EchoStar DSB-1100 User manual

User Manual
EMBEDDED VIACCESS
DIGITAL SATELLITE RECEIVER

CONTENTS
3.
4. Remote Control Unit (RCU) ------------------------------------------------------- 5
5. Getting started ------------------------------------------------------------------------ 6
6. Operation and menu program ------------------------------------------------------ 8
7. Specifications ------------------------------------------------------------------------- 19
Front & Rear view ------------------------------------------------------------------- 4
2. Features ------------------------------------------------------------------------------- 3
1
Trade Mark of the DVB Digital Video Broadcasting Project (1919)
A. Receiver and TV set-up ------------ --------------------------------------------- 8
B. Main menu & Installation ---------------------------------------------------- 11
C. Advanced Installation --------------------------------------------------------- 17
Safety instructions ------------------------------------------------------------------- 21.
AC power switch is on the rear panel of the receiver.
AC power switch is on the rear panel of the receiver.

WARNING!
Always follow these instructions to avoid the risk of injury to yourself or damage to your equipment.
Unplug the receiver from the AC power outlet before cleaning. Use only a damp cloth for cleaning
the exterior of the receiver.
Do not use accessories or attachments not recommended by the receiver manufacturer, as they may
cause hazards and will void the warranty.
Do not operate the receiver in high-humidity areas, neither expose it to water or moisture.
Do not place the receiver on an unstable cart, stand, tripod, bracket or table. The receiver may fall,
causing serious personal injury and damage to the receiver.
Do not block or cover slots and openings in the receiver. These are provided for ventilation and
protection from overheating. Never place the receiver near or over a radiator or heat register. Do
not place the receiver in an enclosure such as a cabinet without proper ventilation.
Do not stack the receiver on top of or below other electronic devices.
Operate the receiver using only the type of power source indicated on the marking label. Unplug the
receiver power cord by gripping the power plug, not the cord.
Route power supply cords so that they are not likely to be walked on or pinched by items placed upon
or against them. Pay particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the unit.
Use an outlet that contains surge suppression or ground fault protection. For added protection during
a lightning storm, or when the receiver is left unattended and unused for long periods of time, unplug
it from the wall outlet and disconnect the lines between the receiver and the antenna. This will
provide some protection against damage caused by lightning or power line surges.
Do not attempt to service the receiver yourself, as opening or removing covers may expose you to
dangerous voltage, and will void the warranty. Refer all servicing to authorized service personnel.
Unplug the receiver from the wall outlet and refer servicing to authorized service personnel whenever
the following occurs:
The power supply cord or plug is damaged;
Liquid has been spilled, or objects have fallen into the receiver;
The receiver has been exposed to rain or water;
The receiver has been dropped or the chassis has been damaged;
The receiver exhibits a distinct change in performance.
2
1. Safety Instructions

2. Features
3
1. MPEG-2 Video (MP@ML)
2. MPEG-1 Audio layer 1, layer 2
3. MPEG-2 Digital & fully DVB compliant
4. EmbeddedViaccess with 1 smart card reader
5. LD quality video, CD quality audio
6. Capable of scanning the frequency for SMATV system
7. Plug & Play installing program set-up
8. Proprietary EchoStarOSG menu for full integrated functions
9. On-screen display with 256-color full resolution
10. Variety of LNB polarity control; 13/18V, 0/22KHz tone, 0/12V and DiSEqC LNB
11. RS232C port for additional information service and update of the receiver control software
12. 4-digit 7-segment LED on the front panel display channel information
13. SCPC/MCPC receivable from C/Ku-Band satellites
14. Displays local time on the front panel in stand-by mode
15. Displays signal level to set up the satellite antenna with ease
16. 64-step volume control
17. Powerful editing facilities ; PIDs, TV or Radio Channel, Channel Name, Satellite Name/Transponders
18. Teletext supported (Your TV should support teletext)
19. Subtitle supported (with optional background)
20. Power recovery function
21. Favorite channel function (up to 96 channels)
22. Last channel memory function
23. Capable of receiving unencrypted free digital programs
24. Variable aspect ratio (4:3, 16:9) with pan vector
25. EPG for on-screen channel information
26. Parental lock / Installation&Edit lock / Receiver lock
27. Multi-lingual function when provided by the satellite and program provider
28. Total 2,000 channels programmable (TV: 1,500 CH. & Radio: 500 CH.)
29. DiSEqC 1.2TM compatible
29. Receiver to receiver function for program and data transmission

