DX Engineering DXE-40VE-1 User manual

40 Meter
Vertical Antenna
DXE-40VE-1
DXE-40VE-1-INS Revision 13a
© DX Engineering 2012
P.O. Box 1491 ∙ Akron, OH 44309-1491 USA
Phone: [phone] ∙ Tech Support and International: [phone]
Fax: [phone] ∙ E-mail: [email protected]

- 1 -
Table of Contents
Introduction
1
Warning
2
Overhead Power Line Safety
2
Tools Required
2
Parts Included
3
Installation
3
Site Selection
3
Mounting Pipe
4
Radial System
4
Assembly
4
Vertical Base Section
5
Base Section to Mounting Pipe
6
Assembling the Vertical Sections
6
Tuning the Vertical Antenna System
10
Guying the Vertical Antenna
11
Appendix A - Optional Radial Plate
12
Appendix B –Optional Tilt Base
13
Appendix C - Optional Vertical Feedline Current Choke
14
Optional Accessory Items
15
Technical Support and Warranty
19
Introduction
The DX Engineering DXE-40VE-1 is a fast taper 33 feet high 40 meter monoband vertical antenna
system. The vertical antenna operates over the entire 40 meter band with a SWR less than 1.5:1.
There are no traps, coils or linear loading elements to rob power. Designed with 6063 corrosion-
resistant aluminum tubing and stainless steel hardware, this antenna is very durable and attractive.
The antenna may be used as a monoband antenna on a higher frequency by simply telescoping the
tubing inward to one quarter wavelength on the desired band. As supplied, an extra element section
is part of the design to allow extension to 36 feet if necessary.

- 2 -
The DXE-40VE-1 vertical antenna system includes the antenna elements, stainless steel clamps,
mounting plate assembly, and stainless steel hardware.
Full band coverage on 40 meters with SWR under 1.5:1 - No Tuner needed
36 ft overall height
Fast Taper from rugged base to sleek top for low wind resistance
No Coils or Traps –Maximum Radiation Efficiency
Power Handling up to 5 kW - built to last
Perfect for Four Square or Phased Array systems
Easily shortened for resonance on higher bands
WARNING!
INSTALLATION OF ANY ANTENNA NEAR POWER LINES IS DANGEROUS
Warning:Do not locate the antenna near overhead power lines or other electric light or power
circuits, or where it can come into contact with such circuits. When installing the antenna, take
extreme care not to come into contact with such circuits, because they may cause serious injury or
death.
Overhead Power Line Safety
Before you begin working, check carefully for overhead power lines in the area you will be
working. Don't assume that wires are telephone or cable lines: check with your electric utility for
advice.
Although overhead power lines may appear to be insulated, often these coverings are intended only
to protect metal wires from weather conditions and may not protect you from electric shock
Keep your distance! Remember the 10-foot rule: When carrying and using ladders and other long
tools, keep them at least 10 feet away from all overhead lines - including any lines from the power
pole to your home.
Manual Updates
Every effort is made to supply the latest manual revision with each product. Occasionally a manual
will be updated between the time your DX Engineering product is shipped and when you receive it.
Please check the DX Engineering web site (www.dxengineering.com) for the latest revision manual.
Tools Required
Two 7/16 wrenches, (one of them should be open-end)
3/16 Allen wrench
Medium size standard screwdriver or 5/16 nut driver for the element clamps
3/16 and 1/4 nut drivers or wrenches
Tape measure and Felt-tip marker.
Antenna analyzer. The MFJ-259B is one suggested unit to facilitate the fine tuning of the
vertical antenna system.

