Dynacraft 24V CARRIAGE User manual

this manual contains important safety, performance and
maintenance information. read the manual before taking your
first ride or allowing your child to ride your new electric
ride-on toy. keep the manual handy for future reference.
FOR AGES 3+
MAXIMUM WEIGHT: TOTAL 130 lb (59 kg), 65 lb (29.5 kg)
PER SEAT
24V CARRIAGE
OWNER’S MANUAL
NOTE: Illustrations in this manual are for reference purposes only and may not reflect the exact
appearance of the actual product. Specifications are subject to change without notice.
DO NOT return this item to the store.
QUESTIONS OR COMMENTS?
1-800-288-1560

1
AIntroduction, Safety and Warnings . . . . . . . . . . . . . . . . 2
BBefore You Begin Assembly . . . . . . . . . . . . . . . . . . .6
CParts Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 7
DAssembly . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
EHow to Use Your Vehicle . . . . . . . . . . . . . . . . . . . . 17
FDetailed Maintenance and Repair . . . . . . . . . . . . . . . 20
GTroubleshooting Guide . . . . . . . . . . . . . . . . . . . . . 26
HWarranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
SUITABLE AGE. . . . . . . . . . . . . . . . . . . . . . . . . . .3+
CAPACITY . . . . . . . . . . . . . . . . . . . . Up to 130 lb (59 kg)
MAX SPEED . . . . . . . . . . . . . . Low 2.5 MPH / High 5.0 MPH
CHARGER / INPUT . . . . . . . . . . . . . . . . . . AC120V / 60HZ
OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . DC 24V / 1A
CHARGING . . . . . . . . . . . . . . . . . . . . . . .12–18 Hours
BATTERY . . . . . . . . . . . . . . . . . . . . 24V7AH, 1x Battery
SIZE OF CAR . . . . . . . . . . . . . . . . . 1510 x 130 x 830 mm
AVERAGE BATTERY LIFE. . . . . . . . . . . . . . . . .300 Charges
TABLE OF CONTENTS
ELECTRIC CAR SPECIFICATIONS

2
ABOUT THIS MANUAL: This manual was written to help you and your child get
the most performance, comfort, enjoyment and safety when riding your new
electric ride-on toy. It is important for you to understand your new electric ride-on
toy. By reading this manual before you let your child go out on his/her first ride,
you will know how to get the most from your new electric ride-on toy. It is also
important that you or your child's first ride be in a controlled environment, away
from cars, obstacles, and other riders.
GENERAL WARNING: Riding an electric ride-on toy can be a dangerous
activity, even under the best of circumstances. Proper maintenance of your new ride-on toy
is your responsibility and helps reduce the risk of injury. Certain conditions may cause
components to fail without fault of the manufacturer. The ride-on toy can and is intended to
move, and it is therefore possible to lose control, fall off and/or get into dangerous situations
that no amount of care, instruction or expertise can eliminate. If such a thing does occur,
your child can become seriously injured or die, even when using safety equipment and other
safety precautions.
WARNING: To reduce risk of injury, adult supervision is required. Never use in
roadways, near motor vehicles, on or near steep inclines or steps, swimming pools or other bodies of
water; always wear shoes, and never allow more than two (2) riders.
WARNING: CHOKING HAZARD-Small parts not suitable for children under 3
years old.
RIDE AT YOUR OWN RISK AND ALWAYS USE COMMON SENSE.
This manual contains many warnings and cautions concerning the consequences
of failing to inspect, maintain or properly use your electric ride-on toy. Because
any fall can result in serious injury or even death, we do not repeat the warning of
possible serious injury or death each time such a possibility is mentioned in this
manual or the risk of falling leads to a warning.
ALWAYS USE PROPER RIDING ATTIRE.
Always wear appropriate clothing and shoes. Never ride barefoot or in sandals
and make sure that shoelaces or other fasteners are tied and kept away from the
wheels and drive system of the ride-on toy.
INTRODUCTION, SAFETY AND WARNINGS A