ANT IN
TV OUT
VIDEO
AUDIO
(400mA Max)
Front Panel
Front Panel
3. Front & Rear View
Rear Panel
Rear Panel
4
Note: All the cables used for Input/Output connection for the receiver should be well shielded.
Note: All the cables used for Input/Output connection for the receiver should be well shielded.
AC power cord
RF output connector to TV
Antenna input LNB input
AC power switch
Smart card slot Channel up/down On/Standby
Selection/confirmation
Volume up/down

4. Remote Control Unit (RCU)
5
The Power key turns the receiver on and off.
The Volume and Channel keys control the two most frequently used
functions of the receiver. The OK key is used to select a program, a
highlighted line or parameter value. Also you can see TV/Radio
channel list while watching TV or listening to the radio.
The Mute key switches the sound on and off.
The MENU key is used to see main menu or to return to previous
menu.
The cursor keys are for channel ?and ?and volume ?and ?.
The EXIT key exits to the video viewing mode at any time.
Number / Inputkeys enable direct channel selection command
using numeric keys.
The TV/RAD(Radio) key switches between TV and radio mode.
The EPG key shows program information of the selected channel.
(EPG; Electronic Program Guide)
The Subtitlekey enables subtitling (only when provided by the
broadcaster).
Selects the Audio Language or Soundtrack from among the data
transmitted for the current channel.
Shows a thumb nail representation of the current channel in the “Edit TV Channel”,
“Parental Lock”and “EPG”.
The SATkey shows a list of selectable satellite.
The Information provides additional information about the
current channel and program (only available when provided by
the broadcaster). In the menus, pressing this key provides up to
four lines of help.
-
The FAV key shows a list of your selected favorite channels
(To define channels as favorite select the “Edit TV channel”
menu).

ANT IN
TV OUT
VIDEO
AUDIO
(400mA Max.)
ANT IN
TV OUT
VIDEO
AUDIO
(400mA Max.)
DO NOT PLUG the receiver into Main Power Outlet, until you complete all the connections to the receiver.
DO NOT PLUG the receiver into Main Power Outlet, until you complete all the connections to the receiver.
5. Getting Started
TV ANTENNA
TV
RF IN
6
Receiver to TV with RF
VCR
TV
RF IN RF IN RF OUT
Receiver to VCR and then to TV with RF
1. Connect the Off-air TV antenna or cable if available to the ANT IN socket of the EchoStar DSB-1100 Viaccess.
2. Connect the TV OUT socket of theEchoStar DSB-1100 Viaccessto the RF IN of the TV set.
3. Search on the TV set for UHF channel # 38. This is the default channel where theEchoStar DSB-1100 Viaccessis set to.
1. Connect the Off-air TV antenna or cable if available to the ANT IN socket of the EchoStar DSB-1100 Viaccess.
2. Connect the TV OUT socket of theEchoStar DSB-1100 Viaccesswith the RF IN of the VCR.
3. Connect the RF OUT of the VCR to the RF IN of the TV set.
4. Search on the TV set and the VCR for UHF channel # 38. This is the default channel where the EchoStar DSB-1100 Viaccess
is programmed to.
Note : Use different UHF channels for VCR and EchoStar DSB-1100 Viaccess.
TV ANTENNA

ANT IN
TV OUT
VIDEO
AUDIO
(400mA Max.)
ANT IN
TV OUT
VIDEO
AUDIO
(400mA Max.)
TV ANTENNA
TV
RF IN
7
Receiver to TV with Audio and VideoRCAs
VIDEO AUDIO
IN IN
Receiver to TV and VCR with SCART Cables
1. Connect the Off-air TV antenna or cable if available to the ANT IN socket of the EchoStar DSB-1100 Viaccess.
2. Connect the TV OUT socket of theEchoStar DSB-1100 Viaccesswith the RF IN of the VCR.
3. Connect the RF OUT of the VCR to the RF IN of the TV set.
4. Search on the VCR for UHF channel # 38. This is the default channel where the EchoStar DSB-1100 Viaccess is programmed to.
5. Connect the SCART cable from the TV SCART of the EchoStar DSB-1100 Viaccess to the SCART of the TV set.
6. Connect the SCART cable from the VCR SCART of theEchoStar DSB-1100 Viaccessto the SCART of the VCR.
7. When the EchoStar DSB-1100 Viaccess is switched on the TV set, it will automatically switch to the SCART input of the TV.
Note : Use different UHF channels for VCR and EchoStar DSB-1100 Viaccess.
TVSCART RF IN RF OUT RF IN VCR SCART
1. Connect the Off-air TV antenna or cable if available to the ANT IN socket of the EchoStar DSB-1100 Viaccess.
2. Connect the TV OUT socket of theEchoStar DSB-1100 Viaccesswith the RF IN of the TV set.
3. Connect the Video and Audio RCAs of the EchoStar DSB-1100 Viaccess to the Video and Audio RCAs of the TV set.
TV ANTENNA VCR
TV

