dymax BlueWave LED DX-1000 User manual

Dymax BlueWave®LED DX-1000 VisiCure®
User Guide
Small-Area LED Light Source
■Instructions for Safe Use
■Setup and Operation
■Maintenance
■Ordering Spare Parts and Accessories
System Discontinued 1/1/2019

2
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
About Dymax
UV/Visible light-curable adhesives. Systems for light curing, fluid dispensing, and fluid packaging.
Dymax manufactures industrial adhesives, light-curable adhesives, epoxy resins, cyanoacrylates, and activator-cured adhesives.
We also manufacture a complete line of manual fluid dispensing systems, automatic fluid dispensing systems, and light-curing systems.
Light-curing systems include LED light sources, spot, flood, and conveyor systems designed for compatibility and high performance
with Dymax adhesives.
Dymax adhesives and light-curing systems optimize the speed of automated assembly, allow for 100% in-line inspection, and increase
throughput. System designs enable stand-alone configuration or integration into your existing assembly line.
Please note that most dispensing and curing system applications are unique. Dymax does not warrant the fitness of the product for the
intended application. Any warranty applicable to the product, its application, and use is strictly limited to that contained in the Dymax
standard Conditions of Sale. Dymax recommends that any intended application be evaluated and tested by the user to ensure that desired
performance criteria are satisfied. Dymax is willing to assist users in their performance testing and evaluation by offering equipment trial
rental and leasing programs to assist in such testing and evaluations. Data sheets are available for valve controllers or pressure pots upon
request.

3
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
Contents
Introduction................................................................................................................................................ 4
Introduction to the User Guide ....................................................................................................................................... 4
Where to Get Help .......................................................................................................................................................... 4
Safety.......................................................................................................................................................... 4
Specific Safety Considerations......................................................................................................................................... 5
Dymax Light-Curing System Safety Considerations ......................................................................................................... 5
Product Overview........................................................................................................................................ 7
Description of the BlueWave LED DX-1000 VisiCure ....................................................................................................... 7
Special Features and Benefits of the BlueWave LED DX-1000 VisiCure System .............................................................. 8
Intensity Control Feature ................................................................................................................................................ 8
Validation ........................................................................................................................................................................ 9
Front Control Panel ....................................................................................................................................................... 10
Back Panel ..................................................................................................................................................................... 11
Assembly and Setup ...................................................................................................................................12
Unpacking and Inspecting Your Shipment..................................................................................................................... 12
Parts Included in the BlueWave LED DX-1000 VisiCure Small-Area LED Light Source ................................................... 12
System Connections ...................................................................................................................................14
Operating the LED Light..............................................................................................................................15
Powering up the Controller........................................................................................................................................... 15
Using Advanced and Optional Features.......................................................................................................16
Using the Optional Stand............................................................................................................................................... 16
Using the PLC Interface ................................................................................................................................................. 17
System Cleaning ............................................................................................................................................................ 19
Error Codes and Troubleshooting................................................................................................................21
Spare Parts and Accessories........................................................................................................................23
Options/Accessories...................................................................................................................................................... 23
Specifications.............................................................................................................................................25
Packages........................................................................................................................................................................ 25
Specifications................................................................................................................................................................. 25
Warranty....................................................................................................................................................27
Index..........................................................................................................................................................27

