Ebode RMV User manual

RMV
Receiver
Wall-Mounted Shutter Module

Receiver - Wall-Mounted Shutter Module Ref : RMV
July 2009 page 2 RMV
General Security Note
For carefree and safe use of this product, please read this manual and safety information
carefully and follow the instructions. Technical manipulation of the product or any changes
to the product are forbidden, due to security and approval issues.
Please take care to set up the device correctly - consult your user guide. WARNING: Do Not
Open! Risk of Electrical Shock. Voltages in this equipment are hazardous to life. No user-
serviceable parts inside. Refer all servicing to qualied service personnel.
Important: the product must be used according the instructions in this manual and is not
suitable for other purposes.
Please avoid the following: strong mechanical wear and tear, high temperature, strong
vibrations, and high humidity.
Please also respect the additional security notes in the various user guide chapters. To
ensure correct set up please read the manual and security notes carefully.

Receiver - Wall-Mounted Shutter Module Ref : RMV
July 2009 page 3 RMV
Schematic 1
To connect the in-wall switch.
CONNECTING BLOCK
To learn one address on wall switch (unique
addressable control)
An address is made of a HOUSE code and UNIT code, please refer
to the manual of the transmitter to properly x the code to learn
by the receiver.
The following procedure consists of learning one (or even more
than one) address from the transmitter into the receiver RMV.
Please bear in mind to shut off general mains in the electrical panel.
Connect all wires as indicated (refer to wiring
diagram 1)
L : stands for input Live 230V - 50 Hz
N: stands for input Neutral 230V - 50Hz
How to connect Live + Neutral Input
N : Neutral
Wiring up Live +
Neutral outputs
LIVE DOWN output to
Motorization
C : Never connect C : only for low voltage
How to install wall mount switch.
Wall insert box : dia. 65mm, 40mm deep
1.Gently take off paddle from wall switch.
2.Wire up Wall Switch within wall insert box, then x receiver
along with provided screws again wall insert box.
Please note that the general mains in the electrical panel
should be turned on again before you start programming.
Ph N
LIVE UP output to
Motorization

Receiver - Wall-Mounted Shutter Module Ref : RMV
July 2009 page 4 RMV
1. Take off the paddle of the receiver.
2. Press and hold the PROG key till LED lights up green (after 3
seconds).
3. Release PROG key.
4.Press/release minimum 10 times the key PROG, the LED starts
blinking for 5 times then to blink off. You are now in secured mode.
5. Just put on again the paddle (make sure ebode logo is located on
the bottom right side).
To switch from standard to secure
communication protocol.
The secured ebode protocol can be enabled when needed. When
enabled ONLY ebode transmitters like the TPC, EM and IMRF can be
used to control ebode modules like RMA, RMV and RPT.
The ebode communication protocol can be associated with the
professional security communication protocols, mostly used in alarm
systems.
FYI :
- Once powered on, the RMV receiver is in the mode to acknowledge X10
standard controls (To secure communication beteween transmitter and receiver
pls refer to step 4).
- The RMV receiver responds to any RF command received from any transmitter,
and translates this to X10 commands on the power line.
UP
DOWN
1. Take off the paddle of the receiver.
2. Shortly press the PROG key, a green LED blinks quickly showing
the receiver is awaiting an order from any transmitter (can be either
RF or PLC mode).
3. Choose and press the chosen key of a remote or transmitter (RF
remote, PLC command / programmer) to automatically learn the
address. Green LED turns off to acknowledge the order.
4. The unique address is now conrmed.
5. In case of you would like to learn more than one command (RF
remote, PLC command / programmer) just proceed same way from
step 2 up to 4.
6. Once learning is complete, just put the paddle back onto the
receiver. NOTE : For proper installation, make sure the ebode logo
shown on the paddle is positioned on the bottom right side.
1.Gently take off paddle from wall switch.
2.Wire up Wall Switch within wall insert box, then x receiver
along with provided screws again wall insert box.

