EBIKELING S830 User manual

LCD S830 User Manual

1. Exterior Parameters
Casing Material: ABS
Display Material: High Hardness Acrylic (the
same hardness value as tempered glass).
2. Operating Voltage and Connections
a. Operating Voltage: DC24V/36V/48V/52V/72V (set by the control panel).
b. Connections: Julet Waterproof Connector.
Converter Ring φ22.2mm
Single Supporter

3. Functions
a. Display
Speed Display, Motor Power Ratio Display, Battery Level Display,
Error Indication, Total Mileage, Single Mileage, Single Running Time
Light Signal
b. Control and Settings
Power Switch, 6km/h Inching Control, Wheel Diameter Setting, Top Speed
Setting, Time Setting for Auto-Hibernation, Backlight Brightness Setting,
Voltage Level Setting
c. Communications Protocol: UART
Display Readings (display at the start for 1 second)
3.1 Light
3.2 Battery Level
(optional function)

6km/h Walk Boost Real-Time Cruise
Low Battery
Controller Failure
Throttle Failure
Powered Ride
Brake
Motor Failure
3.3 Multi-Functions Display
Total Mileage : ODO
Single Mileage : TRIP
Single Running Time : Time
Current Voltage : VOL
Operating Current : CUR
3.4 Vehicle Power PAS Level
3/5/9 gear modes available.
It is five (5) gears by default.
3.5 Speed Display
Maximum Speed : MAX
Average Speed : AVG
Measuring Unit : MPH or KM/H
The panel will calculate the actual traveling speed based on the wheel diameter
and signal data (number of magnet steel is needed for Hall motors).
3.6 Vehicle Status

3.7 Parameters
To go to Parameters, press & hold “UP & DOWN ARROW” at the same time for
about 5 seconds, within the 8 seconds when you turn the kit on.
P01 : Brightness (1 is the darkest; 3 is the brightest)
P02 : 0 is KM, 1 is MILE
P03 : Voltage grades; 24V/36V/48V/52V/72V
P04 : Sleep time. 0 means the LCD screen will never go off for energy save
mode, other numbers stand for the sleep time (1-60 min).
P05 : PAS grades.
3: 3 level speed for both throttle and PAS
5: 5 level speed for both throttle and PAS
9: 9 level speed for both throttle and PAS
P06: Wheel Size. Unit: inch Precision: 0.1
The wheel size unit shown in inches, must be set correctly.
P07: Range: 1-100
This is 46 for direct drive (1200w and above) motors and 01 for geared (500w -
750W) motors.
P08: Speed Limit
Range: 0-50 km/h, 100 means no limit
The limit is set in Km and can not be switched to a Mil. So calculate it carefully
when you set the limit.
Communication Status (controlled by the controller): The driving speed keeps the
same as the ones we set. Random error: ±1km/h. (Speed limit is for both PAS and
Throttle)
Note: These data are based on KM. When changing KM to Mile, the speed value
on the screen would convert to correct Miles automatically, but if you do not
change the setting of the speed limit from KM to Mile, it would be different from
the real speed limit in Mile.

P09: Zero & Non-zero Start Setting:
Zero start (0) will engage the motor instantly while Non-zero start (1) will
give some delay when you throttle.
P10: Drive Mode Setting
0: Power Drive – The specific gear of the assist drive decides the assist power
value. In this status, the throttle does not work.
1: Electric Drive – The vehicle is driven by the handlebar. In this status the power
gear does not work.
2: Power Drive + Electric Drive – Electric drive does not work in zero-start status.
P12: Assist Power Intensity Range: 0-5
Lower value provides a little assist when you start pedaling.
P13: Power Magnet Steel Number.
There are 3 types: 5, 8, and 12. Dots on the magnetic ring. In our system, it is 12
by default.
P14: The Current-limiting of Controller
The original Current is 12A. Range:1-20A
Please check the current your controller and the hub motor can handle. Set the
limit accordingly.
PS: The latest versions of the SW900 and S830 display adjust the current
automatically.
P16: ODO Zero-Out: Long press the upper key for 5 seconds and ODO will zero
out. Use this option to reset ODO.
Note: When you set P09 as 0, whether you set P10 as 0, 1, or 2, both throttle
and PAS can start the system and work.
When you set P09 as 1 and P10 as 0, only PAS can start the system.
When you set P09 as 1 and P10 as 1, both throttle and PAS won’t work.
When you set P09 as 1 and P10 as 2, only PAS can start the system, then the
throttle will work.

Introduction of Keys
Key operations involve short press, long press, and long press of combination keys.
Short press is used for short/frequent operations as:
1. Short press the Up or Down Button to change assist
power/speed during riding.
2. Short press the “M” button to switch the readings in the multi-function
display section.
Long press on a single key is used to switch mode/on/off status.
Long press on combination keys to set parameters, which can avoid misoperations
(short press on combination keys is disabled, for it’s easy to induce misoperation and
hard to manipulate).
Detailed Instructions
1. Changing the assist power.
a. Short press assist power +1.
b. Short press assist power -1.
4. Keys
Arrangement of keys on the panel:

2. Switch Speed Display
Long press + to switch speed display type.
3. Enable / Disable 6km/h cruise, set the real-time cruise, and turn on/off the lights.
When the vehicle is parked, long press to enter 6km/h cruise mode.
When the vehicle is traveling, long press to enter real-time cruise mode.
Long press or engage the Throttle to exit the cruise mode.
Long press to turn on/off backlight.
4. Turn on/off the LCD Display
When the display panel is operating, long press and it will be turned off,
otherwise, it will be turned on.
5. Switch Displayed Readings in Multi-Functions Section
Short press to switch readings shown in the multi-function section.
6. Set Parameters
Long press + to enter the setting interface.
In the setting interface, short press or to change the
value to the parameter, which will blink after modification. After selecting the
parameter that needs to be set,

I. Short press to switch to the next parameter and the previously set value
will be saved at the same time.
II. Press + to exit the setting and save the parameters.
Without this operation, the system will automatically exit and save the modified
parameters after 10 seconds.
Note: Due to product upgrade, the product you purchased may be slightly different
from the descriptions in this user manual, this will not affect normal usage.