Eaton UM11-RP Assembly instructions

Installation sheet
Please read the following safety instructions carefully
and follow the installation steps in sequence.
UM11-RP Universal Roll-out Shelf
UT11-RP Transition Roll-out Shelf
UM75-RP Drop File Roll-out Shelf
UM14-RP 12" Bin Drawer
UM20-RP 15" Bin Drawer
UO47-FP Center Rails for Front-to-back Filing
PLEASE NOTE:
1. Some le drawer accessories may not be used in
combination with one another.
2. Some of the following instructional information
may not pertain to all of the above listed products.
SIDE EXTENDERS
15" Bin Drawers (item number UM20-RP) require
side extenders to increase the ling height of the
drawer sides. To assemble the extensions, position
them as shown in gure 1 and secure each side with
three #10 phillips head self tapping screws. (The
screws must be assembled from inside the drawer.)
BIN DRAWER FRONT
12" and 15" Bin Drawers (item numbers UM14-
RP and UM20-RP) require a solid front panel. To
assemble the panel rst hook the panel’s bottom
ange under the drawer handle and then pivot the
panel to a vertical position. Secure the panel by
installing either two or three (depending on the
drawer size) #8 phillips head self Universal roll-out
tapping screws into each side. See gure 2.
Modular bin drawers
Extender
15" Bin drawer
#10 Phillips head
self tapping screws
Figure 1
Figure 2
Universal
roll-out
Front panel
Bottom ange
Roll-out handle
#8 Phillips head
self tapping screws

LATERAL FILE BARS (UM14-FP and UM20-FP Bin
Drawers require only one lateral le bar at the back of
the drawer. The lip of the Bin Drawer front will serve as
the front le bar.)
Determine the location of the Lateral File Bar(s) using
gure 3 as a guide. The long vertical slots may be used
for standard height media (low bar position). The shorter
slots are for extra tall media (high bar position). (PLEASE
NOTE: the high bar position MUST be used for the
AM14-FP and AM20-FP Bin Drawers.)
Install the Lateral File Bars with the stiffening anges
AWAY from the media. While holding the bar above the
drawer, insert one end into the desired slot. Lower the
opposite end of the bar and insert it into the desired slot.
Tap the bar down to seat it onto the bottom of the slots.
See gure 4.
Lateral le
bar
Slot Slot
Slot
Roll-out
side
Roll-out
side
Push down
to seat
Roll-out
side
Lateral le
bar
Insert opposite
end
Lower to
level position
Insert
Lateral le
bar
Figure 4
Legal folder
U.S. letter folder (alternate position)
DIN A-4 folder
U.S. letter (8-1/2") folder
Low bar position
Figure 3
High bar position

Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
© 2018 Eaton
All Rights Reserved
Printed in USA
Publication No. IL210020EN
April 2018
Eaton is a registered trademark.
All trademarks are property
of their respective owners.
CENTER RAILS FOR FRONT-TO-BACK FILING
The Center Rails hang on the two lateral le bars (or
in the case of a Bin Drawer, on the rear le bar and
the ling lip on the Bin Drawer Front). When hung on
two Lateral File Bars, the Center Rails are innitely
adjustable. When the Center Rails are used in a
AM14-FP or AM20-FP Bin Drawer, slots in the bin
drawer front determine various ling options. See
gure 5.
TO INSTALL DRAWER INTO A CABINET
Refer to instruction sheet #66718 to install the
assembled drawer into a cabinet.
Lateral le bar
(rear position)
Center rail
Print-out (14-7/8") folder
Figure 5
DIN A-4 folder DIN A-4 folder
Letter (8-1/2" x 11") folderLetter (8-1/2" x 11") folder
Replacement parts lists
Part no. Description
1 2642P Weldment, universal roll-out
21184P Front, bin drawer-15"
1185P Front, bin drawer-12"
3 1179X Back panel
4 81902 Hanger rail
5 66095 Support, center
6 81933 Extender, R.H.
7 81932 Extender, L.H.
8 54055 #10 Phillips head self tapping screw
9 68374 #8 Phillips head self tapping screw
10 27157 Suspension
11 81761 Bracket, interlock cam
12 81751 Interlock cam