3
RIDER USE AND REQUIRED PARENTAL SUPERVISION
RIDERS MUST NOT EXCEED THE WEIGHT LIMIT OF 130 POUNDS (59 KG)
AND MUST BE OVER 3 YEARS OLD. NEVER MORE THAN 2 CHILDREN TO
RIDE THE VEHICLE SIMULTANEOUSLY.
The age grade for the electric ride-on toy is for 3 years and older. Just because
your child is within the age and weight limitations specified for the electric ride-
on toy, does not mean that his/her size is appropriate to fit or maintain control of
the electric ride-on toy, or that he/she is capable of safely operating the electric
ride-on toy. You are the best judge of whether you or your child can safely operate
the electric ride-on toy; this includes determining whether your child is at the
appropriate developmental stage for safe use of the electric ride-on toy. Any rider
that is unable to fit comfortably on the electric ride-on toy should never attempt to
ride it. A parent's decision to allow their child to use the electric ride-on toy should
be based on the child's maturity, skill and their ability to follow rules. Remember
that the electric ride-on toy is intended for use only by children who are, at a
minimum, able to comfortably and safely operate it.
Children operating the electric ride-on toy should be supervised by an adult at all
times. Parents should ensure that children only use the electric ride-on toy safely
and within their age and physical limits.
This manual contains very important safety information. It is your responsibility to
completely review this information and make sure that all riders understand all of
the warnings, cautions, instructions and safety topics addressed in this manual
and to assure that all riders are able to safely and responsibly use the electric
ride-on toy. You should periodically review and reinforce all information in this
manual with all riders, especially children. You should also regularly inspect and
maintain your electric ride-on toy to ensure the safety of all riders. Make sure that
your new electric ride-on toy is properly fitted to any child riding it; that it is in good
repair and safe operating condition; that you and your child have gone over the
use, operation and safety information in this manual; that you and your child have
learned and understand what to do and what not to do with your new electric ride-
on toy, including observing all applicable laws, rules and common sense.
Children should be made aware of all possible riding hazards and correct riding
behavior before they ride the electric ride-on toy and should be supervised by an
adult at all times. Please explain the following to them as often as necessary.

4
SAFE RIDING PRACTICES AND WARNINGS
• Check and obey all local laws or regulations which may be in effect in the
locations where the electric ride-on toy may be used.
• Always wear appropriate clothing and shoes.
• Observe the age and weight limitations on the cover of this manual.
• Always stay seated while riding the electric ride-on toy. To stop you must take
your foot off the foot pedal.
• Children must be supervised by an adult at all times to be safe.
• Always be alert and ride your electric ride-on toy defensively. Watch out for
obstacles that could catch one of the electric ride-on toy's wheels or force you
to turn suddenly and/or lose control. Be careful to avoid pedestrians, persons
using other wheeled products (including roller or in-line skates, skateboards,
scooters, bikes, etc.), children or animals who may enter your path. Always
respect the rights and property of others.
• Do not activate the foot pedal unless you are seated in the vehicle and in a safe,
outdoor environment that is suitable for riding your electric ride-on toy.
• Do not attempt or perform any stunts or tricks on the electric ride-on toy. It is
not made to withstand such misuse and abuse.
• Keep both hands on the steering wheel at all times.
• Do not touch the motor on the electric ride-on toy when in use or directly after
use as these parts can become extremely hot.
• Never allow more than two persons to ride the electric ride-on toy at one time
and never try to tow anything.
• Do not use near steps, water, or swimming pools.
• Do not ride in wet weather.
• Never immerse the electric ride-on toy in water; electrical and drive components
could be damaged by water or create other potentially unsafe conditions.
• Keep your fingers and other body parts away from the motor, steering system,
wheels and all other moving components.
• Never hitch onto another vehicle or let yourself be pulled or pull anyone or
anything while riding the electric ride-on toy.
• Ride only on smooth, flat, dry surfaces such as pavement or level ground
without loose debris, such as sand, leaves, rocks or gravel. Water, mud, ice,
bumpy, un-even, slick, or rough surfaces could impair traction and contribute to
possible loss of control.
• Do not ride on or near hills or steep inclines. Ride only on level ground to avoid
tip over.
• Avoid sharp turns, bumps, drainage grates, and other obstacles.
• Do not ride at night or where there is limited visibility.
• Do not ride indoors or on surfaces that could become damaged such as carpet
or flooring.
• Do not ride on streets, around cars, or in foot or vehicle traffic.
• Regularly check the electric ride-on toy and its components. If any parts are
broken or worn, do not ride the electric ride-on toy until you have fixed or
replaced the broken or worn parts.