A. Receiver and TV set-up
Check the Installation
To get the most out of the EchoStar DSB-1100 Viaccess it should be correctly installed, the dish should be
optimally aligned and the mechanical limit switched on the dish should be set properly. Press /I on the
remote control unit (RCU) or press on the front panel of the EchoStar DSB-1100 Viaccess.
5. Operation and Menu Program
8
The receiver is supplied with factory setting and will start up with the “Language Setting”menu. For more
information on the “Language Setting”menu, please see page 9. Please follow the steps outlined below to
properly install the EchoStar DSB-1100 Viaccess.
LNB Setting
Select the LNB type which conforms to your LN
B using the , keys.
Other parameter values should be changed
manually according to your LNB type.
Press the OKkey to confirm your selection.
Select the “LNB Setting”menu in the “Installation”m
enu using the , keys.
LNB Setting
LNB Freq.Low 5150
LNB Frq. High 5150
Switch Type DiSEqC 1..4
Switch Port 1
Polarity Control 13/18V
LNB Freq. Band Control 0/22kHz
Ku/C Control Disable
LNB Type Index (1..8)
0/22kHz Control Off
0/12V Control Off
LNB Power On
1
2
43
5
6
7
8
9
10
11
×Type 1 Ø
i
Program Satellites
If you are unable to get any signal quality, please check the LNB Setting to ensure you have selected the corr
ect LNB and switch settings.
This menu is to align your dish to the selected satellite.
After setting the parameters, press the OK key to store th
e parameter values. And Start Search(Press OK) to searc
h the channels of transponder you want.
Refer to the Signal Quality bar and the Signal Lev
el bar at the bottom of the screen. It is recommend
ed that the signal is at the Medium level or higher.
If it is not , please adjust your satellite dish. 8
7
Program Satellite
Satellite 028.2°E
LNB Type Type1
TP/Polar 11478/H
Symbol Rate 30000
Position
Step Move E W
Search type Auto Search
Start Search(Press OK)
2
3
4
Set
Signal Level
Signal Quality
6
52%
63%
×ASTRA2 Ø
5
i
1
8

User’s Setting
9
User’s Settings are only accessible via the Installation screen.
Language Setting
Subtitle
None
Eng
Ita
Subtitle
Select the “Subtitle Language”in the “Language Setting”
menu. While viewing a channel, the subtitling option is
available only when the selected subtitling language is
provided by the broadcaster.
To check if the subtitling language is available, press the
“”key on the remote control unit, to show a list with all
available subtitling languages.
You can selecta different language for the OSG (On-Screen Graphics) display using the , keys when the
“Menu Language”option is selected. Similarly you can select a different audio channel when the “Audio
Language”option is selected. This option allows you to select a different language to listen to if supported.
Language Setting
Menu Language
Main Audio Language English
×English Ø1
22nd Audio Language English
Subtitle Language English
3
4
Exit
i
User’s Setting
Local Time Setting
A/V Output Setting
About Echostar
Language Setting
3
1
4
2
Exit
i
DiSEqC 1.2 Mount
In case you are using the DiSEqC positioner, you should set the
most east satellite and most west satellite you want on the
“Position”bar.
- Most Eastern satellite : change the satellite name into you want
by the most east satellite on the “Satellite”bar and
move to “Position”bar and press the Volume down key(×)
until the Signal Level is at the medium level or higher.
And press the OK key to store this satellite as the most east
satellite.
- Most Western satellite : change the satellite name into you
want by the most west satellite on the “Satellite”bar
and move to “Position”bar and press the Volume up key(Ø)
until the Signal Level is at the medium level or higher.
And press the OK key to store this satellite as the most west
satellite.
Then, start the “Auto Search”to search and store the TV channels and Radio channels of the satellite automatically.
LNB
FIXED DISH
DiSEqC 1.2
Switch
LNB IN