- 3 -
Parts Included
Description
Quantity
Mount Plate
1
Mast Mount Channel
1
3/8 U-Bolt x 2" ID x 3.25" leg, Saddle & Hardware
2
1/4-20 x 1" Hex Head Bolt
1
1/4" Star Washer
2
DXE-CAVS-1P V-Bolt Saddle Clamp
2
DXE-ECL-040 - Element Clamp
1
DXE-ECL-060 - Element Clamp
2
DXE-ECL-10SS - Element Clamp
2
DXE-ECL-12SS - Element Clamp
1
DXE-ECL-16SS - Element Clamp
2
DXE-ECL-20SS - Element Clamp
2
DXE-ECL-24SS - Element Clamp
2
Black Vinyl Cap, for 1/2" O.D.
1
Aluminum Spacer
4
1/4-20 x 2" Hex Head Bolt, full thread
4
1/4-20 Hex Nut
6
1/4" Split Washer
4
1/4" Flat Washer
10
Antenna Element Parts
Quantity
2" (2.00") x 36" Element, Drilled (split one end)
1
1-7/8" (1.875") x 18" Element, Cut, Drilled
1
1-7/8" (1.875") x 36" Element (split one end)
1
1-3/4" (1.750") x 36" Element (split one end)
1
1-5/8" (1.625") x 36" Element (split one end)
1
1-1/2" (1.500") x 36" Element (split one end)
1
1-3/8" (1.375") x 36" Element (split one end)
1
1-1/4" (1.250") x 36" Element (split one end)
1
1-1/8" (1.125") x 36" Element (split one end)
1
1" (1.000") x 36" Element (split one end)
1
7/8" (0.875") x 36" Element (split one end)
1
3/4" (0.750") x 36" Element (split one end)
1
5/8" (0.625") x 36" Element (split one end)
1
1/2" (0.500") x 36" Element
1
Installation
Site Selection
Select a mounting location clear from power lines, structures and other antennas by a minimum of
46 feet (added 10 feet for the 10 foot safety rule). Consider overhead power lines, utility cables
and wires. The further away the vertical is mounted from local noise sources or other metallic
objects, which can re-radiate noise and affect the tuning, radiation pattern and SWR, the better. If
you are installing the optional DXE-TB-4P Tilt Base, determine the direction you want the antenna
to tilt down and make sure there is adequate clearance. There should be sufficient room for a radial
system that will extend away from the antenna equally in all directions, if possible.

- 4 -
Mounting Pipe
Use a customer supplied thick-walled galvanized steel mounting pipe at least 4 feet
long. This will allow approximately 2 feet or more to be below ground and 2 feet
above ground. A thick-walled steel pipe 1-3/4" OD is recommended with a minimum
thickness of 1/8" (1/4" preferred) should be used. The standard 1-1/4" galvanized
water pipe (with its approximate 1.7" OD) is just fine for this application and can
usually be found at your local home building supply store. When using the optional
DXE-TB-4P Tilt base a mounting pipe of up to 2" OD may be used. For permanent
mounting, use a post-hole digger to make the hole deep enough to accommodate 2
feet of pipe and a couple inches of gravel at the bottom for drainage. Set the pipe on
the gravel, use the pre-mix concrete to fill around the pipe, adding water and mixing
as you fill or mix the concrete first, then pour in the hole. Fill the hole until the concrete is level
with the ground around it. Use a level as you fill the hole to be sure the pipe is straight. Allow to set
overnight. Your location, landscape and ground conditions may require different mounting solutions
in order to have the steel mounting pipe and the vertical antenna in a secure position.
Note: Galvanized steel, rather than aluminum, is much more suitable for mounting in concrete.
Aluminum will quickly corrode due to incompatibility with the materials used to make
concrete.
.
Radial System
The use of a radial system is a key requirement for a high performance quarter wave vertical
antenna system. With a vertical antenna system, the radials are the second half of the antenna. The
radials contribute to the radiation efficiency of the entire vertical antenna system.
At a minimum, 20 radials, each 32 feet long, should be used with this antenna. Using 32 radials at
32 feet long is preferred and highly recommended. The extra radials help overcome unknown poor-
soil conditions, improve bandwidth, and ensure the best performance possible from the vertical
antenna. DXE-RADW Radial Wire, a 14 gauge stranded copper with black relaxed PVC insulation
wire is suggested for the best results.
The wire radials should placed as symmetrically as possible around the vertical antenna
and spaced evenly, regardless of how many radials are used. Do not cross or bunch any
radial wires as this detunes the radials involved. If you have limited space, put in as
many straight radials as you can. The radials must be connected to the shield of your
feedline. The DXE-RADP-3 Stainless Steel Radial Plate is an ideal optional item
which provides an excellent system for attaching radial wires to your vertical antenna
system.
Radial wires can be laid on the roots of the grass using steel or biodegradable DXE-STPL Radial
Wire Anchor Pins to hold them down. Using enough staples will ensure the wires will not be
snagged by mowers, people, or animals. Grass will quickly overgrow the radials and they will be
virtually impossible to see. An article describing this process is available the DX Engineering
website in the Tech Info section. Radials can also be buried just under the surface by using a power
edger to make a slit in the soil.
Assembly
The DXE-40VE-1 shipping box contains vertical tubing sections, insulated U-channel, 2 U-Bolt