5
• Do not allow hands, feet, hair, body parts, clothing, or similar articles to come in
contact with wheels or other moving parts.
• Before each cycle of operation, you must perform the preoperation checks
specified in this manual or by the manufacturer, including:
– That all guards and pads originally supplied by the manufacturer are in proper
place and in serviceable condition;
– That the area that the unit is to be operated in is safe and suitable for safe
operation; and
– That all safety labels are in place and understood by everyone, including the
riders.
• Avoid sharp bumps, drainage grates, and sudden surface changes.
PRE-RIDE SAFETY CHECKLIST
• Check to make sure that all components are properly secured and are
functioning according to the manufacturer’s specifications.
• Components must be maintained and repaired and only with the manufacturer's
authorized replacement parts. Installation should be performed only by adult,
qualified personnel.
USING THE CHARGER
The charger should be examined regularly for damage to the cord, plug, enclosure
and other parts. In the event such damage has occurred, the electric ride-on toy
should not be charged until the charger has been repaired by qualified personnel
or replaced. Use only the supplied, recommended charger.
• Always use caution when charging.
• The charger is not a toy and should be operated by an adult.
• Never operate the charger near flammable materials or liquids, and operate the
charger in well-ventilated areas.
• Disconnect the charger and unplug it from the electric ride-on toy when not in
use.
• Do not exceed the recommended charging time.
• Always disconnect the charger from the electric ride-on toy prior to wiping
down or cleaning the electric ride-on toy with any liquid.
WARNING: Never modify or alter the electrical system. Alterations could cause a
fire or explosion resulting in serious injury or death and could also ruin the electrical system.
FAILURE TO HEED THE WARNINGS LISTED ABOVE INCREASES RISK OF POTENTIALLY SERIOUS
INJURY. USE THE APPROPRIATE CAUTION WHEN RIDING AND ALWAYS WEAR APPROPRIATE
CLOTHING AND SHOES.

6
WARNING:
Remove all packing and items from the display box.
ESTIMATED ASSEMBLY TIME
You should allow approximately 50 minutes for assembly, not including initial
charging time. Initial charging can take approximately 18 hours. (see page 14–16 for
charging information).
If you experience a problem with this product, or are missing a part, please call us
at 1-800-288-1560, rather than return this product to the store.
Please identify all parts before assembly and save all packaging material until
assembly is complete to ensure that no parts are discarded.
BEFORE YOU BEGIN ASSEMBLY
WARNING: DO NOT USE NON-ORIGINAL OR
NON-RECOMMENDED PRODUCTS WITH YOUR
ELECTRIC RIDE-ON TOY.
Altering of the original components or use of non-recommended
replacement parts may or may not be compatible with the design and
will void the warranty and may cause an unsafe condition resulting in
serious injury or death.
B