Please select your TV format.
4:3 for normal screen TV
16:9 for wide screen TV
Aspect
A/V Output Setting
10
About EchoStar
You can see the details of the company
information.
If you have any questions about the EchoStar
DSB-1100 Viaccess, firstly contact your local d
ealer.
You can select the time out
time(2,3,4,5,8,10 secs) of the banner
information about the current channel and
program using the , keys.
Banner
You can select the type of Video standard by using the , keys.
* Video standard : PAL B/G,I , D/K
Select the vacant channel considering your local channels and preset channels below.
* Pre-set : Ch 38 for PAL B/G, I Ch 40 for PAL D/K
UHFfrequency is set automatically according to the channel selection.
UHF Tuning
Sub.backg.Select ‘On’for Subtitle background on TV (Subtitle background).
i
Company info
Exit
Company Echostar Intl. Corp.
Address Schuilenburglaan 5a
City 7604 BJAlmelo
About Echostar
Fax number [phone]
Phone number [phone]
Country Netherlands
Unit DSB-1100Viaccess
Software version XXXXXX
Home page HTTP://www.echostar.nl
Unit info
A/V Output Setting
Aspect
Banner 3sec
Sub. backg. On
PAL B/G
TV mode 607.25MHz
Channel 38
<<<UHF Tuning >>>
2
3
5
4
iExit
×4:3 Ø
1
Local Time Setting
Local Time Setting
GMT usage
Selected time zone London
Summer time Off
Time offset +00
Local Time = --:--
1
3
2
4
iExit
×Yes Ø
A) If GMT is provided
Select Yes for GMT usage, the area of the selected place (time zone) and summer time On/Off.
You can adjust the time from +59 to -59 minutes by using the time offset.
(Please be aware that GMT information from broadcaster may not always be correct.)
B) If GMT is not provided or you want to set the time yourself, select No for GMT usage, the area of the
selected place and set your local time using the ×Økeys.
If GMT is provided by the broadcaster, you may get
the time using the GMT provided by broadcaster (or)
you may get your own time. (Please be aware that the
GMT information provided by the broadcaster may
not be correct sometimes.)

11
Installation
B. Main menu and Installation
Press the MENU key to display the “Main Menu”o
n the screen.
Main Menu
Select a sub-menu using the , keys or the numeric k
eys. Please note that the OK key is always a confirma
tion of your selection. To go back to the previous me
nu, press the MENU key.
The Installation, “Enter PIN code”Menu is displayed only when the Installation&Edit Lock is set as [O
N]. The initial code is set as[0000] but you can change it (See “Change PIN code”on page 13).
Program Satellites
If you are unable to get any signal quality, please check the LNB Setting to ensure you have selected the corr
ect LNB and switch settings.
This menu is to align your dish to the selected satellite.
After setting the parameters, press the OKkey to store th
e parameter values. And Start Search(Press OK) to searc
h the channels of transponder you want.
Refer to the Signal Quality bar and the Signal Lev
el bar at the bottom of the screen. It is recommend
ed that the signal is at the Medium level or higher.
If it is not , please adjust your satellite dish.
Main Menu
TVChannels
Radio Channels
Parental Control
Edit
Installation
SelectSatellite
32
4
5
6
Exit
i
1
Enter PIN Code
[ ? ? ? ?]
Installation Lock Installation
SMATV Configuration
User’s Setting
LNB Setting
ProgramSatellites
1
43
5AdvancedInstallation
2
Exit
i
8
7
Program Satellite
Satellite 028.2°E
LNB Type Type1
TP/Polar 11478/H
Symbol Rate 30000
Position
Step Move E W
Search type Auto Search
Start Search(Press OK)
2
3
4
Set
Signal Level
Signal Quality
6
52%
63%
×ASTRA2 Ø
5
i
1
8
7 Conditional Access