4
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
Introduction
Introduction to the User Guide
This guide describes how to assemble, use, and maintain the Dymax BlueWave® LED DX-1000 VisiCure® Small-
Area LED Light Source safely and efficiently.
Intended Audience
Dymax prepared this user guide for experienced process engineers, technicians, and manufacturing personnel.
If you are new to high-intensity LED light-curing systems and do not understand the instructions, contact
Dymax Application Engineering to answer your questions before using the equipment.
Where to Get Help
Dymax Customer Support and Application Engineering teams are available in the United States, Monday
through Friday, from 8:00 a.m. to 5:30 p.m. Eastern Standard Time. You can also email Dymax at
[email protected]. Contact information for additional Dymax locations can be found on the back cover of this
user guide.
Additional resources are available to ensure a trouble-free experience with our products:
◼Detailed product information on www.dymax.com
◼Dymax adhesive Product Data Sheets (PDS) on our website
◼Material Safety Data Sheets (MSDS) provided with shipments of Dymax adhesives
Safety
Before continuing with the installation, please read the following chapters of this manual for safety
recommendations and installation, operation, and troubleshooting instructions.
CAUTION! Always wear protective goggles or face shield when working near the front of the
unit, which emits high-intensity visible light!
WARNING! Always observe safety requirements!
CAUTION! Risk of electrical shock if cover is removed!
To use a BlueWave LED VisiCure system safely, it must be set up and operated in accordance with the
instructions given by Dymax. Using the system in any other manner will impair the protection of the system.
Dymax assumes no liability for any changes that may impair the protection of the BlueWave LED VisiCure
system.
Safety Recommendations
■Use the goggles provided or an approved face shield for eye/face protection.

5
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
■Long-sleeved shirts or a lab coat are recommended for arm protection. The use of opaque gloves will protect the
hands.
NOTE: The BlueWave LED VisiCure emits high-intensity light. Never look directly at the light-emitting end of
the lightguide while the unit power is on.
To learn about the safe handling and use of light-curable formulations, obtain and read the MSDS for each
product. Dymax includes an MSDS with each adhesive sold. In addition, fluid product MSDS can be requested
through the Dymax website.
Specific Safety Considerations
The BlueWave LED DX-1000 VisiCure is designed to maximize operator safety and minimize exposure to light-
curing energy. To use the unit safely, it must be set up and operated in accordance with the instructions in this
user guide. Please also read and understand the safety considerations unique to LED-curing systems as
described below.
WARNINGS! Looking directly at the high-intensity light emitted by the BlueWave LED DX-1000
VisiCure can result in eye injury. To prevent eye injury, never look directly at the high-intensity light
and always wear protective goggles (provided).
Operating the light with the Lens Cover in place can result in overheating and equipment damage.
To prevent equipment damage, never operate the unit with the Lens Cover in place.
Removing the cover from the BlueWave LED DX-1000 Controller can result in electrical shock. To
prevent electrical shock, never remove the cover from the DX-1000 Controller.
If you block the air flow from the LED Irradiator Head or Controller Cooling Fans, equipment
damage and malfunction can result. To prevent damage and malfunction, ensure there is
adequate space at the Cooling Fan Outlets to allow the free flow of air.
Dymax Light-Curing System Safety Considerations
Operators must understand these three concepts to use the LED light source safely: light exposure, high-
temperature surfaces, and bright, visible light. Each is described below.
Light Exposure
Standard Dymax VisiCure systems have been designed to primarily emit visible light (as shown in Figure 1).
Although OSHA does not currently regulate visible or ultraviolet-light exposure in the workplace, the American
Conference of Governmental Industrial Hygienists (ACGIH) does recommend Threshold Limit Values (TLV’s) for
ultraviolet light. The strictest interpretation of the TLV (over the UVA range) for workers’ eyes and skin is
1 mW/cm2(intensity), continuous exposure. Unless workers are placing bare hands into the curing area, it is
unusual to exceed these limits. To put the 1 mW/cm2limit into perspective, cloudless summer days in
Connecticut regularly exceed 3 mW/cm2of UVA light, which includes the more dangerous UVB light, primarily
responsible for sun tans, sun burns, and skin cancer.