7
1. Tiara on Carriage Roof x 1
2. Carriage Roof x 1
3. Lantern x 4
4. Roof Support (Front) x 1
5. Magic Wand x 1
6. Tiara on Dashboard x 1
7. M5 Nut x 1
8. Steering Wheel Assembly x 1
9. M5 x 40 Machine Screw x1
10. Seat Back x 1
11. Rear Axle x 1
12. Moustache decoration (A) x 2
13. Moustache decoration (B) x 2
14. Plastic Body Assembly x 1
15. Driving Wheelx 2
16. Front Wheel x 2
17. Ø12 Washer x 4
18. M10 Locknut x 4
19. Axle Cap x 4
20. Battery x 1
21. Battery Cover x 1
22. Battery Box Cover x 2
23. Roof Support (Rear) x 1
24. 4 x 12 Round Head Screw x 15
25. M6 x 50 Machine Screw x4
26. M6 Nut x 4
27. Charger x 1
28. 7mm Socket Wrench (for wheels) x 2
Note: Some parts shown are assembled on both sides of vehicle.
PARTS DIAGRAM
Screwdriver
(not included)
Tools Required
Socket Wrench
(included)
28
1
2
3
4
5
7
8
10
9611
12
13
14
15
20
21
22
23
24
24
27
25 26
16
19
18 17
C

8
TOOLS REQUIRED:
ASSEMBLY
Your new vehicle requires adult assembly. Please set aside around 35 minutes for
assembly. Please identify all parts before assembly and save all packaging material
until assembly is completed to ensure that no parts are discarded.
17mm Socket Wrench
(included)
WARNING: Children can be harmed by small parts, sharp edges and
sharp points in the vehicle's unassembled state, or by electrical items. In the
unassembled state, this package contains small parts. Adult assembly is required;
children should not handle parts, or help in assembly of the vehicle.
Phillips Screwdriver
(not included)
1. FRONT WHEEL ASSEMBLY
• Remove all parts from front wheel axle.
• Gently turn the vehicle body upside
down (be careful not to scratch it).
• Adjust the front wheel axle as show, until
you hear the axle lock “click” into position
for safety.
• NOTE: When adjusting the front wheel
axle, please do not put your hand into the
solt to avoid finger pinch.
• Fit a Ø19 washer onto the axle.
• Slide a wheel onto the axle.
• Fit a Ø12 washer and M10 locknut
onto the axle, then tighten it.
NOTE: Do not over-tighten.
• Inert the axle cap.
• Repeat above operation for the front
wheel on the other side.
• Front wheel should spin freely if not,
loosen nut slightly.
Wheel Axle
Wheel Axle
Front
Wheel
Ø12
Washer
Ø19
Washer
M10
Lock Nut
Axle Cap
A
B
D

9
2. REAR AXLE ASSEMBLY
• Remove all parts from the rear axle.
• Insert the rear axle through the hole in
the vehicle body as shown, and ensure
that the rear axle is centered with left and
right ends exposed the same distance
outside of the vehicle body.
3. DRIVING WHEEL ASSEMBLY
• Slide the driving wheel onto rear axle and
make it match up with the gear box.
• Insert a Ø12 washer onto the axle.
• While holding the rear axle with a 17mm
socket wrench, fit the M10 locknut to the
end of the rear axle with another 17mm
socket wrench. DO NOT over tighten;
the rear axle ends are supposed to be
exposed; 1-2 threads exposed can be OK.
• Insert the axle cap.
• Repeat above steps on the other side to
install the other driving wheel.
Gap
IMPORTANT! CHECK WHEEL GAP
After assembling any wheel onto the axles,
make sure to check the gap between the
screw thread and the outside of the wheel
(refer to the adjacent diagram). If the gap
is too big, add two or three washers on
the axle to the inside of the wheel. After
tightening the nut on the outside of the
wheel, please spin the wheel to check
if the wheel spins smoothly. If the wheel
gets caught or does not spin smoothly, the
friction may cause damage to the motor. Try
increasing the gap by removing one or two
washers to ensure the wheel spins smoothly.
NOTE: If the wheel nuts are loose,
the wheels will not engage the
forward gear. Tighten the nut with
the socket wrench.
Rear Axle
Gear Box Hole
Rear Axle
Driving
Wheel
Ø12
Washer Axle Cap
NOTE: Actually both front and rear wheels are exactly the same, for better looking, when
mounting the wheels on, please pay attention to keep same rim cover pattern’s rotation, Left
side of carriage wheels to have same rim cover pattern’s rotation, and Right side of carriage
wheels to have same rim cover pattern’s rotation.
M10
Lock Nut

