EasyFold PRO 2.0 User manual

Welcome 1
EasyFold PRO 2.0 Model Components 2
Specifications 3
Specification Diagram 4
General Safety 5
Maintenance 7
Install Setup 8
Controller 11
Basic operation 12
Charging Batteries 14
Free Wheel Mode 17
Transporting Your EasyFold PRO 2.0 18
Trouble Shootings 19
Diagnostics 20
Warranty 21

Congratulations on choosing the EasyFold PRO 2.0! You are now officially part of the EasyFold
family. The EasyFold PRO 2.0 will provide you with years of dependable service, with proper use
and care.
This manual is to assist you in operating and maintaining your EasyFold PRO. Please fully read and
understand all sections of this manual before operating your EasyFold PRO. After reading the
manual, if you have any questions or concerns, please feel free to contact us.
Do not attempt to charge or operate this vehicle until you have attained adequate knowledge of its
features and controls. Failure to operate the unit safely could result in serious injury or death and/or
damage to the vehicle and/or denial of warranty coverage.
In our constant efforts to improve and upgrade our products, your EasyFold PRO may incorporate
updated components and/or features that are not specifically covered by this version of the Owner’s
Manual. If you are not clear on how to operate or make use of any components or features, contact
EasyFold Canada for clarification. Product design, features, and specifications are subject to
change without notice.
We strongly believe that your new EasyFold PRO will provide you with the independence and
convenience that you have been looking for!
EasyFold Canada
Located in London, Ontario
1-855-444-8488
[email protected]
Disclaimer
EasyFold, its affiliates and partners, cannot be held responsible for personal injury or property
damage resulting from unsafe and improper operation or maintenance of the EasyFold portable
power wheelchair.
EasyFold Canada believes in constantly enhancing the product and its accessories for better
results. As a part of this ongoing product enhancement program, EasyFold has the right to change
specifications and design without notice. This may result in minor differences between the
EasyFold, its accessories and the photos, illustrations and instructions in this manual.

EasyFold PRO 2.0 Model Components
EasyFold - Pro 2.0 Model
A redesigned frame provides the EasyFold PRO 2.0 model with a higher maximum carrying
capacity (396 lbs), more seating room, and a higher top speed.
EasyFold PRO is composed of a very durable lightweight aluminum alloy, with 7.5” front wheels, 12″
rear wheels and two 250 Watt Brushless HUB motors to power them. You will be amazed at how
effortless it is to quickly fold this chair to a compact size. Unfolding is just as easy! The EasyFold
PRO comes with two removable LifePO4 Lithium-ion, 24V 6aH batteries and a maximum speed of 8
km/h.

Specifications
Model
EasyFold Pro 2.0
Material
Aluminum alloy
Unfold Size
940*650*975mm
Fold Size
650*350*775mm
Loading Capacity
150kg
Motor
250W*2pcs brushless motors
Battery
24V 6AH*2 pcs lithium battery
Max Speed
6km/hour
Driving Range
22KM
Front Wheels
8”*1.25” PU solid wheels
Rear Wheels
12.5”*2.125” PU solid wheels
Maximum Suggested
Climbing Slope
max 8°
Charging Time From
Empty
6-8 hours
Width of Armrest
510mm
Seat Width
470 mm
Seat Depth
400 mm
Seat Height
front 490mm/ back 470mm
Turning Radius
850mm
Net Weight Without
Battery
25.2kg
Net Weight With Two
Batteries
27.8kg
Drive Model
rear drive
Braking System
electromagnetic brake


Specification Diagram

General Safety
The safety of our customers is very important to us, so it is recommended to review the safety
instructions carefully. Always operate the EasyFold PRO, safely and according to directions. Should
you have any questions, please email [email protected] or call toll free 1-855-444-8488.
How to Read this Manual:
A “WARNING!” label indicates that failure to abide by the
following instructions may result in serious personal injury or
death to the rider or others, as well as damage to equipment.
A “CAUTION!” label indicates that failure to abide by the
following instructions may result in damage to your EasyFold and
related equipment and/or legal consequences and/or fines and/or
denial of warranty coverage.
A “Note:” label indicates information that is especially useful but
does not have safety consequences.