6
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
Figure 1. Light Spectrum
Checking the Workstation
A radiometer should be used to measure stray light to confirm the safety of a visible light-curing process. A
workstation that continuously exposes an operator to more than 1 mW/cm2of UVA light should be
redesigned.
Protecting Operators
Light-curing technology can be a regulatory compliant, "worker-friendly" manufacturing process when the
proper safety equipment and operator training is utilized. There are two ways to protect operators from
visible light exposure: shield the operator and/or shield the source.
Shield the Operator
Tinted eyewear will shield the operator from high intensity visible energy, and reduce eye fatigue.
Shield the Source of the Light
Any substrate that blocks Visible light can be used as a shield to protect workers from stray light. The following
materials can be used to create simple shielding structures:
Sheet Metal –Aluminum, steel, stainless steel, etc. Sheet metal should be coated black or black anodized to
minimize reflection of UV and visible light toward operators.
Rigid Plastic Film –Transparent or translucent/light-blocking plastics (typically polycarbonate or acrylic) are
commonly used to create shielding where some level of transparency is also desired.
Flexible Film –Translucent light-blocking, flexible urethane films can be used to quickly create workstation
shielding. This light-blocking, flexible urethane film is available from Dymax. Call for assistance.
High-Temperature Surfaces
Surfaces exposed to high-intensity curing lights may rise in temperature. The intensity, distance, exposure
time, cooling fans, and composition of the surface can all affect the rise in surface temperature. In some cases,
exposed surfaces can reach temperatures capable of producing a burn or causing damage to a substrate. In
these cases, care must be taken to ensure either a more moderate surface temperature or appropriate
protection/training for operators. No infrared radiation is produced by these LED systems, so surface
temperatures will be lower than with conventional lamp systems. Empirical testing should be used to verify
the exact temperature rise in each application.

7
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
Bright, Visible Light
The bright, visible light energy emitted by curing systems can cause eye strain if proper eye protection or
shielding is not used. The proper use of tinted eye protection and/or opaque/tinted shielding can be utilized to
reduce eye strain and address this concern.
Product Overview
Description of the BlueWave LED DX-1000 VisiCure
The BlueWave LED DX-1000 VisiCure is a high-intensity light-curing system used for curing adhesives, coatings,
and potting materials. You can mount and integrate the unit into automated manufacturing systems or, using
the optional stand, conveniently mount and use the unit on a bench top.
The BlueWave LED DX-1000 VisiCure consists of two main components: a Controller that contains the User
Interface and Power Supply, and an LED Irradiator Head. A cable connects the two components (Figure 2).
The unit can be operated in timed or manual modes. The output intensity level can be adjusted from 0 to
100% to meet process and adhesive requirements. The BlueWave LED DX-1000 VisiCure is rated for
continuous operation.
Fans in the Controller and Irradiator Head provide cooling and must not be covered or blocked. Fan Filters
must be maintained regularly to ensure reliable operation.
Thermal Sensors in the Controller and Irradiator Head shut the unit down to protect the components if the
internal temperature exceeds maximum limits.
Figure 2. Main Components of a BlueWave LED DX-1000 VisiCure
LED Irradiator Head
Controller
Interface Cable
Light Source with Lens Cover
Optional Stand with Mounting Post
(ordered separately)

8
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
Special Features and Benefits of the BlueWave LED DX-1000 VisiCure
System
The Dymax BlueWave LED DX-1000 VisiCure is engineered for precise performance and long service life.
Key features include:
Feature
Benefit
Curing area up to 1" x 1.5"
[2.54 cm x 3.81 cm]
Area-cure capability with LED
Flexible mounting options
Adaptable to a variety of process and fixture scenarios
100% duty cycle capability
Highest throughput (exposure cycles “at the speed of light”)
No mechanical shutter
Instant on/Instant off exposures
Intensity output adjustment
(5 to 100%)
Superior accuracy over “closed loop feedback" or auto-adjusting units
Optimum process control
405 nm LED
High photo-initiator sensitivity
Co-optimized to cure
with Dymax formulations
Compatibility with many formulations
Fewer re-qualifications
Multiple energy delivery configurations
Direct emission
Lightguide
Multi-lens optical stacks
Stable LED temperature
Optimizes cure time efficiency
Increases LED life
LED
Superior LED cooling for consistent frequency output
Longer LED life via reduced intensity degradation
Intensity Control Feature
The components used in all light-curing systems degrade with use. Therefore, the maximum intensity
decreases as exposure hours accumulate. Setting process intensity requirements lower than the maximum
enables the BlueWave LED DX-1000 VisiCure’s Intensity Control Feature to allow for compensation of gradual
decreases in light intensity.
The unit's intensity can be adjusted using the Intensity Control Feature (Figure 3) on the Front Control Panel.
The intensity adjustment is software controlled and allows for control of output intensity. The ten LED Power
Level Bars correlate to 10% increments of the total available power. Pressing the up button (▲) increases the
light intensity in 1% increments. Pressing the down button (▼) decreases the light intensity in 1% increments.
As the power level is adjusted, the Cycle Time Display changes and displays the power level percentage.
Adjustment of the power setting is done while in manual mode and is not possible while running a timed
exposure.