10
4. SEAT BACK ASSEMBLY
• Gently turn the vehicle body upright.
• Slide the seat back into the slots in
the plastic body as shown, push until
you hear a “click”, and use the Phillips
screwdriver to tighten with four 4x12
round head screws.
4x12 Round
Head Screw
NOTE: Make sure the streering wheel is mounted
in right direction as shown
5. STEERING WHEEL ASSEMBLY
• Insert the steering wheel onto the end of
the steering column, line up the hole in the
steering wheel and the hole in the steering
column, reinsert the M5 x 40 machine screw
and M5 nut as shown and tighten securely
with a screwdriver.
Steering
Wheel
M5x40
Machine Screw
M5 Nut
6. STEERING WHEEL BATTERIES
INSTALLATION
NOTE: Batteries are not included.
• Loosen the screw in the steering wheel and
remove the cover.
• Insert 2x1.5V size AA AM-3 or LR6
batteries as shown.
• Replace the cover and tighten the screw
to secure it in place.
Battery Compartment
Door

11
STEERING WHEEL BATTERY SAFETY INFORMATION:
Batteries may leak fluids that can cause chemical burn, injury or ruin your product.
To avoid battery leakage:
• Install batteries correctly, observing the polarity (+,-) signs to avoid leakage.
• Do not mix old and new batteries.
• Do not mix batteries of different types: alkaline, standard (carbon-zinc) or
rechargeable (Ni-MH).
• Remove the batteries from the battery compartment when the unit will not be
used for an extended period of time.
• Always remove exhausted batteries from the battery compartment.
• Do not dispose of batteries in fire.
• Do not short circuit the supply terminals.
• Replace the batteries when the horn sounds become distorted.
• Non-rechargeable batteries should not be recharged.
• Use only batteries of the same or equivalent type as recommended.
• If rechargeable batteries are used, they should only be charged by adult.
• Remove rechargeable batteries from the product before charging.
• Battery chargers used with toys must be examined regularly for damage to the
cord, plug, enclosure and other parts. In the event that such damage is found,
the toy must not be used with the battery charger until the damage has been
repaired.
• Insert and click into another set of moustache decoration into front of vehicle body.
7. MOUSTACHE DECORATION
ASSEMBLY
• Find 4 pieces of moustache decoration in
accessories pack, and distinguish them into
two sets, find one set as shown and insert
them into back of vehicle body, then resert
the M6X50 machine screw and M6 nut as
show and tighten them with a 5MM allen key.
NOTE: there are left and right side moustache
decoration, the side with screws should face
inside.
M6 X 50
Machine
Screw

12
8. REAR ROOF SUPPORT
ASSEMBLY
• Slide the rear roof support into slots in
back of vehicle body as shown, push until
it click into, then insert three 4X12 round
head screw as show and tighten them with
a screwdriver.
9. FRONT ROOF SUPPORT
ASSEMBLY
• Slide the front roof support into slots
in front of vehicle body as shown, pay
attention that the round steel rod under it
need to aim into the mounting holes, then
push until it click into,then insert four 4X12
round head screw as show and tighten
them with a screwdriver.
11. LANTERN ASSEMBLY
• Align the lantern holder with the mounting
hole on vehicle body as shown, and
tighten it with a 4x12 round head screw.
• Repeat above operation for the other three
lanterns.
• Insert the carriage roof into the slots in
the front and rear roof supports as shown
until you hear it click into, then insert nine
4X12 round head screws and tighten with
a screw driver.
10. CARRIAGLE ROOF ASSEMBLY
4X12 Round
Head Screw
4x12 Round
Head Screw
4x12 Round
Head Screw
4x12 Round
Head Screw