Note: To stop searching press the key on the
Using the Auto Search option, the EchoStar DSB-110
0Viaccess searches for all available channels (Radio
and TV) on the currently selected satellite. The names
of the found TV channels are shown on the left and th
e total number of found TV and Radio channels are m
entioned on the right.
Auto Search
A Satellite Master Antenna Television (SMATV) system
which is intended for the distribution of television and
sound signals to household in one or
6more adjacent buildings.
A SMATV System represents a means for sharing
the same resources among several users for satellite and
terrestrial reception, and it is designed to perform
the adaptation of the satellite TV signals to the SMATV
channel characteristics.
This receiver has a SMATV-IF facility to operate with SMATV.
This configuration allows the direct distribution of the QPSK signal received from the satellite
to the SMATV-IF distribution network in the extended IF band (above 950 MHz).
Before you start, you have to check your condition whether it is possible to use this facility or not in your
households. (You can ask your household supervisor.)
If this receiver is connected to a SMATV network, select “SMATV Configuration”.
The most common alternatives for “Symbol rate”and “FEC”are already preprogrammed.
(When you need to change the “Symbol rate”for the exceptional frequency, select as you know.)
Move to “Start Auto Search”and just press the OK key.
Then, the “Auto Search”procedure will start.
To cancel the processing while the “Auto Search”is proceeding, press the MENU key.
SMATV Configuration
12
SMATV Configuration
Symbol rate alternative 2 27500
Symbol rate alternative 3 27500
FEC AUTO
Start Auto Search
Symbol rate alternative 11
2
43
5
×27500 Ø
i
Exit
Auto Search ASTRA1
Channel Searching Status
0% 50% 100%
Found TV Ch. : 240
Found Rad. Ch. : 100
Index Freq SR FEC Polarity
45 12670 22000 5/6 vertical
Arte
Beta BC
BD1
Estilo
Musicals
Reqqae
remote control or on the front panel. This
cancels the searches and the found
channels will be discarded. All other keys
of the remote are disable during searching

13
Parental Control
With parental control it can be prevented that a TV channel can be watched, a Radio Channel can
be heard, the receiver settings can be changed or an unauthorized change in the installation is
performed.
TV Channels
You can select the channel you would like to watch either b
y pressing the numeric keys for the channel number or by m
oving the highlighted bar to the channel of your choice usin
g the , keys. Press the OK key to select the channel.
* Press the ,keys to move one page up or down.
Radio Channels
The pre-programmed PIN (Personal Identification Number) code is set as
[0000]. If you want to change it, please follow the procedure shown as
before.
Change PIN Code
Enter PIN Code
[ ? ? ? ?]
Parental Control
Exit
i
Parental Control
TV Channel Lock
Radio Channel Lock
Receiver Lock Off
Installation&Edit Lock Off
Change PIN code1
2
43
5
Exit
i
You can select the channel you would like to watch either b
y pressing the numeric keys for the channel number or by m
oving the highlighted bar to the channel of your choice usin
g the , keys. Press the OK key to select the channel.
* Press the ,keys to move one page up or down.
After selecting your wanting radio channel, the picture of t
he last TV channel is displayed.
TVChannels
Voyage F
Contact TV F
LC I F
Cabal J F
Paris Premere F1
2
4
3
5
ASTRA1 019.2?E >
6
87JDF 1 Info-Kanal F
Star Kino F
CNBC Europe F
9
10 Zee TV F
JSTV S
Radio Channels
Hit Liste F
Classic rock F
Soft Rock F
2
3
4
Blues F
Generation ROC F
Love Songs F
Dance F
Radio Evira F
5
76
8
ASTRA1 < 019.2?E >
1
9
10 BBC Radio3 F
BBC Radio1 F