9
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
Use a Radiometer to correlate the percent power output to a reading in W/cm2. The adjustment of power
level and correlation to a light-intensity value (W/cm2) enables precise control of light intensity during
validation and operation.
Figure 3. Intensity Control Feature on the BlueWave LED DX-1000 VisiCure
Validation
Tests should be conducted prior to production to determine the time and light intensity required to fully cure
your resin. The following approaches may be used to validate the curing process.
Set Exposure Time, Determine Intensity
Users can specify a cure time, and through empirical testing, determine the intensity required to achieve a full
cure. As with any manufacturing process, it is advisable to incorporate a safety factor.
Set Intensity, Determine Exposure Time
Users can specify light intensity and through empirical testing, determine the exposure time required to
achieve a full cure. As with any manufacturing process, it is advisable to incorporate a safety factor.
Control
Process validation confirms a minimum acceptable intensity. Users can then choose to operate at full intensity
(using the excess intensity as an additional safety factor) or adjust the output to a specific intensity level. To
ensure consistent and repeatable process results, intensity levels should be monitored with a Radiometer. This
enables users to identify light intensity changes and take corrective action: either adjusting the light intensity
or performing maintenance.
LED Power Level Bars
Light Intensity Up Button
Light Intensity Down Button

10
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
Front Control Panel
In addition to the Light Intensity Control Feature, the Front Control Panel (Figure 4) includes:
■Run/Stop Button —Pressing this button starts a curing cycle. In timed operation, pressing and releasing
the Run/Stop Button illuminates the curing light for the length of time displayed in the Cycle Time Display.
A second press will stop the cure cycle immediately. In manual operation, pressing and holding the
Run/Stop Button illuminates the curing light until the button is released. The curing light illuminates until
the cycle time is reached.
■Timed/Manual Button —Pressing this button toggles between manual and automatic operation. In timed
operation, pressing the Run/Stop Button illuminates the curing light for the length of time displayed in the
Cycle Time Display. In manual operation, the Cycle Time Display changes to a series of dashes and the
curing light remains illuminated as long as the Run/Stop Button is depressed.
■Cycle Time Display —This LED display indicates the current cycle time. It also displays the light intensity
percentage when light intensity is adjusted. It also will display error codes if an operating error occurs.
■Cycle Time Adjustment Buttons —Pressing these buttons increases or decreases the cycle time. Hold
the button in to increase the speed at which the value changes.
■Intensity Control Feature —Enables manual control of the light intensity (see Intensity Control Feature
on page 8). Pressing the + or –button momentarily will change the display to show the current setting in
%, holding the button will increase or decrease the setting and the display will show the set level as it is
adjusted.
■Operating Time Log (unit operation and exposure hours (non re-settable)) —This display is only visible
when both the + and –time buttons are pressed and held simultaneously for 5 seconds. The display will
indicate in hours the accumulated run time of the LED first and then the Controller second.
Figure 4. Front Control Panel
Intensity Control
Feature. See Intensity
Control Feature on
page 8.
Cycle Time
Adjustment
Buttons
Run/Stop Button
Timed/Manual
Button
Cycle Time &
Digital Intensity
Display