13
13.ROOF TIARA ASSEMBLY
• Insert the roof tiara (bigger size) into the
slots in the roof, until you hear it click into.
14. DASHBOARD TIARA
ASSEMBLY
• Insert the dashboard tiara (smaller size)
into the slots in the dashboard, until you
hear it click into.
12. LANTERN BATTERIES
INSTALLATION
NOTE: Batteries are not included.
• Unscrew the two 3X12 round head screws at
the bottom of the lantern socket.
• Take out the lantern wick and insert 2X1.5V
size AAA or LR03 batteries as show.
• Replace the socket and tighten the screws
to secure if in place.
DC 1.5V (SIZE:AAA)
DC 1.5V (SIZE:AAA)
NOTE: 1.Press the switch after assembled the batteries, the lantern will be lighting, and
re-press the switch, the lantern will be turned off in 30minutes.
2.If you forget to press the switch over 30minutes, the lantern will be automatic
power-saving model.The lantern will be turned off automatic.
3.Remove the batteries from the lantern socket when the lantern will not be used for
over one week.
4.Replace the batteries when the light is dim or not work.
Lantern Socket
Lantern Wick
3X12 Round
Head Screw

14
BATTERY CHARGING
IMPORTANT! Before first time use, charge the battery for at least 18 hours.
Charge the battery for at least 12 hours after each use of the vehicle. Never
charge the battery longer than 30 hours. Overcharging or undercharging
the battery may shorten battery life and decrease vehicle running time.
WARNING: The battery can fall out and injure a child if the vehicle tips over.
Always use the battery retainer.
15. MAGIC WAND ASSEMBLY
• Insert the magic wand into the hole inside
the dashboard tiara as shown, and push it
all the way down.
16. POWER SUPPLY CONNECTION
NOTE: The battery is disconnected for shipment to prevent the battery from draining.
• Unscrew the two screws on the battery box cover with a screwdriver and remove
the battery box cover.
• Plug the battery connector into the control model connector securely, then reset
the battery box cover with two screws.
Control
Module
Connector
4X12 Round
Head Screw
Hole
Battery
Connector
Battery

15
PREVENT FIRE
• Never modify the electrical system.
• Alterations could cause a fire resulting in serious injury and could also ruin the
electrical system.
• Use of the wrong type battery or charger could cause a fire or explosion
resulting in serious injury.
• Use of non-original components on this vehicle could cause overheating, fire or
explosion.
• The battery must be handled by adults only.
• The battery is heavy and contains sulfuric acid (electrolyte).
• Dropping the battery could result in serious injury.
• Never allow children to charge the battery.
• Battery charging must be done by adults only. A child could be injured by the
electricity involved in charging the battery.
• Never lift or carry the battery by the wires or connector, this can damage the
battery and possibly cause a fire resulting in serious injury. Lift and carry the
battery by the case only.
• Read the safety instructions on the battery.
• Examine the battery, charger and their connectors for excessive wear or damage
each time you charge the battery.
• If damage or excessive wear is detected, do not use the charger or the battery
until you have replaced the worn or damaged part.
CAUTION: Use the charger in dry locations only.
1. Plug the charger port into the input socket (the socket is at back of the carriage).
2. Plug the charger plug into a wall outlet. The battery will begin charging.
NOTE: Red LED light indicates battery is charging and a green LED light indicates
battery is fully charged. (If the lights on the charger do not light up, check the
power to the outlets.)
Charging Input
Socket
1
2