14
You can not enter directly into the installation menu and Edit menu when the Inst
allation&Edit Lock is ON.
Press the OK key to lock / unlock the selected chan
nel.
The letter color of the locked channels will be chang
ed into Grey color on the “TV Channels”menu.
Note) The color of the highlighted bar turns to red
when it is on a locked channel.
Installation&edit
Lock
TV Channel Lock TV Channel Lock
Voyage
ContactTV
LC I
Canal J
Paris Premere
1
2
4
3
5
6
8
7 DF 1 Info-Kanal
Star Kino
CNN
Lock Unlock Exit
i
If the Receiver Lock is [ON], you have to input the correct code to operate
the receiver.
Receiver Lock
Press the VIEW key to see a thumb nail of the current
channel in this menu.
You can create a group of up to 200 channels in the
“Edit TV Channel”or “Edit Radio Channel”
menu. To include a channel in the FAV list, select a
channel and press the bluekey on the remote control.
To select a favorite channel from the FAV list, press
the FAV key.
To view a thumb nail representation of the currently
selected channel, press the VIEW key on the remote
control.
FAV Channels Edit TV Channel
Voyage
ContactTV
LC I
Canal J
Paris Premere
5
2
43
6
87DF 1 Info-Kanal
Star Kino
CNN
ASTRA1
Delete Cancel Move Favorite Exit
i
1
You can move to the channel that you want to edit by using , keys.
Also you can move to the highlighted bar directly by inputting the channel number.
Press OK to select the channel you want to edit, and then you can move the channel to the position you
want or delete it.
Edit TV Channel
Edit
Edit TV Channel
Edit Radio Channel
EditTransponder
EditSatellite
2
3
4
Exit
i
1
52
51
Edit TV Channel
Paris Premere
Voyage
ContactTV
LC I
50
ASTRA1
Delete Cancel Move Favorite Exit
i
56
55
53
54 Canal J
DF 1 Info-Kanal
Star Kino
CNN
49
The “Enter PIN code”Menu is displayed only when the Installation&Edit Lock is set as [ON]. The initia
l code is set as [0000]but you can change it (See “Change PIN code”on page 13).

15
Edit Radio Channel
Use the same procedure for the Radio Channel
s as used for editing the TV Channels as above.
Edit Radio Channel
Hit Liste
Blues
Classic Rock
Soft Rock
2
3
4
ASIASAT2
Generation ROC
Love Songs
Dance
REE
5
76
8
Delete Cancel Move Favorite Exit
i
1
Edit Satellite
To delete a transponder, press the red keywhen the
highlighted bar is located at the transponder you
want to delete.
To add a transponder, press the blue key.
And then, “Edit/Add SAT or TP”menu will be displaye
d, and you can add a transponder in that menu.
Edit Transponder
Select Satellite
To move to another satellite you want to watch, press the
SATkey on the remote control and choose the proper
satellite with , keys.
Press the OKkey to confirm.
EditSatellite
ASTRA11
ExitDelete Cancel Add SAT
Satellite Name
i
SelectSatellite
APSTAR2R
ASTRA1
1
2
Exit
i
To delete a satellite, press the red key when the
highlighted bar is located at the transponder you
want to delete.
To add a satellite, press the blue key.
And then, “Edit/Add SAT or TP”menu will be displaye
d, and you can add a satellite in that menu.
EditTransponder
Network(3713H)
Network(3720H)
2
3
4
1Network(3706H)
ASIASAT2
Network(3727H)
Network(3734H)
Network(3764H)
Network(3766V)
5
6
8
Channel List
CHANNEL ONE
Ch.8 - OS Down
Ch.9 - OS Down
Ch.370.Audio
Ch 371.Audio
Ch.372.Audio
Ch.373.Audio
Ch.374.Audio
Ch.375.Audio
Network(3661H)
Exit
Delete Cancel Add/ TP
i
7

16
ALT Audio
If more than one audio channel is provided by
the broadcaster on a specific channel, you can
activate the audio mode display by pressing the
key.
L Audio R
1
LR
L Audio R
Guide
While watching or listening to any channel and you
want to know more information regarding the
program shown, press the EPG key on the remote
control to display the “TV Guide”or the “Radio
Guide”. This information may be provided by the
broadcaster. You can move to another channel by
pressing the , keys or the ,keys.
Please refer to the function of the keys belows.
Pressing the Yellow(Info) key shows the detailed
information of the program and thumbnail of the
current channel.
TVGuide
RAI1 Linea verde- In ?11:10~11:55
RAI2 No Information No Time
RAI3 Rai Sport Cavale ?11:27~12:02
RAIwidescree Wide Screen 11:00~14:00
2
3
4
Radio Next Info Select Exit
i
1
5
6
7
11:52
Now
RAISPORT sate Rai Sport Sat 11:00~14:00
TEST2RAI No Information No Time
TEST3RAI No Information No Time
1) Red(TV/Radio) key : Switches the “TV Guide”and the “Radio Guide”by pressing this key.
2) Green(Now/Next) key : Switches the program guides of “Now”and “Next”
3) Yellow(Info) key : Shows detailed information of the selected channel.
4) Blue(Select) key : Goes to the viewing mode of the selected channel.
5) White(Exit) key : Exits the TV/Radio Guide
TVGuide
EPG Select Exit
i
RAI1
natura: Linea verde - In diretta dalia natura
Un programma di Sandro Vannucci a cura do
Gian Stefano Snoto produttore esecutivo
Gianoiero Ricci
11:19~11:55
8CNN No Information No Time
Conditional Access Conditional Access
1
Exit
i
Smart Card Information
Viaccess Embedded
< Viaccess Embedded >
Insert the Viaccess smart card into the Smart Card slot
on the Front Panel. The chip should be faced
upwards.