- 5 -
assemblies, backing plate, 12 stainless steel clamps, black vinyl cap and stainless steel hardware.
Carefully un-box the antenna and separate the various parts. All of the element sections are 36"
long. Nested inside the 36" drilled base element section is the 18" drilled section for added wall
strength to the base element section. The vinyl cap for the top element section should be installed
after assembly of the vertical is complete.
Note: DXE-P8A Penetrox A Anti-Oxidant should be used between all antenna element
sections. Penetrox is an electrical joint compound to affect a substantial electrical
connection between metal parts such as telescoping aluminum tubing or other antenna
pieces. It ensures high conductivity at all voltage levels by displacing moisture and
preventing corrosion or oxidation.
UMI-81343 Never-Seez or DXE-NSBT8 Anti-Seize should be used on all clamps, bolts
and stainless steel threaded hardware to prevent galling and to ensure proper
tightening.
Vertical Base Section
The base section is made up of an insulated mounting channel, an aluminum mount plate and the
base antenna section which is 36" long, with a hole drilled at one end. Nested inside the base
antenna section is an 18" piece of tubing with a hole drilled at one end, to add wall strength to the
base section and the feed point hardware is pre-installed.
If you have chosen to use the optional DXE-TB-4P Tilt Base, refer to Appendix B. You will use a
smaller mounting plate with the DXE-TB-4P Tilt Base kit.
Using Figure 1, attach the
aluminum mount plate to the
back of the insulated channel
using four each of the 2" bolts,
eight flat washers, four spacers,
four split washers, and four nuts.
Tighten firmly, but not enough
to crush the insulated channel.
The spacers are required when
the optional Tilt Base is
installed. They are being
installed as shown on this plate
to act as a washer and for safe
keeping.
Figure 1
Locate the 36" base-section tube. Install the 18" section inside the
36" section aligning the drilled feedpoint hardware holes. Install the
feedpoint hardware (1 " hex head bolt, two star washers, two flat
washers, and two hex head nuts) as shown in Figure 2.
Figure 2

- 6 -
Install the lower element on to the insulated channel using the two 3/8" x 2" U-Bolts, two saddle
clamps, four flat washers, four split washers, and four nuts as shown in Figure 1. Use the outer
upper and lower holes of the channel. When tightening, observe the split washers. When they fully
seat (flatten out), the clamp is tight enough. Any clamp should be tightened evenly from side-to-side
with an equal amount of thread above each nut.
Base Section to Mounting Pipe
Attach the completed base section to your steel ground mounted pipe using the two DXE-CAVS-1P
Saddle Clamps, as shown in Figure 3. Use two V-Bolts, two saddles, four nuts, four flat and four
split washers. When tightening, observe the split washers. When they fully seat (flatten out), the
clamp is tight enough. Any clamp should be tightened evenly from side-to-side with an equal
amount of thread above the nut. The standard 1-1/4" galvanized water pipe (with its approximate
1.7" OD) is just fine for this application and can usually be found at your local home building
supply store.
(This view shown without
insulated channel
for clarity)
Figure 3
Assembling the Vertical Sections
Assemble the vertical elements in an area that is flat and has sufficient room for the length of the
antenna during assembly. Lay the elements out in descending diameter sizes of 1-7/8", 1-3/4", 1-
5/8", 1-1/2", 1-3/8", 1-1/4", 1-1/8", 1", 7/8", 3/4", 5/8", and 1/2" with the slits in the elements
toward the top of the antenna (the 1/2" section does not have slits). All the element sections are 36"
long.
Note: DXE-P8A -Penetrox A Anti-Oxidant should be used between all antenna element
sections. Penetrox is an electrical joint compound to affect a substantial electrical
connection between metal parts such as telescoping aluminum tubing or other
antenna pieces. It ensures high conductivity at all voltage levels by displacing
moisture and preventing corrosion or oxidation.