16
IMPORTANT NOTE
• The battery must be upright while charging.
• The charger is not a toy.
• Do not short-circuit the battery.
• You do not need to remove the battery from your vehicle to recharge it.
• Before charging the battery, examine the battery case for cracks and other
damage which may cause sulfuric acid (electrolyte) to leak during the charging
process. If damage is detected, do not charge the battery or use it in your
vehicle. Battery acid is very corrosive and can cause severe damage to surfaces
it contacts.
• Use only an original charger (AC 120V 60Hz) with an output of DC 24V (1A) to
charge your vehicle battery.
• NOTE TO ADULTS: Regularly examine the charger for damage to the cord, plug,
housing or other parts that may result in the risk of fire, electric shock or injury.
• If your battery is old and will not accept a charge, do not leave it in the vehicle.
Always remove a dead battery from the vehicle.
• After the first charge, recharge the battery for at least 12 hours after each use.
Never charge the battery longer than 30 hours. Charge the battery after each
use, regardless of how long the vehicle was used.
• Do not allow the battery to run down completely before charging.
• Charge the battery before storing the vehicle.
• Charge the battery at least once per month, even if the vehicle has not been
used.
NOTE:
• This product has CHARGING PROTECTION: when charging, all the functions
will be cut off.
• Initial charge - At least 18 hours, and never charge the battery longer than 30
hours.
• When the vehicle begins to run slowly, recharge the battery.
• After each use or once a month minimum recharge time 12 hours, less than 30
hours at most.
WARNING: Use the charger in dry locations only.

17
HOW TO USE YOUR VEHICLE
FOOT PEDAL
To move the car, press the foot pedal down.
To stop, take your foot off the foot pedal.
FORWARD-BACKWARD SHIFT LEVER
To move the car forward at high speed, shift the lever to “High” position.
To move the car forward at low speed, shift the lever to “Low” position.
To move the car backward, shift the lever to “Backward” position.
Forward/Backward
Shift Lever
Sound button
LED Switch
Foot Pedal
NOTE: Use low speed until you get familiar with your new vehicle.
No brakes, please do not park or ride on any slopes or steep inclines.
SOUND BUTTON
Press the sound button on the steering wheel to play sounds.
LED SWITCH
Insert the magic wand into the LED switch, the LED strip at front will light up and
blink, the gem on the magic wand will light up too.
STOP
To stop the vehicle, you must take your foot off the pedal.
E

18
DOOR OPENING INSTRUCTION
LANTERN USING INSTRUCTION
1 2
Push down the handle at front doors to open.
NOTE: Only the front doors (near the dashboard side) can be opened, the rear doors
have no function and unable to be opened.
Press the bottom button on the sockect, the lantern will light up.

19
IMPORTANT
• Always stop vehicle when changing the direction to avoid damage to the gears
and motor.
• This vehicle has an adjustable seat belt; please instruct children on how to
fasten the seat belt before using.
• Do not let any child touch the wheels or be near them when the car is moving.
• To avoid accidents, please inspect the vehicle before riding to ensure that it is in
proper working order and safe to ride.
• This toy has no brake; to stop, remove foot from foot pedal.
• Check all the screws, cap nuts and protective coverings regularly and tighten as
required. Check plastic parts on a regular basis for cracks or broken pieces.
• Your new battery must be charged for at least 18 hours before you use it in your
vehicle for the first time.
• Do not wash the vehicle with water; clean it with a cloth.
SAFETY PRECAUTIONS
• The child must have adult supervision at all times.
• Do not ride on the road, footpaths, near pools, or bodies of water.
• Do not allow children under the recommended age to ride the vehicle; please
refer to the age grading.
• Do not allow riders over the recommended weight rating or age grading to use
the vehicle.
• To stop the vehicle, you must take your foot off the pedal.
• Charging should only be done by an adult.
• An adult must teach the child how to operate the vehicle.
• Do not ride on hills or slopes, in sand or on other soft, wet, or slippery surfaces.
• Do not use a different size battery. Use only original or recommended
replacement batteries.
• The vehicle is designed to carry only maximum weight of 130lbs at a time. Never
allow more than two riders or over-load the vehicle.
• This product should be assembled and checked by adults before use.
WARNING: No brakes, please do not park or ride on any slopes or steep inclines.