EA Sports PGA TOUR Golf User manual

8/8/2005 Page 1 of 7
© 2005 GLOBAL VR, INC. All Rights Reserved. Electronic Arts, EA, and EA SPORTS are trademarks or registered trademarks of Electronic Arts Inc. in the U.S. and/or other
countries. All rights reserved. PGA TOUR is a trademark of PGA TOUR, INC. and used by permission. Global VR is a registered trademark of Global VR, Inc. All other
trademarks are the properties of their respective owners.
Installing the Externally Mounted Players' Card Dispenser on
EA SPORTS™ PGA TOUR®Golf Challenge Edition Upgrade Cabinets
Document Part #: 040-0074-01
This document describes how to install the externally mounted Players' Card dispenser.
GLOBAL VR®also offers an internally mounted dispenser (part # 90538-00), which is installed by
cutting an opening in the front of the cabinet.
Kit Contents for Part # 90541-00
Part # Description Part # Description
NA Players' Card Dispenser
Assembly with Vault 4600-0012 Wood Screws (3)
115-0003-01 DB25 Ribbon Cable 100-0021-01 Cable Ties (2)
4600-0062 DB Mounting Posts (2) PLC1.5IS8-C Screw-Mounted Cable Tie
USBIO Nytric Version 1.5 USBI/O Card
(or USBI/O Extreme Card) NA 1/4-20 x 1-1/4” Bolts with Nuts and Washers (4)
115-0074-01 Players' Card Dispenser Harness 52-6212-00 Button Plugs (2)
44-1100-01 +5/+12 VDC Power Supply* 040-0074-01 Installation Instructions (This Document)
115-0008-01 AC Power Harness* 3100-0001 Players' Cards (25)
115-0079-01 DC Power Harness* Pre-paid UPS Mailing Label for Returning
the USBI/O Card to GLOBAL VR®(for
Domestic Use Only)
*Power supply and associated harnesses are not required for Canadian cabinets.
Tools Required
• Nutdriver or Wrench
• Phillips Screwdriver
• Drill
• 1/4" and 3/4" Drill Bits
• Pencil

Page 2 of 7 © 2005 GLOBAL VR
Installing the Players' Card Dispenser 040-0084-01 8/8/2005
Procedures
CAUTION: GLOBAL VR®assumes no liability for any damage or injuries incurred while
servicing the cabinet. Only qualified service personnel should perform service and
installation of cabinet hardware.
Install the Nytric Version 1.5 USBI/O or USBI/O Extreme Card
CAUTION: To prevent electrostatic discharge (ESD) damage, handle PCBs by the edges
only and use a grounding wrist strap or similar precaution.
Important: For the card dispenser to function, the system computer MUST have a Nytric
Version 1.5 USBI/O card or a USBI/O Extreme card installed.
1. With the game running, press the Operator Button and check the Nytric Version displayed on
the Machine Menu screen. If your game already has a Nytric Version 1.5 card installed, skip
steps 3-7 below, and simply connect the DB25 ribbon cable to the existing USBI/O card.
If you do not need the USBI/O card from the kit, please leave it in its packaging and return it to
GLOBAL VR®using the included pre-paid UPS mailing label (US customers only).
2. Disconnect the cables from the system computer and remove the computer from the cabinet.
Place it on a workbench and remove the side panel.
3. Refer to Figure 1 and disconnect the power connector from the USBI/O card.
4. Remove the mounting screw that secures the USBI/O card in place and remove the card.
5. Place the removed card in the anti-static bag, padding, and box from the kit and return it to
GLOBAL VR®using the included pre-paid UPS mailing label (US customers only).
6. Connect the ribbon cable to the 25-pin connector on the version 1.5 USBI/O or USBI/O
Extreme card from the kit. The connector is keyed to connect only one way.
Note: The USBI/O card does not plug into the PCI slot in the computer.
7. Install the card in the computer and secure it with the mounting screw removed previously.
8. Re-connect the power connector to the USBI/O card.
Figure 1. Installing the USBI/O Card (Version 1.5 Shown)
9. Locate the DB25 mounting hole on the back of the computer (see Figure 2) and push out the
cover plate.