- 7 -
When assembling any telescoping aluminum tubing sections you should take the following steps:
1. Make sure the edges are smooth and not sharp. Deburring may be necessary, since burrs and
shavings can occur on seams as well as edges. All surfaces need to be completely smooth to
allow easy assembly of tubing sections.
Caution
Aluminum tubing edges can be very sharp.
Take precautions to ensure you do not get accidentally cut.
The raised particles and shavings that appear when the aluminum tubing is machined are
referred to as burrs, and the process by which they are removed is known as deburring.
Deburring is a finishing method used in manufacturing. Our aluminum tubing is machine cut on
both ends and machine slit on one end. Although DX Engineering manufactured aluminum
tubing is deburred, you should further assure that there are no ragged edges or protrusions.
Use the DXE-22166 Slim Grip Deburring Tool, or the DXE-22600 Deburring Tool with
Extending Handle and Extra Blades for this operation.
2. Clean the inside of the aluminum tubing to clear out any dirt or foreign material that would
cause the aluminum tubing sections to bind during assembly. Do not use any type of oil or
general lubricant between the aluminum tubing sections. Oils or general lubricants can cause
poor electrical connections for radio frequencies.
3. Clean the outside of the aluminum tubing to clear any dirt or foreign material that would cause
the clamps to malfunction during assembly.
4. The use of DXE-P8A Penetrox A is highly recommended. Penetrox A is an electrical joint
compound which effects a substantial electrical connection between metal parts such as
telescoping aluminum tubing or other antenna pieces. Using Penetrox A assures high
conductivity at all voltage levels by displacing moisture and preventing corrosion or oxidation.
5. When assembling the aluminum tubing sections, ensure the area is clear of grass, dirt or other
foreign material that could cause problems during assembly of the closely fitted telescoping
sections.

- 8 -
Using a felt tip pen, measure and mark the bottom eight element sections (1-7/8", 1-3/4", 1-5/8", 1-
1/2", 1-3/8", 1-1/4", 1-1/8", and 1") at 4". Mark the top four element sections (7/8", 3/4", 5/8", and
1/2") at 6" (the top 1/2" section does have slits but they are not used) as shown in Figure 4.
Figure 4
Slide the element clamps over each section before putting them together. Element clamp sizes are
shown in Figure 6. Align the clamps on each section facing the same direction. For final assembly,
all the clamps should be positioned approximately 1/8" from the top of each section and the body of
the clamp should be positioned between the slits as shown in Figure 5.
Figure 5
Using Figure 6 on the next page, start the assembly with the bottom 1-7/8" element section. Insert
the marked end of the 1-3/4" element section into the 1-7/8" element section until the mark is even
with the top of the 1-7/8" element section.
Position one of the larger element clamps at the very end, but not hanging over. Make sure the body
of the element clamp is positioned between the slits and tighten securely.
Repeat the procedure for the sections using the element clamps as shown in Figure 6.

- 9 -
Figure 6 - Finished
Antenna Assembly
The top section may
be adjusted to vary the
overall length from
33 to 36 feet for
fine tuning if
necessary.