General Safety Procedures
Adjust EasyFold PRO wheelchair to your personal comfort level as much as possible.
Take time to learn how the EasyFold PRO operates in a private space before operating
outdoors/large spaces.
Practice bending, reaching and transferring in and out of the EasyFold PRO.
Always be aware of your surroundings when operating.
If unsure as to whether the EasyFold PRO can surpass an obstacle, find an alternate route.
The EasyFold PRO is designed for a single user only; more than one user may result in personal
injury.
Ensure components such as the joystick, battery charger and other electronic components avoid
moisture.
If components come into contact with moisture, dry it before use.
The EasyFold PRO seat is designed for comfort, not specifically for pressure relief; if any concerns,
please consult a physician.
Pre-Operating Safety Procedures
It’s important to maintain the EasyFold PRO. Failure to maintain could increase risk for injury.
Before sitting, make sure the EasyFold PRO is turned OFF. This will ensure the EasyFold PRO will
not move upon transferring on and off the unit.
Ensure the footrest is down.
Make sure feet are safely rested on the footrest.
Check for any unusual noises, vibration, or changes in the ease of use; if a problem is detected, use
the tool kit to perform maintenance or get in touch with us directly through phone or email.

Operating Safety Procedures
Always remain alert and aware of motor vehicles on roads or in parking lots.
At night, or when it is difficult to see, it is suggested to use reflective tape on the EasyFold PRO.
EasyFold PRO is designed for use on firm, even surfaces such as concrete, asphalt or indoor
flooring.
Do not operate the EasyFold PRO in sand or loose soil. This could damage the wheels, bearings,
axles or motors, and may loosen fasteners.
Safe Exit Procedures
Ensure that you bring the EasyFold PRO to a full and complete stop, prior to exiting.
Turn OFF the unit to avoid the wheelchair moving when transferring.
Raise the armrest carefully and transfer from the seat.

Maintenance
It is important to perform regular maintenance of your EasyFold PRO 2.0 for longevity and warranty
eligibility. Even a little cleaning now and then will go a long way to keep your device looking and
functioning like new.
Certified repair shops with trained professionals who specialize in electric wheelchairs and scooters
will be qualified to perform the service and maintenance on your EasyFold PRO 2.0.
We recommend you inspect your EasyFold two or three times per year in the following areas:
(1) Frame: Tighten loose screws as necessary using the tool kit included with your EasyFold
PRO 2.0.
(2) Wheels: Make sure they rotate easily. Significant resistance may require new bearings.
(3) Armrest: Look for excessive wear or if they are loose.
Replacement parts and more major maintenance issues should be done by a professional.
◎ Batteries
(1) Use batteries that have been supplied by EasyFold; our batteries are special lithium
batteries designed specifically for use in the EasyFold PRO 2.0.
(2) Read all battery instructions before attempting to change or charge batteries.
(3) When you haven’t driven the wheelchair for a long time, please ensure the battery is
charged once every month to avoid decreasing battery life.
◎ Fasteners
Many of the screws, bolts and nuts on the PRO 2.0 are special high-strength fasteners. Replacing
these fasteners with non-approved parts may cause your Fold Power Wheelchair D10 to result in
faulty operation and may cause harm to you or other people, therefore:
A. Use fasteners that have been supplied by EasyFold.
B. Using the tools included with your EasyFold PRO 2.0, tighten any fasteners that become
loose as soon as possible.
◎ Change and Adjustments
Never use non-EasyFold PRO 2.0 parts or make changes to your PRO 2.0 unless authorized in
writing by a representative from our company. Doing so will void the warranty and may create a
safety hazard.



Electromagnetic Interference
The EasyFold PRO 2.0 may be susceptible to electromagnetic interference, which is interfering
electromagnetic energy emitted from sources such as radio stations, TV stations, amateur radio
transmitters, two-way radios, and cellular phones. The interference (from radio wave sources) can
cause the EasyFold PRO 2.0 to release its brakes, move by itself, or move in unintended directions.
Install Setup
Your EasyFold PRO 2.0 will arrive carefully packaged in a cardboard box with thick foam padding.
1. Open the top of the box then turn the box on its side for easier unpacking.
2. Components included in your box:


3. To expand the EasyFold PRO 2.0, grasp the push bar and pull up while holding down on the
seat to expand the chair and complete the assembly:
4. Sit on the chair and lean backwards to make sure the clip locker, which is located below the
seat to the rear of the EasyFold PRO 2.0, has locked the seat into place.
5. Install the controller into the open slot on the arm of the chair, on the right side (if the user
needs, this can be changed to the left side). Tighten the knob located under the armrest to secure
the controller in place.
6. Connect the controller wire harness to the CPU wire harness. Take care that the pins line up
properly as the arrow indicates, so that they do not get bent, broken or damaged.

7. Insert two batteries and push to the back of the battery holder.


Controller
The EasyFold PRO 2.0 is equipped with a joystick style controller.
◎ Controller and Driving Tips
1. Take some time in a safe, controlled environment to learn the operation of the controller, the
speed and the maneuverability of the wheelchair.
2. When turning, reduce your speed; this will help you avoid any potential tilting or tipping of the
wheelchair.
3. Be sure to adjust the speed depending on your environment.
4. To slow down, slowly bring the joystick back toward the initial position.
5. To stop, bring the joystick back to the initial position.
6. Use extra care when you drive the EasyFold PRO 2.0 in reverse. You may lose control or fall
if one of rear wheels hits an object. When operating in reverse:
A. Operate the wheelchair slowly and at an even speed.
B. Stop often and check to make sure your path is clear of obstacles.