© 2005 GLOBAL VR Page 3 of 7
040-0084-01 8/8/2005 Installing the Players' Card Dispenser
10. Depending on your computer, you may need to remove the power supply to access the DB25
mounting hole, as shown in Figure 2. To remove the power supply, remove the four mounting
screws that are circled in the first part of the picture below.
Note: If you prefer, you can purchase a DB25 PC blanking plate, such as PLATE925 from
StarTech.com, that will allow you to mount the connector in an unused PCI card bay.
Figure 2. Installing the DB25 Connector on PC Rear
11. Secure the DB25 connector in the mounting hole using the two screws from the kit, as shown
in the second part of Figure 2.
12. Replace the power supply, if you removed it, and secure it with the four screws.
13. Replace the side panel on the computer and secure it with the two screws.
14. Please return the leftover USBI/O card to GLOBAL VR®in the packaging used for the
USBI/O card in the kit. A pre-paid mailing label is included for US customers.
Install the Players' Card Dispenser Assembly on the Cabinet
1. Disconnect the cabinet from AC power.
2. Determine where you want to mount the Players' Card dispenser. The dispenser can be
mounted to either side or the front of the cabinet.
WARNING: Follow all safety precautions while drilling the cabinet. Wear safety
glasses and follow safety guidelines. Be careful to avoid drilling into cables or
components.
3. Position the card dispenser on the cabinet. Open the door and mark the locations for the
mounting bolts and harness hole.
4. Inspect the inside of the cabinet before drilling to make sure that you will not damage any
harnesses or other components.
5. Drill four (4) 1/4" holes for the mounting bolts in the locations that you marked.
6. Drill a 3/4" hole for the harness in the location that you marked.
7. Install the button plugs from the kit in the harness holes on the exposed sides of the dispenser.
8. Secure the card dispenser assembly to the cabinet with the four (4) bolts, washers, and nuts.

Page 4 of 7 © 2005 GLOBAL VR
Installing the Players' Card Dispenser 040-0084-01 8/8/2005
Re-Install the Computer
1. Replace the computer in the cabinet and secure it in place.
2. Refer to the figure below to reconnect the cables.
Note: Connections are shown for computers with the PS-35BL motherboard. Connector
positioning is slightly different on the NB-32 Motherboard.
115
Com 1
To Tournament Header
(If Used)
Video Port
To Monitor
Motherboard USB Ports
OK to Use on Sytems with
NB-32 Motherboard (not shown)
DO NOT USE on Systems with
PS35-BL Motherboard (shown)
Ethernet Port
For Broadband
(If Used)
Audio Out (Green)
To Audio Amp
Video Card
Modem
Phone
(Not Used) Line
to Modem Line Out
USBI/O Card
USBI/O DB37 Port
To SmartCard
Dispenser and
Player Controls
USB Port on USBI/O Card
To PCI USB Port
Game Dongle
Computer VGA Port
DO NOT USE
PCI USB Port
To USBI/O Card
PCI USB Card
PCI USB Port
To SmartCard Reader
AC Power In
USBI/O DB25 Port
To SmartCard
Dispenser
Computer Rear Connections Shown with PS-35BL Motherboard
Figure 3. PC Cable Connections

© 2005 GLOBAL VR Page 5 of 7
040-0084-01 8/8/2005 Installing the Players' Card Dispenser
Install the Power Supply (as Needed)
Note: Skip this section for Canadian cabinets with electronic coin mechs. They already have a
DC power supply installed.
1. Connect the two harnesses to the +5/+12 VDC power supply as shown below:
H ARJ
LED
DC Power Supply
Part #: 44-1100-01
Pot
4-Pin power connectors
AC
(N) AC (L) FG -12V 1A +12V 1A GND +5V
15A
GND
Set Input Voltage (115 or 230)
through hole in top.
+12V
(Yellow) GND (Black) +5V (Red)
GND
(Black)
To AC
Power Strip
White GreenBlack
Part #:
115-0008-01 Part #:
115-0079-01
To Harness
Part #:115-0074-01
Figure 4. DC Power Supply Wiring
2. Position the power supply in the cabinet and secure it with the two wood screws from the kit.
3. Connect the power harness (part # 115-0008-01) to the AC power strip.
Connect Harnesses
1. Run the 6-pin connector on the card dispenser harness (Part # 115-0074-01) through the
harness hole, and connect it to the card dispenser.
2. With the card dispenser open, use a screw-mounted cable tie to secure the harness to the inside
of the cabinet so that it will not be caught or pulled when the dispenser is opened.
3. Refer to Figure 6 for a simplified wiring diagram. Disconnect the DB37 connector from the
USBI/O card in the computer, and connect it to the corresponding connector on the Players'
Card dispenser harness. Use two cable ties to secure the two DB37 connectors together, as
shown in the picture below.
Figure 5. Securing the DB37 Connectors
4. Connect the other DB37 connector on the dispenser harness to the DB37 port on the USBI/O
card in the computer.