11
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
Back Panel
The Back Panel (Figure 5) includes these components and connection points:
■Power Cord Receptacle —Connection point for the Power Cord.
■I/O (On/Off) Switch —Moving the switch to the I (on) position powers up the Controller. Moving the
switch to the O (off) position cuts power to the Controller.
■Cooling Air Intake —Cooling air enters the Rear Intake, which includes a replaceable Filter. NOTE: The
exhaust vents located on the side of the enclosure must not be blocked or the unit may overheat and
shutdown.
■Footswitch Jack —Connection point for the Footswitch. Pressing the Footswitch starts a curing cycle. In
timed operation, pressing and releasing the Footswitch illuminates the Curing Light for the length of time
displayed in the Cycle Time Display. A second press will terminate a timed cure cycle immediately. In
manual operation, pressing and holding the Footswitch illuminates the Curing Light until the Footswitch is
released.
■PLC Connector —Connection point for a user-supplied cable to connect the unit to a PLC for remote
operation. Connection is a standard 15-Pin D-Style Connector. Refer to page 19 for details on the
connections to this port.
■Irradiator Head Cable Connector —Connection point for the Power Cable connecting the Controller to
the Irradiator Head.
Figure 5. Back Panel Controls and Connections
Power Cord
Receptacle
I/O Switch
(On/Off Power)
Footswitch Jack
PLC Connector
Irradiator Head
Cable Connector

12
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
Assembly and Setup
Unpacking and Inspecting Your Shipment
When your BlueWave LED DX-1000 VisiCure arrives, inspect any boxes for damage and notify the shipper of
box damage immediately.
Open each box and check for equipment damage. If parts are damaged, notify the shipper and submit a claim
for the damaged parts. Contact Dymax so that new parts can be shipped to you immediately.
Check that the parts included in your order match those listed below. If parts are missing, contact your local
Dymax representative or Dymax Customer Support to resolve the problem.
Parts Included in the BlueWave LED DX-1000 VisiCure Small-Area LED
Light Source
The BlueWave LED DX-1000 VisiCure is available in four packages:
■Base System: For custom mounting and system integration (mount supplied by user)
■Flood Lamp Package: Includes all parts necessary for using this system as a small-area flood lamp
■Spot Lamp Package: Includes all parts necessary for using this system as a spot lamp
■Lab Developer Package: Includes all parts necessary for both spot and flood modes
Figure 6. BlueWave LED DX-1000 VisiCure Components

13
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
Table 1. Parts List
#
Part
Base System
Flood Mode
Package
Spot Mode
Package
Lab Developer
Package
41046
41047
41048
41049
41051
41052
41053
41055
41056
41057
1
Irradiator Head with Collimating Optic #1




2
Controller




3
Interface Cable - Choice of 3, 6, 10, or 19 in length

Interface Cable –19 in



Interface Cable –3 in

4
Footswitch




5
Power Cord*




6
Filter Media




7
Hex Key




8
UV Protection Goggles




9
3-PC Magnetic Flexible Shielding




10
Benchtop Stand and Work Platform



11
Benchtop Base


12
Lightguide Adapter


13
Lightguide Mounting Stand


13
Lightguide, 5 mm x 1 M


BlueWave LED DX-1000 VisiCure User Guide




* Dependent on model ordered. Some models do not include a power cord.