Receiver - Wall-Mounted Shutter Module Ref : RMV
July 2009 page 5 RMV
1. Take off the paddle from the receiver.
2. Press and hold the PROG key till LED lights up green (after 3
seconds).
3. Release PROG key. Both green and red LEDS blinks quickly on, to
turn off after several seconds (LED to blink orange). Time to erase
depends on the number of entered valid addresses.
4. All addresses are now erased, receiver goes back in X10 standard
communication protocol.
5. Put on again the paddle (make sure ebode logo is located on the
bottom right side).
Operating the RMV receiver
Gently press the upper key (ON) to go up.
Gently press the lower key (OFF) to go down.
Use a X10 compatible remote control, RF wall switch or programmer to
check remote control of the shutter, roll blind or motorized screen.
Troubleshooting: please check FAQ and technical support on
www.ebodeelectronics.eu.
To erase all recorded adresses on the receiver (overall RESET).
This procedure consists of erasing all addresses you may entered
over time which are not valid to control your Home Automation
system.
RMV cannot be controlled anymore from either an RF or PLC remote/
programmer?
- Check and/or change the battery of your remote.
- Go for an overall RESET of the receiver as it may have lost the address due to
too many manipulations (starts from point 5), then re-initialize transmitter and
receiver RMV both together (starts from point 3).
Red or Green LED blinks randomly even if no commands are given:
RF or PLC interference may occur (ie Fluo lamps, Reversible A/C, PC monitor)
please add either a lter FD10 in the main control panel or a plug in module FM10
to lter the product in cause.

Receiver - Wall-Mounted Shutter Module Ref : RMV
July 2009 page 6 RMV
CE DECLARATION OF CONFORMITY
We, BMB Electronics BV, Kortakker 10 – 4264 AE Veen – The Netherlands, herewith
declare that the following designated product RMV, is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Product category : general consumer (category 3).
Date: March 2009 Peter Schoon - Product Manager BMB
Device: The use of the symbol indicates that this product may not be treated as household
waste. By ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could otherwise be
caused by inappropriate waste handling of this product. For more detailed information about
recycling of this product, please contact your local city ofce, your household waste disposal
service or the shop where you purchased the product.
Batteries: Do not dispose of used batteries in the household rubbish!
They should be deposited at a collection point for used batteries.
Device:
The use of the symbol indicates that this product may not be treated as household waste. By ensuring this
product is disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste handling of
this product. For more detailed information about recycling of this product, please contact your local city
office, your household waste disposal service
or the shop where you purchased the product.
Batteries
Do not dispose of used batteries in the household rubbish! They should be deposited at a collection point for used batteries.
Device:
The use of the symbol indicates that this product may not be treated as household waste. By ensuring this
product is disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste handling of
this product. For more detailed information about recycling of this product, please contact your local city
office, your household waste disposal service or the shop where you purchased the product.
Batteries
Do not dispose of used batteries in the household rubbish! They should be deposited at a collection point for used batteries.

Receiver - Wall-Mounted Shutter Module Ref : RMV
July 2009 page 7 RMV
Also available from ebode electronics:
On-Wall Modules
In-Wall Modules
Under development
Product Description
EM 2-position RF wall switch, ideal for retro t installations to e.g.
control blinds, shutter, home cinema screens but also lighting
or appliances.
IMRF Single position RF wall switch, ideal for retro t installations to
e.g. control applications or an inside or outside light.
RMV Control your shutter, blind or e.g. cinema screen via the front
panel keys, or remotely via any ebode / X10 compatible con-
troller.
RMA Control your appliance, light or e.g. pump via the front panel
keys, or remotely via any ebode / X10 compatible controller.
RPA, RPL,
RPT Ideal for retro t installations, the classic X10 plugin module in a new and stylish jacket. Control your appliance or lamps etc,
via any ebode or X10 compatible controller via PLC AND RF!
TPC/ TMML New stylish RF remote to control any ebode or X10 compatible
RF receiver.
Product Description
EMML 2-position RF in-wall module to install behind any mechanical
wall switch. The EMML is battery operated.
RMML In-wall RF receiver, ideal for any switches lights and appliances
up to 300W.
PMML A package containing both the EMML and the RMML.
Product Description
RMP Update on existing RMV with dry contact output. Ideal to
control e.g a motorized gate.
RMSN In-wall RF receiver without Neutral for light applications
including incandescent, halogen, uorescent, LED (even 0.5W
charge).

www.ebodeelectronics.eu