DW Windsor Kirium Pro Series User manual

Sheet 1 of 4
• 2x M10 Screw
• 4x Disc Spring Washer
• 2x M10 Grub Screw
• 2x Locking Nut (for Kirium Pro 2 and 3 only, when using a Side Entry)
Tools not supplied.
The Kirium Pro range is supplied with entry detached from the luminaire.
The information shown below details the length of column engagement for
each entry option.
Fig. 1
Fig. 3
Fig. 2
*Maximum weight of lantern including post top entry.
Fig. 1 - Kirium Pro 2 (Please See Kirium Pro data sheet for all Kirium Pro technical drawings).
Fig. 3 - Kirium Pro 2 (Please See Kirium Pro data sheet for all Kirium Pro technical drawings).
Fig. 2 - Length of column engagement for each entry option.
• Luminaire to be positioned so that prolonged staring into the
luminaire at distances closer than shown below is not expected.
o Kirium Pro1 - 3.4m
o Kirium Pro2 - 4.8m
o Kirium Pro3 - 6.6m
• Do not stare at operating light source.
• Personnel to wear Protective Safety Glasses compliant with EN166 1F/ EN169 -
5 when commissioning or maintaining this luminaire.
•
Due to continuous product development the details within this document
are subject to change at any time, please contact us for the most up-to-date
information or visit: www.dwwindsor.com
50264-004 - 10/630/01
DW Windsor
Pindar Road, Hoddesdon, Hertfordshire, EN11 ODX
T: [phone] | E: [e-mail]
dwwindsor.com
Kirium® Pro is a registered design.
The Kirium Pro Range
LED Road Light
Kirium Pro 1, 2 and 3
Installation Instructions
IMPORTANT
NOTE!
Product Details
Column Engagement Fasteners Supplied
Tools Required
Recommended Torque
76mm Post Top 42mm Side Entry
60mm Post Top and Side Entry
5mm Allen Key2 Pozi or Slotted
Screwdriver
3
8mm Allen Key1
Dimensions (mm) Max. Weight (kg)* Windage m²
A B C
Kirium Pro 1 610 140 350 8.5 0.048
Kirium Pro 2 720 140 350 9.8 0.052
Kirium Pro 3 1010 167 415 17.1 00.867
Power Ranges (Watts)
Standard CLO Enabled
Kirium Pro 1 7-105 6-95
Kirium Pro 2 22-198 20-177
Kirium Pro 3 41-394 37-353
Entry Mounting Torque (Nm) Column Mounting Torque (Nm)
Kirium Pro 1 30 16
Kirium Pro 2 30 16
Kirium Pro 3 30 16
Entry Options Column Engagement
76mm Post Top Entry 80mm
42mm Side Entry 110mm
60mm Post Top and Side Entry 100mm
230VAC 50Hz
IP66 IK08
• DISCONNECT ELECTRICAL SUPPLY BEFORE INSTALLATION OR SERVICING.
• THIS PRODUCT MUST BE EARTHED.
• THIS PRODUCT IS DESIGNED TO OPERATE OUTDOORS. IF REQUIRED TO BE
USED INDOORS PLEASE CONSULT DW WINDSOR.
• THIS PRODUCT IS FITTED WITH HIGH IMPACT RESISTANT GLASS AND MAY
BE MOUNTED AT HEIGHTS ABOVE OR BELOW 5m.

Sheet 2 of 4
Step 1
Loosen and remove pre-attached 2x M10 screws and 4x disc spring washers
from luminaire with 8mm allen key.
Step 3
Undo quick-release side latches, and leave latches in open position.
Step 5
Loosen cable gland cap within base and feed through cable tail.
Step 2 (See Step 2A for Side Entry installation instructions)
Fit entry to luminaire with supplied fasteners, tightening to 30Nm torque. 4x
Disc spring washers must be installed in the correct orientation.
Step 4
Pivot lift-off head 45° away from base and remove. Store lift-off head in safe
area during base installation.
Step 6
Wire cable to electrical disconnect with Pozi or Slotted Screwdriver. Tighten
gland cap to 6Nm torque to ensure IP sealing is maintained.
Ensure entry is aligned to desired mounting angle.
Undo safety wire before removal of lift-off head. Ensure lift-off head is
fully constrained at all times during removal. Kirium Pro 3 Only.
50264-004 - 10/630/01
DW Windsor
Pindar Road, Hoddesdon, Hertfordshire, EN11 ODX
T: [phone] | E: [e-mail]
dwwindsor.com
The Kirium Pro Range
LED Road Light
Kirium Pro 1, 2 and 3
NOTE!
• LEDs contained within this luminaire shall only be replaced by the
manufacturer, their service agent or similar qualified person.
•The Live Supply is insulated (single) from the DALI conductor.
Kirium Pro Installation Steps | Post Top Entry

Sheet 3 of 4
Step 2A
Fit entry to luminaire with supplied fasteners, tightening to 30Nm torque. 4x
Disc spring washers must be installed in the correct orientation.
Ensure entry is aligned to desired mounting angle.
Step 7 (See Step 7A for Side Entry installation instructions)
Loosen 2x M10 grub screws on entry with 5mm allen key. Slide entry on to
column (See column engagement table). Tighten grubs screws to 16Nm.
Step 7A
Loosen 2x M10 grub screws on entry with 5mm allen key. Slide entry on to
column (See column engagement table). Tighten grubs screws to 16Nm.
Step 9 (See Step 9A for Side Entry installation instructions)
Close luminaire and fasten quick-release side latches.
Step 8
Angle lift-off head 45° and fit to base ensuring both pivot points are fully
engaged.
CRITICAL! Attach safety wire to lift-off head before closing luminaire.
Kirium Pro 3 Only.
Align luminaire with area to be illuminated.
Align luminaire with area to be illuminated.
LEDs contained within this luminaire shall only be replaced
by the manufacturer, their service agent or similar qualified
person.
50264-004 - 10/630/01
DW Windsor
Pindar Road, Hoddesdon, Hertfordshire, EN11 ODX
T: [phone] | E: [e-mail]
dwwindsor.com
The Kirium Pro Range
LED Road Light
Kirium Pro 1, 2 and 3
NOTE!
Kirium Pro Installation Steps | Post Top Entry
Kirium Pro Installation Steps | Side Entry

Sheet 4 of 4
Anti-Glare Shields can be fitted to the luminaire post-installation, without
opening the product.
Spring Clips and M4 screws are supplied in the following quantities for each
anti-glare shield option.
• 2x for Front Shields
• 2x for Back Shields
• 4x for Front & Back Shields (6x for Front & Back Shields on Kirium Pro 3)
Step 9A
Close luminaire and fasten quick-release side latches.
Spring Clips
Fit spring clips to luminaire before attaching anti-glare shields. Spring clips are
push-fit and non-removeable once fitted.
Tools not supplied.
Fig. 5 - Kirium Pro front anti-glare shield installation.
Fig. 7 - Kirium Pro full anti-glare shield installation.
Ensure Anti-Glare Shield Clips are securely attached to the luminaire.
Fig. 6 - Kirium Pro back anti-glare shield installation.
50264-004 - 10/630/01
Fig. 4
Fig. 5
Fig. 7Fig. 6
Fig. 4 - Tools required for Kirium Pro Anti-Glare Shield installation. Not supplied.
The Kirium Pro Range
LED Road Light
Kirium Pro 1, 2 and 3
Kirium Pro Installation Steps | Side Entry
Anti-Glare Shield
Fasteners Supplied
Tools Required
2.5mm Allen Key4