14
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
System Connections
Figure 7. Installing Cables on the Back Panel of the Controller
Figure 8. Attaching the Irradiator Head to the Optional Stand
Figure 9. Installing Cable on the Irradiator Head
Irradiator Head
Interconnect
Cable
Footswitch Jack
and Connection
Power Cord
Irradiator Head Support
Arm (Included with
Optional Stand)
Irradiator Head
Irradiator Head Cable
Connection Point

15
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
Operating the LED Light
WARNINGS! Looking directly at the high-intensity light emitted by the BlueWave LED
DX-1000 VisiCure can result in eye injury. To prevent eye injury, never look directly at the high-
intensity light and always wear protective goggles (provided).
Operating the light with the lens cover in place can result in overheating and equipment damage.
To prevent equipment damage, never operate the unit with the lens cover in place.
Powering up the Controller
Follow these steps to operate the BlueWave LED DX-1000 VisiCure system:
1. Move the Power Switch on the Back Panel of the Controller to the On (I) position. The Power Supply
and Timer are now operational.
2. Activate an exposure cycle by pressing the Footswitch or the Run Button on the Controller Front
Panel (Figure 10).
3. In manual mode (all timer digits will be dashes), the exposure time is controlled directly from the
Footswitch. In timed mode, operation is determined by the setting displayed on the Cycle Time
Display.
4. To adjust the exposure time, push the Cycle Time Adjustment Buttons (Figure 10) to enter the desired
number of seconds the LED needs to be powered. The up arrow () increases the cycle (exposure)
time in 0.1 second increments. Note that holding the up arrow increases the rate of change of the
digits. The down arrow () decreases the cycle (exposure) time in 0.1 second increments.
5. The output intensity can be adjusted from 5 to 100% in 1% increments using the light intensity up
arrow (▲) or down arrow (▼). Press the Timed/Manual Mode Button to place the unit in manual
mode and then adjust the intensity using the Intensity Adjustment Buttons. Output intensity cannot
be adjusted in the timed mode.
Figure 10. Front Control Panel
Intensity Control
Feature. See Intensity
Control Feature on
page 8.
Cycle Time
Adjustment Buttons
Run/Stop Button
Timed/Manual
Mode Button
Cycle Time Display

16
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
Using Advanced and Optional Features
Using the Optional Stand
You can purchase an optional stand that enables convenient and efficient use of the BlueWave LED DX-1000
VisiCure on a bench top.
To assemble and use the stand, follow these steps:
1. Attach the Upright to the Stand Base Unit using the Bracket and M6 hardware supplied (Figure 11).
2. Attach the Irradiator Head unit to the Irradiator Head Support Arm using the two M5 x 10 mm
Mounting Screws and the 3 mm hex wrench.
3. Place the Stand Base Unit over the BlueWave LED DX-1000 Controller.
4. Adjust the height of the Irradiator Head Support Arm using the locking Height Adjustment handle on
the Irradiator Head Support Arm (Figure 12).
Figure 11. Assembling the Optional Stand, Back View
Figure 12. Assembling the Optional Stand
Height Adjustment Handle
Stand Base Unit
Upright
Attachment Point for Irradiator Head
Irradiator Head Support Arm
Work Pad
Bracket and M6 Screws
Upright
Stand Base Unit

