Eaton EX RT EXB 5 User manual

ИБП Eaton / MGE EX RT - Eaton EX RT Батарейный модуль - Быстрый старт
Постоянная ссылка на страницу: https://eaton-power.ru/catalog/eaton-mge-ex-rt/

www.eaton.com
Standard Features
lWhen used with standard system, the
EX RT EXB 5/7/11 provides additional
back-up time.
lHot-swappable.
lRemote Emergency Power Off (REPO)
capability.
Battery Module
EX RT EXB 5/7/11
Quick Start

86-86000-02 B01 - Page 3
STEP 1 EX RT EXB Battery Module Unpacking and Parts Check
EX RT EXB Quick Start
Warranty and
Product Registration
Battery Power Cable
EX RT EXB Battery Module Box Contents
- EX RT EXB 5 Battery Module Part number 86207
- EX RT EXB 7 Battery Module Part number 86207
- EX RT EXB 11 Battery Module Part number 86209
Bezel Hex Drive
Detection Cable
Tower Stand Expanders
(not to scale) Stabilizer Bracket
(4 screws included)
41
Rail Kit
www.eaton.com
EX RT 5/7/11 Systems
Quick Start

86-86000-02 B01 - Page 4
STEP 2 EX RT EXB Tower Configuration
To wer Configuration with Optional Multiple EXB Modules (2 EXBs shown)
Power Module
EXB Battery
Module(s)
(up to 6)
E X 11 R T
To wer Configuration of Standard System
Battery
Module
(up to 6)
EXB RT
EX 1 1 R T
OFF ON
Power Module
Battery Modules
Power Module
Battery Module
Use tower stand expanders provided with each battery module to enlarge the footings.
Power Module
1
1
2
2
4
4
4
4
33
5
1
1
2
2
4
4
4
4
33
5

86-86000-02 B01 - Page 5
STEP 3 Rack Configuration
See System Installation and User Manual for details.
EX RT EXB Front Panel Display and Rack Installation
EX 1 1 R T
OFFON
EX 1 1R T
OFFON
EX11RT
OFFON
EX 1 1 R T
OFF ON
1
2
3
FINISHED PANEL
(rack orientation)
1
2
3
A. Prepare the front panel logo and LCD display for
rack orientation, Apply to all modules including
Transformer, CLA, if equipped (Power Moduler shown).
EXB RT
Layout of Modules in Rack Configuration
(3 EXBs shown)
EX RT Transformer
EX RT Transformer
OFF ON
EX 1
1 RT
B. Rack Installation
3
4
4
4
42
2
1
4
4
5
1
66
6
1. Attach both front mounting ear
brackets to module with supplied
screws (For this step, it is possible to
adjust the position of both front
mounting brackets).
2. Attach rear support brackets to
module.These brackets prevent the
module from sliding out of the rack.
3. Attach rails together, secure with wing
nuts, and finger tighten (both sides).
4. Attach both rails to rear and front of
rack with supplied flathead screws (as
shown).
5. Use caution when sliding unit into
rack.Te mporarily secure unit to rack
with thumb screws on front mounting
brackets.
6. Secure rear support brackets to rails.
6
1. Power Module
(Top, EX RT 5/7/11)
2. EX RT EXB Battery
Module (Upper)
3. EX RT EXB Battery
Module (lower)
4. EX RT EXB Battery
Module (bottom)

86-86000-02 B01 - Page 6
STEP 4 System Connections
1. Check that the battery circuit breaker is in the OFF (“0”) position.
2. & 3. Connect the battery power cable and battery detection cable as shown.
A. System Connections with Battery Modules
Battery Module Circuit Breaker
Battery Power Cable
Battery Detection Cable
1
2
3
1
2
See EX RT 5/7/11 System Installation and User Manual for initial start-up procedures.

86-86000-02 B01 - Page 7

www.eaton.com
86-86000-02 B01