Notes for assembly:
@&/,4(99,3)204.62(9:0*9620:92,,<,954:5659:9),9;8,:/,:/0*1,86(8:5-:/,:(6,8.5,9:5=(8+:/,)5::53(1,
9;8,:/,80)0490+,9620:92,,<,099,(:,+04:5.855<,54:/,659:
@&/,4049:(2204.90+,+-8(3,9/,2<,9(4+35;9,9/,2-952+9,6(8(:,2?),9;8,:/,:/0*1,86(8:5-:/,*522(89.5,9
:5=(8+:/,)5::53
C659:9
C
659:9
Figure 1b
90+,+
-8(3,
Install 3-sided frame
1
a) Assemble plastic split
sleeves onto 2˝ mark on all
posts (see Figure 1a).
b) Insert posts throu h collars
of 3-sided frame as shown
in Figure 1b. Slide 3-sided
frame down onto split
sleeves. 33˝ posts should
indicate front of unit.
Note: Bottom of
each post is
the end with
roove 17/16˝
from the end.
9620:
92,,<,9
C3(81
Figure 1a
Assembly is complete.
C
659:9
Figure 5
*(4:02,<,89/,2-
Install 12˝ x 24˝ cantilever shelf
5
a) Assemble split sleeves onto
48˝ mark on 48˝ posts.
b) Insert 48˝ posts throu h
cantilever shelf collars and
slide shelf down onto split
sleeves (see Figure 5).
Install 14˝ x 24˝
wire undershelf
a) Assemble plastic split
sleeves onto topmost mark
on both 7˝ posts.
b) Assemble wire shelf to
7˝ posts (see Figure 2a).
c) Assemble plastic split
sleeves onto 9˝ mark
on 48˝ posts.
d) Insert the 48˝ posts
throu h remainin
undershelf collars and
slide assembly down
onto split sleeves.
7˝ posts should rest
on 3-sided frame
(see Figure 2b).
2
Figure 2a
=08,;4+,89/,2-
C 659:9
C
659:9
;4+,8
9/,2-
90+,+
-8(3,
Figure 2b
Install 24˝ x 24˝ wire shelf tabletop
a) Assemble split sleeves onto 32˝ mark on all posts.
b) Position shelf over 4
vertical posts and
slide down until shelf
collars seat on plastic
split sleeves.
Note: Shelf trusses
should run left-to-ri ht
as shown.
4
Figure 4
C
659:9
C>C
9/,2-
Figure 3
35;9,6(+
Install mouse shelf (sold separately)
3
a) Assemble split sleeve onto 29˝ mark on
either left or ri ht 33˝ post (see Figure 3),
dependin on preference.
b) Slide the mouse shelf collar down the post
and onto split sleeve. Mouse shelf should
be able to swivel on split sleeve and post.
C659:
9620:92,,<,
Note: Install casters with brakes onto
the 33˝ posts.
a) Gently lay unit on its side or back,
ivin access to bottom of posts.
b) Install donut bumper onto bottom
of each post.
c) Insert caster stem into bottom of
each post. Drive caster in, usin a
hammer or mallet. Several solid
hits are usually required.
659:
+54;:
);36,8
*(9:,8
9:,3 Figure 7
7
Assemble casters to posts
Figure 6
Install keyboard drawer
6
a) Position
keyboard drawer
under tabletop.
b) Hook drawer
slides over
outermost front-
to-back trusses
of tabletop on
each side.
1,?)5(8+
+8(=,8
:()2,:56
9/,2-
:8;99
(.2,55+9,8<0*,7;063,4:(.2,(4+"6,*A(8,+0<0905495-(.2,85;6B)?:/,(.2,85;6
• 100 Indu trial Boulevard, Clayton, Delaware 19938-8903 U.S.A.
• Phone: 302/653-3000 • 800/441-8440
• Fax: 302/653-2065 • www.eaglegrp.com
(End)
