Dwyer Instruments MM10 Series User manual

OPERATING INSTRUCTIONS
SERIES MM10 DIGITAL MULTIMETER
SAFETY INFORMATION
The following safety information must be observed to insure
maximum personal safety during the operation of this meter.
Do not use the meter if the meter or test leads look damaged, or
if you suspect that the meter is not operating properly.
Never ground yourself when taking electrical measurements. Do
not touch exposed metal pipes, outlets, fixtures, etc., which might
be a ground potential. Keep your body isolated from ground by
using dry clothing, rubber shoes, rubber mats, or any approved
insulating material.
Turn off power to the circuit under test before cutting,
unsoldering, or breaking the circuit. Small amounts of current
can be dangerous.
Use caution when working above DC 60V or AC 30Vrms. Such
voltages pose a shock hazard.
When using the probes, keep your fingers behind the finger
guards on the probes.
Measuring voltage which exceeds the limits of the multimeter
may damage the meter and expose the operator to a shock
hazard. Always recognize the meter voltage limits as stated on
the front of the meter.
GENERAL SPECIFICATIONS
Display: 3-1/2 digit liquid crystal display (LCD) with a maximum
reading of 1999.
Polarity: Automatic, positive implied, and (-) for negative polarity
indication.
Overload: (1) or (-1) is displayed on LCD.
Low Battery Indication: When " " shows on LCD, battery
needs to be replaced.
Sampling Rate: 2.5 times per second.
Operating Environment: 0°C~40°C 80% RH.
Storage Temperature: -10°C~60°C 0~80% RH with battery
removed from meter.
Power: One 006P 9V standard battery.
Battery Life: 150 hours approx.
Dimension: 125 mm (H) x 68 mm (W) x 25 mm (D).
Weight: 150g approx. including battery.
Accessory: Instruction manual, test leads, (1) 9V battery.
SPECIFICATIONS
DCV
Range Resolution Accuracy Input
Impedance
Overload
Protection
2V 1mV 0.5% + 1 dgt
20V 10mV
200V 100mV
600V 1V
1.5% + 1 dgt 10MΩ
DC 600V
AC 600V
rms
ACV
Range Resolution Accuracy Input
Impedance
Overload
Protection
200V 100mV
2% + 3 dgt
(40 Hz-
500 Hz)
600V 1V 2.5% + 3 dgt
4.5MΩ
DC 600V
AC 600V
rms
DCA
Range Resolution Accuracy Input
Impedance
Overload
Protection
2mA 1μA
20mA 10μA
200mA 100μA
1.5% + 1 dgt 0.3V 0.5A Fuse
& Diodes
10A 10mA 2% + 1 dgt 0.7V
Resistance (Ω)
Range Resolution Accuracy Open
Voltage
Overload
Protection
200Ω0.1Ω2% + 2 dgt
2KΩ1Ω2.8V
20KΩ10Ω
200KΩ100Ω
2MΩ1KΩ
1.5% + 2 dgt
20MΩ10KΩ2.5% + 2 dgt
0.3V
DC/AC
500V
rms
Diode Test
Range Resolution Test
Current
Open
Voltage
Overload
Protection
1mV 1mA ≈2.8V DC/AC
500V rms
Continuity Test x
Range Resolution Sound Open
Voltage
Overload
Protection
x0.1Ω<30Ω<≈2.8V AC/DC
500V rms
Transistor hFE
Range Measuring
Scope
Test
Voltage
Test
Current
Overload
Protection
NPN
PNP 0-1000 <3.2V IB≈10μA
LED
Range Measuring
Scope
Test
Voltage
Test
Current
Overload
Protection
LED 1.5-3V 3V ≈25mA

OPERATION
DCV (ACV) Measurement
1. Plug red test lead to "VΩmA" jack, and black test lead to
"COM" jack.
2. Turn the function/range selector to "DCV" or "ACV" region.
(If measuring an unknown voltage, start from the highest
range then adjust to a proper lower range for the best
resolution.)
3. Connect the other ends of the test leads to the desired
circuit.
4. Get the reading from the LCD.
DCA Measurement
1. Plug red test lead to "VΩmA" jack (if measuring a current
between 200mA and 10A, plug to "10A" jack instead), and
black test lead to "COM" jack.
2. Turn the function/range selector to "DCA" region. (If
measuring an unknown current, start from the highest range
then adjust to a proper lower range for the best resolution.)
3. Connect the other ends of the test leads in series with the
desired circuit.
4. Get the reading from the LCD.
Resistance Measurement
1. Plug red test lead to "VΩmA" jack, and black test lead to
"COM" jack.
2. Turn the function/range selector to "Ω" region (if measuring
an unknown resistance, start from the highest range, then
adjust to a proper lower range for the best resolution).
3. Connect the other ends of the test leads to the desired
resistor.
4. Get the reading from the LCD.
Diode ( )Measurement
1. Plug red test lead to "VΩmA" jack, and black test lead to
"COM" jack.
2. Turn the function/range selector to " " range.
3. Connect the other end of red test lead to the positive pole
(P) of the diode, and the other end of the black test lead to
the negative pole (N).
4. Get the reading from the LCD. (If connection to poles of
diode is reverse, LCD would display "I".)
Continuity xMeasurement
1. Plug red test lead to "VΩmA" jack, and black test lead to
"COM" jack.
2. Turn the function/range selector to " x" range.
3. Connect the other ends of the test leads to the desired
resistor.
4. Get the reading from the LCD.
hFE Measurement (for Transistor)
1. Turn the function/range selector to "hFE" (NPN or PNP)
region.
2. Insert the transistor pins into "hFE" jack according to E.B.C.
sequence.
3. Get the reading from the LCD.
LED Test
1. Turn the function/range selector to "NPN/LED" range.
2. Insert the LED into the measuring jack according to the "+" "-
" position, and a normal LED will be bright.
3. This function is used only to judge a LED rated 15V~3V for
its brightness or not. The reading on LCD means nothing.
MAINTENANCE
WARNING: Remove test leads before changing battery or
fuse or performing any servicing.
Battery Replacement
Power is supplied by a 9 volt "transistor" battery (006P DC9V).
The " " shown on the LCD indicates that replacement is
needed. When replacing, remove the two screws from the back
of the meter and lift off the rear case. Remove the battery from
the case on bottom.
Fuse Replacement
If no current measurements are possible, check for a blown
overload protection fuse. Replace the fuse with the original type
0.5A/250V, fast acting type.