Basic Operation
Before operating your EasyFold PRO 2.0, be sure to read all safety information and precautions
included in this manual. Operate only in the appropriate environment after you have practiced
operating the wheelchair and know how to work the controller.
GET IN
Be certain that the power is OFF with no light on the controller, and make
sure the footrest is down before getting into the wheelchair.
POWER ON
Press the Power button, you will hear a beep and a light will indicate that
power is on.
TURING STEERING
Use the joystick style control to steer and turn left, right or go forward and
backward.
STOPPING
Simply remove your hand from the joystick to stop.
POWER OFF
When stopping, it is advised that you power OFF the wheelchair to prevent
accidents. Press the power button to turn off the wheelchair.
GET OUT
Make sure there is no light on the controller before getting off the
wheelchair.

Reclining In The EasyFold PRO 2.0
The back rest’s angle on the EasyFold PRO is able to be adjusted. To adjust, please follow these
procedures:
STEP 1 - To recline the chair, push the two red clamps together.
STEP 2 -  Push down on the back support to set the position.
STEP 3 - Release the clamps once the position is set.
NOTE: When adjusting the backrest, it is advised to do so while the EasyFold is unoccupied. This
ensures there is no pressure on the backrest while adjusting. Adjusting the backrest with an
occupant could result in the rider falling or tipping the EasyFold.

Charging Batteries
Your EasyFold PRO 2.0 will arrive with fully charged batteries, which should last about 18km under
normal operating conditions. We recommend that you run the EasyFold PRO 2.0 until the batteries
are depleted below the 20% of capacity.
◎ First Charging Method
Charge both batteries at the same time via controller charge port.
1. Turn the power off.
2. Plug in the charger to the controller port (see below).
3. Allow your wheelchair to charge for 6-8 hours or when the light on the charger turns green,
which means your batteries are fully charged.
4. The lights and their meanings are located on the back of the charger.
◎ Second Charging Method:

You have the option of charging the batteries individually.
1. Turn off the main power.
2. Flip open the charger port protector on the front of the battery.
3. Use the secondary charger pigtail to adapt the battery charger to plug into the battery
directly.
◎ More information on the EasyFold PRO 2.0 batteries...
1. The EasyFold Power Wheelchair comes with two charged 24V 7AH lithium batteries.
2. Charged the batteries for 3-4 hours for each battery.
3. Turn the main units’ power off while charging.
4. Do not leave children unsupervised near the power wheelchair while it is charging.
5. Do not attempt to open the battery housing.
6. Red means the power is on and the unit is charging; green means the unit is fully charged.
Note: this information is also located on the back of the charger.
7. When the battery is fully charged, remove cable, then take out the DC charging connector
and AC input power socket.
8. The average time taken to recharge workable batteries will vary from 2 to 8 hours depending
on the level of usage.
9. Do not charge more than 8 hours.
10. If you do not operate the EasyFold PRO 2.0 for two months, we recommend that you charge
the battery for 6-8 hours before use.
11. Overcurrent protection: this system is included on the wheelchair and will shut off the current
from the batteries if triggered, thus shutting the motor down, which will ensure that the motor and
battery do not experience any damage.
12. The life cycle of a lithium battery is measured in charging cycles with an average of 500


charge cycles.
13. Check the battery indicator light daily if you use the EasyFold PRO 2.0 frequently.
14. Do not use any battery chargers that have not been certified by EasyFold Canada.
15. If damaged, do not handle the battery without protective gloves and eyewear.
16. If the battery needs to be disposed of, locate the nearest hazardous materials disposal
facility, and call them for instructions.
17. Before storing your EasyFold PRO 2.0 for long periods of time, take these steps to maintain
the battery:
a. Fully charge the battery before storing.
b. Remove the battery from the wheelchair.
c. Store the battery in a dry, room temperature environment.
d. Avoid temperature extremes and do not allow the battery to freeze.
18. Do not attempt to charge your battery if it is frozen due to extreme weather conditions,
instead first allow it to thaw for several hours.


Free Wheel Mode
In order to push the power wheelchair, it must be put in Free Wheel Mode. This mode disengages
the drive mechanism to the wheels, making them free to push manually. Turn off the power of the
wheelchair when in this mode, both for safety and to save battery power.
1. To put the EasyFold PRO 2.0 in Free Wheel Mode, come to a full stop and turn OFF the
power on the controller.
2. Push down on the two red levers located on each rear wheel as shown: