Echo PPT-260 - 02-07 1 User manual

POWER PRUNERTM
OPERATOR'SMANUAL 1
Power PrunerTM
Operator'sManual
MODEL: PPT-260
X770001031
02/07
X7702090901
WARNING
Readrulesforsafeoperationandinstructionscarefully. ECHOprovidesanOperator's
ManualandaSafetyManual. Bothmustbereadandunderstoodforproperandsafe
operation.

2
Copyright© 2007 By Echo, Incorporated
All Rights Reserved.
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job
dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will
find both easy to use and full of helpful operating tips and SAFETY messages.
THE OPERATOR'SMANUAL
Read and understand this manual before operation. Keep it in
a safe place for future refenence. It contains specifications
and information for operation, starting, stopping, mainte-
nance, storage, and assembly specific to this product.
THE SAFETY MANUAL
Read and understand this manual before operation. Keep it in
a safe place for future refenence. It explains possible hazards
involved with the use of Power PrunerTM and what measures
you should take to make their use safer.
TABLE OF CONTENTS
Introduction ...............................................................2
- The Operator's Manual........................................2
- The Safety Manual .............................................2
Safety .........................................................................3
- Manual Safety Symbols and Important
Information .........................................................3
- InternationalSymbols .........................................3
- Personal Condition and Safety Equipment .........4
- Kickback .............................................................6
- Equipment ...........................................................7
EmissionControl........................................................7
Description ................................................................8
Contents .................................................................. 10
Assembly ................................................................. 10
- DriveShaft/PowerHead ................................... 10
- Cutting Attachment to Drive Shaft Installation 11
- Throttle Linkage and Ignition Leads................. 12
- Saw Chain Tension Adjustment ....................... 12
Operation ................................................................. 13
- Fuel ................................................................... 13
- Lubricating theGuide Barand SawChain ........ 15
- Adjusting AutomaticOiler................................ 15
- StartingColdEngine ......................................... 16
- StartingWarmEngine....................................... 17
- Stopping Engine ............................................... 17
- Pruning Techniques ......................................... 18
Maintenance ............................................................ 19
- SkillLevels ........................................................ 19
- Maintenance Intervals ...................................... 19
- AirFilter............................................................ 20
- FuelFilter .......................................................... 20
- SparkPlug ......................................................... 21
- CoolingSystemCleaning.................................. 21
- ExhaustSystem ................................................. 22
- Carburetor Adjustment ..................................... 23
- GuideBarandSawChainReplacement ............ 25
- FilingSawChain ............................................... 27
Troubleshooting ...................................................... 28
Storage..................................................................... 29
Specifications........................................................... 30
ServicingInformation............................................... 32
- Parts.................................................................. 32
- Service .............................................................. 32
- ECHOConsumer ProductSupport.................... 32
- Warranty Card .................................................. 32
- Additional or Replacement Manuals ................ 32
Specifications,descriptionsandillustrative material in
this literature are as accurate as known at the time of
publication, but are subject to change without notice.
Illustrations may include optional equipment and
accessories, and may not include all standard
equipment.

POWER PRUNERTM
OPERATOR'SMANUAL 3
SAFETY
MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION
WARNING
Thesafetyalertsymbolaccompaniedbytheword
“WARNING”callsattentiontoanactorcondition
whichCANleadtoseriouspersonalinjuryordeath
ifnotavoided.
CIRCLEANDSLASHSYMBOL
This symbol means the specific action
shown is prohibited. Ignoring these
prohibitions can result in serious or fatal
injury.
CAUTION
Thesafetyalertsymbolaccompaniedbytheword
“CAUTION”callsattentiontoanactorcondition
whichmayleadtominorormoderatepersonalinjury
ifnotavoided.
NOTE
This enclosed message provides tips for use, care
and maintenance of the unit.
IMPORTANT
The enclosed message provides information
necessary for the protection of the unit.
DANGER
Thesafetyalertsymbolaccompaniedbytheword
“DANGER”callsattentiontoanactorcondition
whichWILLleadtoseriouspersonalinjuryordeath
ifnotavoided.
Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages
preceded by symbols or key words. The following is an explanation of those symbols and key words and what they
mean to you.
Hot
Surface
Symbol
description/application Symbol form/shape Symbol
description/application
Symbol form/shape
Read and understand
Operator's Manual.
Wear eyes, ears and
head protection
Fuel and oil mixture
Finger Severing
Safety/Alert
Avoid all power
lines. This unit is not
insulated against
electrical current.
Do not operate clos-
er than 15 M (50 ft.)
from electrical
hazards.
Keep bystanders at
least 15 meters
(50 feet) away.
Plan retreat path
from falling
objects.
Wear hand
protection. Use
two handed.
DO NOT smoke
near fuel.
INTERNATIONALSYMBOLS
Symbol
description/application Symbol form/shape Symbol
description/application
Symbol form/shape
Carburetor adjustment
- Idle speed
Carburetor adjustment
- High speed mixture
Emergency stop
Carburetor adjustment
- Low speed mixture
DO NOT allow
flames or sparks
near fuel.
Wear slip resistant
foot wear.
Ignition
ON/OFF
Chain lubrication Primer bulb
Choke Control
"Cold Start"
Position
(ChokeClosed)
Choke Control
"Run"
Position
(ChokeOpen)

4
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
•ifyouaretakingmedication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
Wear eye protection that meets ANSI Z87.1 or CE
requirements whenever you operate the unit
Face and Head Protection
When trimming overhead, always wear head protection
meetingANSIZ89.1orCErequirementswithafullface
shield. Head protection with full face shield will help
protect you from falling branches and debris.
Hand Protection
Wear no-slip, heavy duty work gloves to improve your
grip on the unit handles. Gloves also reduce the transmis-
sion of machine vibration to your hands.
Vibration and Cold
It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals may be
brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sensa-
tions followed by loss of color and numbness in the fingers. The following precautions are strongly recommended
becausetheminimumexposurewhichmighttriggertheailmentis unknown.
• Keep your body warm, especially the head, neck, feet, ankles, hands
and wrists.
• Maintain good blood circulation by performing vigorous arm
exercises during frequent work breaks and also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where
operating the unit or other hand-held power equipment is not
required.
• If you experience discomfort, redness, and swelling of the fingers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
PERSONAL CONDITION ANDSAFETY EQUIPMENT
WARNING
Power PrunerTM users risk injury to themselves and others if the Power PrunerTM is used improperly and or safety
precautions are not followed. Proper clothing and safety gear must be worn when operating a Power PrunerTM.
Hearing Protection
ECHOrecommendswearinghearingprotectionwhenever
unit is used.
Proper Clothing
Wear snug fitting, durable protective clothing; chain saw
safety pants or chaps are recommended.
• Pants should have long legs, shirts with long sleeves.
• DONOTWEARSHORTS,
• DONOTWEARTIES,SCARVES,JEWELRY.
Wear sturdy protective safety shoes or boots with non-
skid soles;
• DONOTWEAROPENTOEDSHOES,
• DONOTOPERATEUNITBAREFOOTED.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue,
which may lead to heat stroke. Schedule heavy work for
early morning or late afternoon hours when temperatures
arecooler.

POWER PRUNERTM
OPERATOR'SMANUAL 5
DANGER
All over head electrical conductors and communications wires can
have electricity flow with high voltages. This unit is not insulated
against electrical current. Never touch wires directly or indirectly
when pruning, otherwise serious injury or death may result.
WARNING
Do not operate this product indoors or in inadequately ventilated
areas. Engine exhaust contains poisonous emissions and can cause
serious injury or death.
ReadtheManuals
• Provide all operators of this equipment with the Operator's Manual,
and instructions for safe operation.
CleartheWorkArea
• Spectators and fellow workers must be warned, and children and
animalspreventedfrom coming nearerthan15m (50 ft.)whiletheunit
is in use.
UseProperClothing&Equipment
• Always wear head protection with full face shield to help protect
against falling branches and debris.
KeepAFirmGrip
• Grip Power PrunerTM with both hands with thumbs and fingers
encircling the handle, and shaft tube.
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness,
swelling, numbness, weakness and extreme pain in those areas. Certain repetitive hand activities may put you at a high
riskfor developingaRepetitive StressInjury(RSI).Anextreme RSIconditionis CarpalTunnelSyndrome(CTS),which
could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged
exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended or twisted position.
Instead try to maintain a straight wrist position. Also, when grasping,
use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive move-
ment.
• Do exercises to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if
you feel tingling, numbness or pain in the fingers, hands, wrists or
arms. The sooner RSI/CTS is diagnosed, the more likely permanent
nerve and muscle damage can be prevented.

6
KeepASolidStance
• Maintain footing and balance at all times. Do not stand on slippery,
uneven or unstable surfaces. Do not work in odd positions or on
ladders. Do not overreach.
• Operate the Power PrunerTM only from the ground or out of an
approved bucket lift.
• Always evaluate the branches to be pruned for hazards such as
loose dead branches which may fall and strike the operator or
helpers. Remove hazards before pruning.
• Plan retreat path from falling objects.
• Cut branches bounce when striking ground.
• Check that shoulder harness is adjusted for safe, comfortable
operation. See picture at right for proper adjustment.
• Turn the Power PrunerTM off when moving from tree to tree.
• Avoid any contact with saw chain.
AvoidHotSurfaces
• Keep exhaust area clear of flammable debris. Avoid contact during
andimmediatelyafteroperation.
KICKBACK
Kickback may occur when the moving saw chain at the nose or tip of
the guide bar touches an object, or when the wood closes in and
pinches the saw chain in the cut. In some cases this may cause a
lightning-fast reverse action, kicking the guide bar and saw chain up
and back or down and back towards the operator. Either of these
reactions may cause the operator to lose control of the Power PrunerTM
which could result in serious personal injury.
With a basic understanding of kickback, you can reduce or eliminate the
element of surprise which contributes to accidents.
Avoid contact of the guide bar tip with any object while the saw chain
ismoving.
Cut only wood. Avoid striking concrete, metal, wire, or other obstruc-
tions which could cause kickback or damage to the saw chain.
If the saw chain does strike a foreign object, immediately stop the
engine, inspect and repair the Power PrunerTM if necessary.
WARNING
Kickback can lead to dangerous loss of control of the Power PrunerTM and result in serious injury to the operator or
any one standing close by. Hold the Power PrunerTM firmly with both hands with thumbs and fingers encircling the
front and rear handles. Be aware of the down and outward path the pruner will take after the cut is made.

POWER PRUNERTM
OPERATOR'SMANUAL 7
EQUIPMENT
WARNING
Serious injury may result from the use of non approved guide bar and saw chain combinations. ECHO, INC. will not
be responsible for the failure of cutting devices or accessories which have not been tested and approved by ECHO
for use with this unit. Read and comply with all safety instructions listed in this manual.
• Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed.
• Inspect fuel lines, tank, and area around carburetor for fuel leaks. DO NOT operate unit if leaks are found.
Guide Bar and Saw Chain
• Check that the cutting attachment, guide bar, and saw chain is firmly attached and in safe operating condition.
• Use only one Echo-approved extension on the pruner.
• Do not hit rocks, stones, tree stumps, and other foreign objects with the saw chain.
• Do not cut into the ground with the saw chain.
• If cutting attachment end strikes an obstruction, stop engine immediately and inspect saw chain for damage.
• Do not operate with a dull, fractured, or discolored saw chain.
• Removeallforeignobjectsfromworkarea.
• Always cover the guide bar and saw chain with guide bar cover during transportation and for storage.
AnEmissionControlLabelis locatedonthe engine. (Thisisan EXAMPLEONLY,information onlabelvaries byengine
FAMILY).
PRODUCT EMISSION DURABILITY
The 300 hour emission durability compliance period is the time span selected by the manufacturer certifying the
engine emissions output meets applicable emissions regulations, provided that approved maintenance procedures
are followed as listed in the Maintenance Section of this manual.
IMPORTANTENGINEINFORMATION
ENGINEFAMILY:7EHXS.0254KA DISPLACEMENT:25.4CC
EMISSIONCOMPLIANCE PERIOD: 300HRS.
THISENGINEMEETS U.S.EPAPHASE2EMISSION
REGULATIONS FOR SMALL NONROAD ENGINES. REFER TO
OWNER'S MANUAL FOR MAINTENANCE SPECIFICATIONS
ANDADJUSTMENTS.
EMISSION CONTROL
EPA Phase 2
The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for the fuel tank
theControlSystem isEVAP(Evaporative Emissions).Evaporativeemission maybeapplicable to Californiamodelsonly.

8
1
12
11
10
2
3
9
14
15
16
17
18
19
20
21 13
8
7
6
54
P/N 89016006361
Hot Decal (near muffler)
DESCRIPTION
Locate this safety decal on your unit. Make sure the decals are legible and that you understand and follow the instruc-
tions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING
instructionsforspecificinformation.
P/N 89016022660 22
Engine Cover

POWER PRUNERTM
OPERATOR'SMANUAL 9
1. POWERHEAD-IncludestheEngine,Clutch,FuelSystem,IgnitionSystemandStarter.
2. THROTTLETRIGGER-Springloadedtoreturntoidlewhenreleased. Duringaccelerationpresstriggergradually
for best operating technique.
3. SHOULDER HARNESS - An adjustable strap that suspends the unit from the operator.
4. CUTTINGATTACHMENT-Sealed,gearratiois1.5:1reduction.
5. CUTTING SHOE - Used to capture and stabilize branch while cutting. Place cutting shoe against branch, accelerate
and lower saw chain into branch.
6. GUIDEBAR-305mm(12in.)guidebarw/chaintensioner.
7. SAWCHAIN-91, 9.53mm(3/8in.)pitch,0.050gaugelowprofileOregon®sawchain. Runsapproximately610m/
min.(2000ft/min)atfullthrottle.
8. AUTOMATICOILERASSEMBLY-Selfoiling.Usehighquality,lowviscosity,non detergentbarandchainoil.
9. LOWERSHAFTTUBE-Durablefiberglassmeshhousing.
10. STOP SWITCH - Mounted on top of handle assembly. Move switch forward to run, back to stop.
11. THROTTLETRIGGERLOCKOUT-Thislevermustbedepressedbeforethrottletriggercanbeoperated.
12. REARHANDLEASSEMBLY-Sturdyhandleforrighthandplacement.Includesstopswitchandthrottletrigger.
13. TOPGUARD-Protectsarmfromhotengine.
14. SPARKARRESTOR-CATALYTICMUFFLER/MUFFLER-Themufflerorcatalyticmufflercontrolsexhaustnoise
and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep
exhaustareaclearofflammabledebris.
15. FUELTANK-Containsfuelandfuelfilter.
16. FUELTANKCAP-Coversandsealsfueltankopening.
17. PURGEBULB- Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from the
carburetor. Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump purge bulb
an additional 4 or 5 times.
18. RECOILSTARTER- Pull recoil handleslowlyuntilstarter engages,thenquicklyand firmly. Whenenginestarts
return handle slowly. DO NOT let handle snap back or damage will occur.
19. AIRCLEANERASSEMBLY-Containsreplaceableairfilterelement.
20. CHOKE - Located above air cleaner housing. Move lever to starting position ( ) (close choke) and back to run
position ( ) (open choke).
21. SPARKPLUG-Providessparktoignitefuelmixture.
22. GUIDE BAR COVER - Used to cover guide bar and saw chain during transport and storage. Remove guide bar
cover before using unit.

10
CONTENTS
Due to packaging restriction the ECHO product you have purchased requires some assembly.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing
parts. Use the contents list to check for missing parts.
__ PowerHead
__ Drive Shaft Assembly
__ Cutting Attachment W/ Guide Bar and Saw Chain
__ Operator's Manual
__ Safety Manual
__ Warranty Registration Card
__ Warranty Statement
__ T-Wrench (combination screwdriver/spark plug socket)
__ 4mmhexwrench
__ Safety Glasses
__ EchoPowerBlendTM 2-strokeoil sample
__ Shoulder Harness
__ GuideBarCover
ASSEMBLY
Tools Required: 10x19mm(13/32x3/4in)T-wrench, 4mmHex
Wrench,8x10mmWrench
Parts Required: PowerHead,Drive Shaft Assembly,
Cutting Attachment
DRIVE SHAFT / POWER HEAD
1. Loosen bolt (A).
2. Remove protective cap from drive shaft end.
3. Align flexible drive shaft coupler (B) with engine socket and slide
together until engine rests against lower drive shaft adapter (C).
IMPORTANT
Paintedend of flexible drive shaft coupler must always be
installed in engine socket when assembling engine to drive shaft.
4. Rotate lower drive shaft to align engine and rear handle assembly in
an upright position.
5. Tighten bolt (A) securely so engine will not rotate on lower shaft
tube.
BA
C
A

POWER PRUNERTM
OPERATOR'SMANUAL 11
WARNING
Saw Chain is sharp! Always wear gloves when handling assembly,
otherwise serious personal injury may result.
1. Loosen the four (4) screws (D) and locator screw (E) on cutting
attachment.
2. Loosen center clamp knob (F), turning counter clockwise.
3. Pulluppertube(G)outoffiberglasslowertube127-152mm(5-6in.),
then slide (G) back into fiberglass lower tube exposing inner drive
shaft (H). Align and join star shaped drive end of inner drive shaft
(H) with cutting attachment shaft (I).
4. Align ridges on upper tube (G) with seams in cutting attachment.
5. Slide together, aligning locator screw (E) in cutting attachment with
locating hole (J) in upper tube.
6. Tighten locator screw (E). Tighten four (4) cutting attachment
screws(D).
7. Extend upper tube to desired length. Tighten center clamp knob (F)
turningclockwise.
E
D
CUTTING ATTACHMENT TO DRIVE SHAFT INSTALLATION
E
D
F
G
H
G
HI
J
G

12
C
AB
D
E
THROTTLE LINKAGE AND IGNITION LEADS
1. Close choke and remove air filter and cover.
2. Place inner cable in slot of carburetor swivel (B).
3. Loosen nut (A) and place threaded end of throttle linkage in
bracket slot. Finger tighten nut (A).
4. Check throttle for freedom of movement and that wide open throttle
/ low idle extremes are adjusted properly. If adjustment cannot be
achieved with adjusting nuts, consult with your Echo Dealer for
correct adjustment procedure.
5. Tighten nut (A). Connect 2 ignition leads from throttle cable tubing
to 2 ignition leads (C) and (D) on engine.
6. Bundle and secure ignition leads against engine housing with clip
(E).
7. Installairfilter and cover.
SAW CHAIN TENSION ADJUSTMENT
WARNING
Always disconnect spark plug wire before servicing cutting
attachment. Wear gloves when handling saw chain, otherwise
serious personal injury may result.
To Adjust Saw Chain Tension.
1. Loosen two (2) 6 mm (13/32 in.) guide bar nuts (A) located on
cutting attachment.
2. Turn the adjuster slot (B) clockwise until saw chain touches the
bottom of guide bar. Turning adjuster slot (B) counter clockwise
will loosen saw chain on guide bar.
3. Tighten guide bar nuts firmly. Move saw chain backwards on
guide bar by hand. Saw chain should move freely on guide bar if it
is in proper mesh with sprocket. If saw chain is difficult to rotate or
binds on guide bar, it is too tight.
Keep the saw chain lubricated and properly adjusted and the guide bar
nuts tightened firmly at all times.
A
B

POWER PRUNERTM
OPERATOR'SMANUAL 13
OPERATION
NOTICE:Use ofunmixed,improperlymixed,or fuelolderthan90days, (stalefuel),maycausehard starting,poor
performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage
section of this manual.
FUEL
WARNING
Alternativefuels,suchasE-20(20% ethanol), E-85 (85% ethanol) or any fuelsnotmeetingECHOrequirementsare
NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels may cause performance prob-
lems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to,
improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets,
carburetors and other engine components.
Fuel Requirements
Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to
10%Ethanol (grainalcohol)or15%MTBE(methyltertiary-butylether).Gasoline containingmethanol (woodalcohol)is
NOTapproved.
TwoStrokeOil-Atwo-strokeengineoilmeetingISO-L-EGD(ISO/CD13738)andJ.A.S.O.FC Standardsmustbeused.
Echo brand premium Power Blend TM Universal 2-Stroke Oil meets these standards. Engine problems due to inadequate
lubricationcausedbyfailureto useanISO-L-EGD andJ.A.S.O.FCcertifiedoil, suchasEchopremiumPower BlendTM,
will void the two-stroke engine warranty. (Emission related parts only are covered for two years, regardless of two-
stroke oil used, per the statement listed in the Emission Defect Warranty Explanation.)
IMPORTANT
EchopremiumPowerBlendTM Universal2-StrokeOilmaybemixedat50:1ratioforapplicationinallEchoengines
sold in the past regardless of ratio specified in those manuals.
Handling Fuel
DANGER
FuelisVERYflammable.Useextremecarewhenmixing,storingorhandlingorseriouspersonalinjurymayresult.
• Use an approved fuel container.
• DONOTsmokenearfuel.
• DONOTallow flamesorsparks nearfuel.
• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.
• NEVERrefuelaunitwhentheengineisHOTorRUNNING!
• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.
•DONOToverfillfueltank. Wipeupspillsimmediately.
• Securely tighten fuel tank cap and close fuel container after refueling.
• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.
• Move at least 3m (10 ft.) from refueling location before starting the engine.

14
oitaR1:05-xiMliOotleuF
.S.UCIRTEM
SAGLIOSAGLIO
snollaG.zo.lFretiL.cc
1
2
5
6.2
2.5
31
4
8
02
08
061
004
Mixing Instructions
1. Fill an approved fuel container with half of the required amount of
gasoline.
2. Add the proper amount of 2-stroke oil to gasoline.
3. Close container and shake to mix oil with gasoline.
4. Addremaininggasoline, closefuelcontainer,andremix.
IMPORTANT
Spilled fuel is a leading cause of hydrocarbon emissions. Some
states may require the use of automatic fuel shut-off containers
to reduce fuel spillage.
After use
• DO NOT store a unit with fuel in its tank. Leaks can occur. Return
unused fuel to an approved fuel storage container.
Storage - Fuel storage laws vary by locality. Contact your local
government for the laws affecting your area. As a precaution, store fuel
in an approved, airtight container. Store in a well-ventilated, unoccu-
pied building, away from sparks and flames.
IMPORTANT
Stored fuel ages. Do not mix more fuel than you expect to use in
thirty (30) days, ninety (90) days when a fuel stabilizer is added.
IMPORTANT
Stored two-stroke fuel may separate. ALWAYS shake fuel
container thoroughly before each use.

POWER PRUNERTM
OPERATOR'SMANUAL 15
Automatic Oiling System
1. Wipedebrisfromaroundoil fill cap.
2. Removeoilfillcap andfillreservoirwith a quality,lowviscosity
guide bar and saw chain oil.
NOTE
The discharge volume of the automatic oiler is preset to deliver 3 to
4 cc/min. at normal operating RPM. During heavy or dry cutting
conditions the oil discharge volume may be adjusted to assure
adequate lubrication. Refill the oil reservoir with each tank of fuel.
IMPORTANT
To prevent plastic deterioration, do not use synthetic or silicone
based oil.
ADJUSTINGAUTOMATIC OILER
Toolsrequired: 10x19mm(13/32x3/4)T-Wrench
1. Remove two (2) 6 mm guide bar retaining nuts and sprocket cover.
2. From bottom of gear case, turn adjustment screw (A) clockwise to
decrease oil volume - counter clockwise to increase oil volume.
NOTE
Verylittlevisibleoilonthesawchainwillprovidesufficient
lubrication.
3. Assemble components in reverse order.
LUBRICATING THE GUIDE BAR AND SAW CHAIN
A

16
STARTING COLD ENGINE
WARNING
The attachment will operate immediately when the engine starts and
could result in loss of control and possible serious injury. Keep
movable parts of the attachment off the ground and away from
objects that could become entangled or thrown.
1. Stop Switch
Move stop switch button (A) forward away from the STOP
position.
2. Choke
Move choke (B) to “Cold Start” ( ) Position.
3. Purge Bulb
Pump purge bulb (C) until fuel is visible and flows freely in the clear
fuel tank return line. Pump bulb an additional 4 or 5 times.
4. Recoil Starter
Lay the unit on a flat, area and keep movable attachment parts clear
of all obstacles. Firmly grasp right hand grip and throttle trigger
lockout with left hand and fully depress throttle trigger to wide
open position. Rapidly pull recoil starter handle/rope (D) until
enginefires(ormaximumfive[5]pulls).
5. Choke
After engine fires (or five [5] pulls), move choke lever back to
“Run” ( ) position. Hold throttle trigger and throttle trigger
lockout fully depressed and pull recoil starter handle/rope until
engine starts and runs. Release throttle trigger and allow unit to
warm up at idle for several minutes.
NOTE
If engine does not start with choke in “Run” position after 5 pulls,
repeat instructions 2 - 5.
6. After engine warms up, gradually depress throttle trigger to
increase engine RPM to operating speed.
A
B
C
D

POWER PRUNERTM
OPERATOR'SMANUAL 17
STARTING WARM ENGINE
The starting procedure is the same as Cold Start except DO NOT close
the choke, and do not depress throttle trigger to wide open position.
WARNING
The attachment should not move at idle, otherwise serious personal
injurymayresult.
NOTE
If attachment moves, readjust carburetor according to “Carburetor
Adjustment” instructions in this manual or see your ECHO Dealer.
1. Stop Switch.
Move Stop Switch button (A) forward away from the STOP
position.
2. Purge Bulb
Pump purge bulb (C) until fuel is visible and flows freely in the clear
fuel tank return line. Pump bulb an additional 4 or 5 times.
3. Recoil Starter.
Lay the unit on a flat, clear area and firmly grasp right hand grip
with left hand. Do not depress throttle trigger. Pull the recoil
starter handle (D) until the engine fires.
NOTE
If engine does not start after 5 pulls, use Cold Start Procedure.
A
C
D

18
STOPPING ENGINE
1. Throttle.
Release throttle trigger, and allow engine to return to idle before
stopping engine.
2. Stop Switch.
Move stop switch button (A) backward to STOP position.
WARNING
If engine does not stop when stop switch is moved to STOP
position, close choke - COLD START position - to stall engine.
Have your ECHO dealer repair stop switch before using pruner
again.
PRUNING TECHNIQUES
ThePowerPrunerTM isdesigned forlighttomedium trimmingoflimbs
and branches up to 203 mm (8 in.) in diameter. Follow these tips for
successful operation.
• Plancutcarefully.Checkdirectionbranchwillfall.
• Plan retreat path from falling branch. Cut branches bounce when
striking ground.
• Long branches should be removed in several pieces.
• Do not stand directly beneath branch being cut.
• When ready to cut:
Hold "cutting shoe" against branch. This will prevent whipping of the
branch. DO NOT use back and forth sawing action.
• Look out for branch immediately behind the branch being cut. If saw
chain hits rear branch damage to saw chain may occur.
• Accelerate to full throttle.
• Apply cutting pressure.
• Ease cutting pressure when nearing end of cut to maintain control.
• Whenpruning alimb 102mm (4in.)diameterorlargercutasfollows:
1. Undercut1/4 limbdiameter neartreetrunk.
2. Finish top cut slightly farther out on limb.
3. Flush cut stub at trunk.
• DONOTuse forfellingorbucking.
A
CORRECT
GUIDEAGAINST
BRANCH
BLADEHITSREARBRANCH
NOT
CORRECT
NOT
CORRECT

POWER PRUNERTM
OPERATOR'SMANUAL 19
MAINTENANCE
Your ECHO Power PrunerTM is designed to provide many hours of trouble free service. Regular scheduled maintenance
will help your pruner achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to
takeyourunitto an ECHO Service Dealerformaintenance. Tohelpyou decide whether you wanttoDO-IT-YOURSELF
or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed see your ECHO Dealer for
repairs.
SKILL LEVEL
Level1= Easy to do. Most required tools come with unit.
Level2= Moderate difficulty. Some specialized tools may be required.
Level3= Experiencerequired.Specializedtoolsarerequired.ECHOrecommends
that the unit be returned to your ECHO dealer for service.
ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier. Just below each task
heading are listed the various part numbers required for that task. See your ECHO dealer for these parts.
MAINTENANCE INTERVALS
/TNENOPMOC
METSYS
ECNANETNIAM
ERUDECORP
D'QER
LLIKS
LEVEL
ROYLIAD
EROFEB
ESU
YREVE
LEUFER
3
SHTNOM
09RO
SRUOH
6
SHTNOM
072RO
SRUOH
YLRAEY
006
SRUOH
serudecorPecnanetniaMrelaeDohcEdednemmoceR
troPtsuahxErednilyCnobraceD/naelC/tcepsnI 3C/I
serudecorPecnan
etniaMflesruoY-tI-oD
retliFriAecalpeR/naelC/tcepsnI 1C/I*I
metsySekohCnaelC/tcepsnI 2C/I
retliFleuFecalpeR/tce
psnI 1I*R/I
skael,metsySleuFecalpeR/tcepsnI 1*)1(R/I)1(I)1(I
metsySgnilooCnaelC/tcepsnI 2C/I
rotserrAkrapSrelffu
MecalpeR/tcepsnI 2*R/I
gnisuoHtfahSevirDnaelC/tcepsnI 2C/II
raBediuGetacirbuL/naelC/tcepsnI 2*C/II
niahCwaS/ecalp
eR/neprahS/tcepsnI
etacirbuL
2*R/II
epoRretratSlioceRnaelC/tcepsnI 1*R/I
gulPkrapSnaelC/tcepsnI 2C/I*R
stloB/stu
N/swercSecalpeR/nethgiT/tcepsnI 1*R/I
SEDOCRETTELERUDECORPECNANETNIAM NAELC=C,ECALPER=R,TCEPSNI=I:
-ETONTNATROPMI deriuqerfoycneuqerfehtenimretedlliwecneirepxeruoydnaesulaut
cA.mumixameranwohsslavretniemiT
.ecnanetniam
:SETONERUDECORPECNANETNIAM
)1( .ytirgetninoissimeniatniamotecnanetniamralugereriuqerTONODsknatleufevitaropavewoL
*.noitcepsnigniru
draewroegamadfognidnifehtnodesaberaecalperotsnoitadnemmocerllA

20
AIR FILTER
Level1.
Tools required: Cleaningbrush25or50mm(1or2in.)
Parts required: 90030REPOWERTM AirandFuelFilter Kit
1. Close choke (Cold Start Position [ ]). This prevents dirt from
entering the carburetor throat when the air filter is removed. Brush
accumulateddirtfromaircleanerarea.
2. Removeairfiltercover.Brushdirtfrominsidecover.
3. Removeairfilterandlightlybrushdebrisfromfilter.Replacefilterif
it is damaged, fuel soaked, very dirty, or the rubber sealing edges
aredeformed.
4. If filter can be reused, be certain it:
• Fits tightly in the air filter cavity.
• Is installed with the original side out.
5. Installairfiltercover.
NOTE
Carburetor adjustment may be needed after air filter cleaning/
replacement. See Carburetor Adjustment Section.
FUEL FILTER
Level1.
Tools required: 200-250mm (8-10in.)lengthofwirewithoneend
bent into a hook, Clean rag, funnel, and an approved
fuel container
Parts Required: 90030REPOWERTM AirandFuelFilter Kit
DANGER
FuelisVERYflammable.Useextremecarewhenmixing,storingor
handling or serious personal injury may result.
1. Use a clean rag to remove loose dirt from around fuel cap and
emptyfueltank.
2. Use the “fuel line hook” to pull the fuel line and filter from the tank.
3. Removethefilterfrom the line andinstallthe new filter.