Eaton xComfort CBEU-02/02 User manual

MA-cbeu-02-02.qxd/01.2015k /
136211024
Eaton Industries (Austria) GmbH, A-3943 Schrems
www.eaton.eu/documentation
EU
xComfort CBEU-02/02
1
ca. 60-90% ca. 80-95% ca. 20-60% ca. 0-10% ca. 70-90%
T=+5°C - +40°C
T=-25°C - +70°C
IP20
868,3 MHz
F
R
MRF
Min. Version 3.5
Min. Version 1.09
Red LED
Before to create the RF link
STEP1: Set mode (1..4) on CBEU
STEP2: Set actuator to teach-in mode
STEP3: Close contact (look at details on page 3)
STEP4: Set actuator to normal operation mode

2
5 mm
1,5 mm2
1
2
3a
3b
4
!
3V-CR2477N
,
4b
5
6

3
tested by:
TÜV Austria Services GmbH, Notified Body
1230 Vienna, Deutschstrasse 10, Austria
Affixing date of CE mark:
2003
Doc.Id.:
CBEU-02/02
Heinz Ursprunger Friedrich Schröder
Director Product Line
Director Quality
& Marketing Management & EHS
Declaration of Conformity
We, EATON Industries (Austria) GmbH
3943 Schrems, Eugenia 1
Austria
declare that product (family)
Eaton - Binary input with battery power supply,
CBEU-02/02
(the declaration of conformity applies to all
listed types within our actual product catalog)
provided that it is installed, maintained and used in the
application intended for, with respect to the relevant manufacturers
instructions, installation standards and “good engineering practices”
complies with the provisions of Council directive(s):
EMC Directive 2004/108/EC
Radio and Telecommunications Terminal Equipment 99/05/EC
RoHS Directive 2011/65/EU
based on compliance with European standard(s):
EN301489-3 V1.6.1, EN300220-2 V2.4.1, EN50491-5-1/10, EN50491-5-
2/10, EN60950-1/06 + A11/09 + A1/10 + A12/11 + A2/13, EN62479/10
01.12.2014

4
Configuration of CBEU
Symbols:
LED is on LED flashes 5 times LED is on Lamp (LED) is on Lamp (LED) is on
1. Make connection
ASSIGN SWITCH MODE (MODE 2)
1. Press the config button on CBEU (230 V version
requires screwdriver) to select switch mode (Mode 2),
LED flashes 2x
2. Open contact of the binary input
3. Press the config button on actuator with a screwdriver
shorter than 0,5 sec =>actuator enters teach-in mode,
the LED in the actuator is on
4. Close contact of the binary input
5. The LED in the actuator flashes 2x for confirmation
6. Press the config button on actuator shorter than 0,5
sec => actuator leaves teach-in mode
ASSIGN PUSH BUTTON MODE (MODE 1)
1. Press the config button on CBEU (230V version
requires a screwdriver) to select push button mode
(mode 1), LED flashes 1x
2. Press the config button on actuator with a screwdriver
shorter than 0,5 sec => actuator enters teach-in
mode, the LED in the actuator is on
3. Press pushbutton on the contacts of the binary input
shorter than 0,5 sec
4. The LED in the actuator flashes 2x for confirmation
5. Press the config button on actuator shorter than 0,5
sec => actuator leaves teach-in mode
2. Delete connection selectively
DELETE SWITCH MODE (MODE2)
1. Press the config button on actuator with screwdriver
shorter than 0,5 => actuator enters teach-in mode,
the LED in the actuator is on
2. Open contact of the CBEU
3. Wait until the LED in the actuator has flashed 5 x
4. Press the config button on actuator shorter than 0,5
sec => actuator leaves teach-in mode
DELETE PUSH BUTTON MODE (MODE2)
1. Press the config button on actuator with a screwdriver
shorter than 0,5 => actuator enters teach-in mode,
the LED in the actuator is on
2. Press pushbutton on the contact of the binary input
until LED has flashed 5 x
3. Press the config button with a screwdriver shorter
than 0,5 sec => actuator leaves teach-in mode
3. Reset actuator
1. Press the config button with a screwdriver shorter than 0,5 sec =>
actuator enters teach-in mode, the LED in the actuator is on
2. Press the config button with a screwdriver until LED has flashed 5 x
3. The actuator leaves teach-in mode automatically after some seconds