START-S19K RED
-2-
SYMBOL
The special messages indicated below, may appear throughout the
technical manual to draw attention to information that clari es or
simpli es a procedure.
The addition of this graphic symbol to a “Danger” or
“Warning” safety advice, indicates that there is an electri-
cal or mechanical risk, which can cause physical injury if
the instructions are not followed. Please follow all safety
messages that have this symbol to avoid injury or material
damage.
Damage! For safety reasons, protect your face during the
connection.
WARNING
Installation, management, service and maintenance must only be
carried out by quali ed personnel. The producer assumes no re-
sponsibility for the consequences that may arise from the use of this
material. Failure to followthese instructions can result in serious
personal injury.
INTRODUCTION
This manual provides all the information necessary for the correct
installatin and use of the equipment in your possession. It must be
read carefully at the time of purchase, and consulted to chack the
limitations on the use, and when you are about to carry out mainte-
nance. The manufacturer reserves the right to make any changes to
the product without notice.
SAFETY MEASURE
In the event of incorrect use, repairs or modi cations made by un-
quali ed personelle, all guarantees will be void. The manufacturer
declines all responsibility for damage deriving from inappropriate
use of the product or from use other than that for which the product
was intended. The manufacturer declines all responsibility for con-
sequential damages except for the civil liability for the products. We
remind you that automatic gate and door systems must only be in-
stalled by quali ed technical personnel, in full compliance with the
law. Before each installation check the mechanical strength of the
gate or door. Check that all mechanical stops are suitable to stop the
gate/door to avoid of damage.
MEASURE FOR THE ENVIRONMENT
In the event of incorrect use, repairs or modi cations
made by unquali ed personelle, all guarantees will be
void. The manufacturer declines all responsibility for da-
mage deriving from inappropriate use of the product or
from use other than that for which the product was inten-
ded. The manufacturer declines all responsibility for consequential
damages except for the civil liability for the products. We remind you
that automatic gate and door systems must only be installed by qua-
li ed technical personnel, in full compliance with the law. Before
each installation check the mechanical strength of the gate or door.
Check that all mechanical stops are suitable to stop the gate/door to
avoid of damage.
INDEX
1. INTRODUCTION 3
1.1 SAFETY PRECAUTIONS 3
1.2 FIELD OF APPLICATION 3
1.3 TYPE OF INSTALLATION 3
1.4 TECHNICAL FEATURES 3
2. INSTALLATION 4
2.1 DIAGRAM OF THE CONTROL UNIT AND ELECTRICAL CONNECTIONS 4
2.2 CONNECTION OF THE POWER SUPPLY 5
2.3 CONNECTION OF THE MOTOR 5
2.1 CONNECTION OF A 230 VAC SIGNAL LIGHT 5
2.4 PRE-LIGHTING 5
2.5 CONNECTION OF A 24V LIGHT FOR OPEN OR MOVING GATE 6
2.6 CONNECTION OF THE LSC AND LSC 6
2.7 POWER SUPPLY FOR ACCESSORIES 6
2.8 CONNECTION OF STOP DEVICES 7
2.9 CONNECTION OF THE START COMMAND 7
2.10 CONNECTION OF A PARTIAL OPENING 7
2.11 CONNECTION OF THE ANTENNA 7
2.12 CONNECTION OF THE PHOTOCELLS (ONLY CLOSE) 24 VAC 8
2.13 CONNECTION OF THE SECURITY OR ANTI-FOLD UP 9
2.14 OPENING / CLOSING IN CASE OF EMERGENCY 9
3. USE AND FUNCTIONS OF THE CONTROL PANEL 10
3.1 SETTINGS AND PARAMETERS 10
3.2 EXAMPLE HOW TO USE THE MENU AND INFORMATION 11
3.3 SET UP A PASSWORD FOR PROGRAMMING 12
4. ACTIVATE THE SINGLE OUTPUTS 13
5. FUNCTIONS AND ADJUSTMENT 15
5.1 LOGIC OF FUNCTIONS 15
5.2 FUNCTIONS AND ADJUSTMENT 16
5.3 SET UP OF SPEED AND ACCELERATION 17
5.4 CONNECTION OF RX RADIO BAND (AVAILABLE ON REQUEST) 17
5.6 MEMORIZATION OF THE ENCODER KOSTAL 18
6. RESTORE OF FACTORY DEFAULT SETTINGS 19
6.1 RESTORE FACTORY SETTINGS 19
6.1 SAVE AND CHECK OF THE PARAMETERS 20
7. TROUBLESHOOTING 20
8. INSTALLATION 21
8.1 GROUP S 21
8.2 GROUP R 22
8.3 GROUP T 23
8.4 GROUP L 23
9. DECLARATION OF CE CONFORMITY 24