Page 6 of 7 © 2005 GLOBAL VR
Installing the Players' Card Dispenser 040-0084-01 8/8/2005
5. Connect the DB25 connector on the dispenser harness to the connector that you installed in the
computer.
DB37 Port on
USB I/O Card in
System Computer
Existing Harness to Cabinet
Components
+5/+12 VDC In From Power Harness
To SmartCard Dispenser
SmartCard Dispenser Harness
(Part # 115-0074-01)
DB25 Port on
USB I/O Card in
System Computer
Figure 6. Card Dispenser Simplified Wiring Diagram
6. Connect the PC power connector on the dispenser harness to the +12/+5 VDC power harness
from the DC power supply.
7. Insert the desired number of Players' Cards in the dispenser, as shown below.
Figure 7. Filling the Players' Card Dispenser
8. Power ON the cabinet and test the dispenser from the System Test screen of the Game
Operator Menu. Set Players' Card pricing from the Game and Coin Options menu.
9. Test all game functions to verify proper operation.
Note: The dispenser will not work unless it is fully closed and in a vertical position (no more than
a 5-degree angle), with the back cover in place.
Rebooting the computer without power cycling the cabinet may cause the Players' Card
dispenser to dispense a card.

© 2005 GLOBAL VR Page 7 of 7
040-0084-01 8/8/2005 Installing the Players' Card Dispenser
YEL
BLU
BLK
BLK
3
4
RED
BLU
YEL
ORG
BLU
BLK
GRN
VIO
GRY
WHT-BLU
Spare
Spare
GRN
VIO
RED 1
2
1
3
4
2
Trackball
WHT
RED
BLK
Coin Counter
Lamps
Coin Switch 1 Coin Switch 2
BLK
RED
3
4
1
2
1
3
4
2
Harness PN:
GLO-01111-02
3
4
1
2
7
8
5
6
9
Bill
Validator
WHT
BLK
115 VAC
2
3
4
1
5
7
8
9
10
11
17
18
26
27
28
30
31
35
20
21
22
23
29
2
3
4
1
5
7
8
9
10
11
17
18
26
27
28
30
31
35
20
21
22
23
29
Encoder 1B 2
Ground 3
Encoder 2B 4
Ground 1
Ground 5
USBI/O Extreme
DB37 Port
+5 VDC 7
Shot Type Button 8
Fly Over Button 9
Right Turn Button 10
Coin Line 0 11
+5 VDC 17
Ground 18
Ground 26
Left Turn Button 27
Start Button 28
Coin Line 1 30
Ground 31
Coin Counter 35
Encoder 1A 20
+5 VDC 21
Encoder 2A 22
+5 VDC 23
Operator Button 29
BLK-WHT
RED-WHT
YEL-WHT
RED-WHT
BLK-WHT
GRN-WHT
VIO-WHT
BLU-WHT
GRY-BLU
GRY-YEL
GRY-ORG
GRY-GRN
GRY-VIO
BLK-WHT
WHT-YEL
BLK-WHT
WHT
BRN
GRY
USBI/O Extreme
DB25 Port
6
5
Error (DINB2) 6
Ready (DINB0) 5
236Ground 36
Dispense (DPWROUT2) 16 16
(DOUT1) 32 32 4
WHT-BRN 3
2
1
WHT-ORG
WHT-VIO
4
3
37+12 VDC 37
BLK
YEL Audio Amp Power (12 VDC)
36
37
1
6
5
BLK-
WHT
Power in from DC
Power Supply
To SmartCard Dispenser
Harness PN:
115-0074-01
2
3
4
1
5
7
8
9
10
11
17
18
26
27
28
30
31
35
20
21
22
23
29
36
37
2
4
3
1
4
3
2
1
6
5
YEL
RED
BLK
BLK
+12 VDC
+5 VDC
GND
GND
RED
BLK
BLK
RED
9
8
3
2
6
5
4
7
9
8
3
2
6
5
4
7
3
2
1
4
6
5
3
2
1
4
6
5
Operator
Button
Player Control
Buttons
BLK
Figure 8. Cabinet Wiring Diagram with Card Dispenser