracket, tighten the provided bolts
to 10Nm to fix them.
Step 4
Loosen cable gland and feed power cable through into the gear compartment.
Insert the live, neutral and ground wires in their respective ports on the terminal
block, tighten terminal block screws fully.
Step 6
Once cable routing has been completed and checked mains power can be
restored. For products with CMS expect a slight delay on initial power up.
LEDs contained within this luminaire shall only be replaced
by the manufacturer, their service agent or similar qualified
person.
3d50302-08 - Issue 1
DW Windsor
Pindar Road, Hoddesdon, Hertfordshire, EN11 ODX
T: [phone] | E: [e-mail]
dwwindsor.com
The Sabre Range
LED Flood Light
Sabre 1, 2 and 3
NOTE!
Sabre Installation Steps | Stirrup Wall Mounting