Easylife EL5606 User manual

Deluxe Folding Guest Bed
INSTRUCTION MANUAL
Model No. EL5606
Please read carefully before use and keep for future reference
Imported and distributed by Easylife Group Ltd, London NW1 0JP
Customer service: 0871 855 6100
For more innovative products from Easylife please visit:
www.easylifegroup.com
IN5606-1 © 2013 Easylife Group Ltd Customer service: 0871 855 6100
For more innovative products from Easylife please visit:
www.easylifegroup.com
PANTONE 072 C
PANTONE 123 C
6. Attach 4 x plastic caps (E) by inserting them into the pre-drilled holes in each outer leg (see Fig D).
7. Attach the head board (I) to the frame of the bed using 2 x bolts (J), align the holes in the head
board with the pre-drilled holes in the frame of the bed and secure in place with 2 x nuts (K) and
tighten with the spanner.
Please note the headboard bolts are a cup square bolt, when securing each nut tighten rmly so
the bolt sits ush with the headboard.
OPERATION
To operate the bed, hold the head board and the opposing handle on the frame and release the two
snap locks. Gently lower one side of the bed to the oor and then repeat for the other side. To close the
bed simply fold both sides and secure in place with the snap locks.
WARNING
• Please do not place hands near hinges when operating the bed
• Please be careful when opening and closing the bed as the side snap locks may
cause potential harm to the user
• The recommended weight load for this bed is 120kgs
TECHNICAL SPECIFICATION
Measurements: Open - L200xW80xH39cm (6ft 7inx2ft 7inx15in).
Folded - L80xW85xH39cm (2ft 7inx2ft 9inx15in).
SINGULAR
QUALITY
IN THE
GUEST
ROOM
Paper weight 60gsm
Fig D
Maximum
user weight
120kg

PANTONE 072 C
PANTONE 123 C
Customer service: 0871 855 6100
For more innovative products from Easylife please visit:
www.easylifegroup.com
Dear Customer
Thank you for purchasing the Luxor Deluxe Folding Bed.
The Luxor is a high-quality, folding metal single guest bed. With a tubular metal frame in
anthracite nish, the bed features an automatic mechanism for extending and folding the legs,
and comes complete with a reex/memory foam mattress in a beige polyester fabric. The frame
has a eucalyptus wood sprung slat base for added comfort, and folds easily, with tted casters
for extra mobility.
PARTS LIST
A 2 x Side Snap Locks
B 2 x Centre Leg Cross Bar
C 4 x Castors
D 1 x Spanner
E 4 x Plastic Caps
F 2 x Leg Retention Bolt
G 4 x Locking Nuts (for castors)
H 2 x Locking Nuts (for leg retention bolt)
I 1 x Headboard
J 2 x Headboard Bolt
K 2 x Nut (for headboard bolt)
ASSEMBLY
1. Carefully remove all packaging.
2. Unfold the bed, remove the xing pack and headboard and rest to one side so as not to lose or
misplace any of the parts enclosed. Please check all the xings are enclosed before
starting assembly.
3. Place the bed on its side and extend the two centre legs fully (Fig A). It is recommended that
you place the bed on a clean, at surface in order to protect the mattress and assemble the bed
more easily.
4. Place 1 x centre leg cross bar (B) over one of the holes in the centre leg. Please note that the
centre leg cross bar must be positioned at against each centre leg (see Fig B). Take
1 x castor (C) and align the screw through the centre leg cross bar and through the pre-drilled
hole in the centre leg. Secure in place with 1 x locking nut (G) and tighten with the spanner (D)
provided. Repeat this process for the other side and other centre leg cross bar.
5. Re-position the bed to its upright position,
release the side snap locks (A) and carefully
lower one side of the bed until the leg
retention bar aligns with the hole in the
corresponding extended outer leg hole (see
Fig C). Once the two holes are aligned secure
in place with 1 x leg retention bolt (F) and
1 x locking nut (H). Tighten with spanner, it
is recommended that you use a screwdriver
to hold in place the bolt when tightening
the locking nut. Repeat this process for leg
retention bar on other side of the bed. This
process will enable the automatic leg action
this bed provides when unfolding it from its
closed position.
Please note the bed must be partially
unfolded for the two holes to align.
Paper weight 60gsm
Fig A
Fig B
Fig C
Centre legs
Leg retention bar