17
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
Using the PLC Interface
The BlueWave LED DX-1000 VisiCure includes a 15-Pin D-Subminiature Connector for communication with a
PLC or similar process control equipment. The connector provides for input and output signals.
Table 2. Pinouts for 15-Pin D-Subminiature Connector on BlueWave LED DX-1000 VisiCure
Pin Number
Name
Description
1
+24V input
If this input is not present, ignore all PLC inputs and allow the outputs to run
as usual.
2
Power supply and
signal common
Return for all signals on the on the PLC.
3
Sleep input
With 24V applied, disables all functions on the Front Panel, Footswitch, and
PLC Inputs. Shuts down the Fan completely after cooling the LED. Disables
the LED Displays except for the Scrolling Display Panel to indicate sleep
mode. If this signal is initiated during a cure cycle (duration >20 min.) the unit
will terminate the current cure cycle and go into sleep mode.
4
Interlock input
Allows operation of the unit in the PLC mode only if this signal is present. If a
safety switch is used then a failure (mode) in the switch or cables will
terminate the operation of the unit.
5
Activate input
This Pin will work as the Run or Footswitch activation at the current intensity
level (will be used for “simple” remote control of the unit when there is no
desire to vary intensity) and place the unit in manual mode. The PLC will
dictate cycle duration. The Cycle Time Display will indicate all dashes. When
this signal is terminated the unit will remain in manual mode.
6
Intensity input
This is a PWM input used to set the LED intensity and describe a running set
point. This input will work in conjunction with the Activate Input to enable
operation. The PWM base frequency shall be 1 KHz. The duty cycle will
dictate relative intensity.
7
Local disable input
When this Pin is asserted, the Footswitch and Run triggers will still be
operational, but the Front Panel Controls will be "locked out" from the user.
Activation can be accomplished but no adjustment to the mode of operation,
set point of the LED intensity, or the timer setting will be possible. This will also
prevent the ability to check system or LED operation hours.
8
Power on output
Asserted when the unit has correct AC voltage supplied and the internal
supplies are within limits.
9
LED powered
output
Asserted when the LED Power Supply is powered up, regardless of set point
(5-100% power). This activation can be either Footswitch, Front Panel
Button, or “Intensity In”.
NOTE: Verification of LED illumination should be made visually to ensure
proper operation.
10
Intensity output
This is a PWM-based signal to drive the LED. It is a confirmation of operation
for a given setting and as a relative indication of power level.
11
Fault output
This Pin is active when any critical fault conditions are met and the LED
operation is inhibited.
12
Not used
13
Not used
14
Not used
15
Not used

18
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
Figure 13. Pinout Diagram for 15-Pin D-Subminiature Connector

19
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
Cleaning and Maintenance
System Cleaning
Optic Lens
Based on the cleanliness of your operating environment, establish a schedule for cleaning the LED Light-
Source Lens. When cleaning is required, shut the unit down and allow it to cool. Then clean the Lens surface
(Figure 14) with a clean lint-free cloth and isopropyl alcohol.
Figure 14. Lens Assembly
Replace Cooling Fan Filters
One Cooling Fan Filter is located on the Irradiator Head and one is located on the Controller. The procedure for
cleaning or replacing the Cooling Fan Filter is similar on both components. One procedure is provided below.
Based on the cleanliness of your operating environment, establish a schedule for cleaning the Cooling Fan
Filter. When the Cooling Fan Filter shows signs of wear from cleaning and use, replace it with one of the spare
Filters provided with your unit. Follow these steps to wash or replace the Cooling Fan Filter:
1. Unplug the unit.
2. Remove the Filter Cover by lifting it from the Irradiator Head (Figure 15).
3. Remove the Foam Filter from the Filter Cover.
4. If the Foam Filter is serviceable, wash it with water and a mild detergent. Allow it to dry.
If the Foam Filter is not serviceable, replace the Foam Filter with a new one supplied with your unit.
5. Install a Foam Filter in the Filter Cover.
6. Install the Filter Cover on the Fan.
7. Clear the error code on the Display Screen. To clear the code, press and hold the Run Button while
turning on the power to the system.
Lens Surface

20
Dymax BlueWave® LED DX-1000 VisiCure® User Guide
Figure 15. Cooling Fan Filter Replacement
Inspect and Replace Fuses
The Controller uses two Fuses held in a Fuse Holder. Follow these steps to inspect and replace the Fuses if
indicated as a corrective action based on troubleshooting:
1. Unplug the unit.
2. Remove the Fuse Tray Cover using a small screwdriver (Figure 16).
3. Slide out the Fuse Tray using a small screwdriver.
4. Remove and inspect the Fuses.
5. Replace blown Fuses with new ones as specified in the Specifications Section.
6. Insert serviceable Fuses back into Fuse Tray.
7. Push the Fuse tray into the Power Receptacle.
8. Snap the Fuse Tray Cover back into the closed position.
Figure 16. Opening the Fuse Tray Cover (left) and Sliding Out the Fuse Tray (right)
Fuse Tray Cover
Fuse Tray
Foam Fan Filter
Fan Filter Cover
Cooling Fan