17
Advanced Installation
Edit/Add SAT or TP
C. Advanced Installation
Reset(Factory Default)
Edit/Add SAT or TP
AdvancedInstallation
Edit LNB Local Freq.2
3
1
Exit
i
You can select the “Advanced Installation”menu
on the “Installation”menu of Main menu by using
the Channel up/down keys (Ù,Ú).
You can edit a pre-programmed satellite name and a
dd a new one in this menu.
Also you can edit and add Transponder Frequency p
arameter by using the ×,Økeys.
To add a new satellite name, press OK after moving
to [ ???????? ] mode for satellite, then the graphic ke
yboard will be activated. After entering new satellit
e name and press OK on the“Save”on the keyboard.
And then, you can set each parameters by giving the
data for Transponder Freq., LNB Polarization and Sy
mbol Rate.
To edit an additional transponder on a pre-programmed satellite, you should input all the required data after mo
ving to the satellite you want to edit.
CAUTION) By doing an Auto Search you will lose all the data (ex. FAV, Lock…)
which you have edited.
Note 1) You should execute “Auto Search”after editing the satellite or the transponder.
If Auto Search is executed after adding the new transponder, all channels of the added
Transponder will be searched and stored automatically.
Note 2) You can add or edit totally of 50 satellites. This includes the pre-programmed
satellites. The receiver has the capability to store up to 999 transponders and
2000 channels.
Satellite
Longitude 019.2 °E
Index 1
TP/Signal Quality 0
LNB polarization Vertical
Symbol Rate 0
Channel Name ????????
FEC AUTO
Edit/Add SAT or TP
3
2
5
6
7
8
4
1
9
10
11
Video PID 0
PCR PID AUTO
Audio PID 0
×ASTRA1 Ø
i

You can edit up to 8 local frequencies by using
numeric keys.
And if you want to save newly edited frequency,
press the OK key.
18
If you want to reset all the data edited, press the red ke
y twice.
Edit LNB Local Frequency
Reset (Factory Default)
Edit LNB Local Frequency
LNB Local Freq. 0..9 ×11300 Ø
Exit
i
Reset (Factory Default)
* If you want Factory Reset, press Red button
Reset Cancel Exit
i

19
6. Specifications
1. Tuner & channel
Input connector 1 x F type with loop through
Output connector 1 x F type 75 Ohm, IF signal out
Frequency range 950MHz to 2150MHz
Input impedance 75 Ohm
Signal level -25 to -65dBm
IF frequency 480MHz
IF bandwidth 36MHz
LNB power & polarization Vertical +13.5V~+14.5V
Horizontal +17.5V~+18.5V
22kHz tone Frequency 22kHz ±2kHz
Amplitude 0.6Vp-p ±0.2Vp-p
Demodulation QPSK
Input symbol rate 2~32Msps
FEC decoder Convolutionalcode rate
1/2, 2/3, 3/4, 5/6 and 7/8 with constraint
Length K=7
2. MPEG transport stream A/V decoding
Transport stream MPEG-2 ISO/IEC 13818
Transport stream specification
Profile & level MPEG-2 MP @ ML
Input T/S data rate 90Mbit/S max.
Aspect ratio 4:3, 16:9 with pan vector
Video resolution 720 x 576 (PAL), 720 x 480 (NTSC)
Audio decoding MPEG audio layer 1 & 2, musicam
Audio mode Stereo, dual channel, joint stereo, mono
Sampling rate 32, 44.1 and 48kHz
3. Memory
Flash memory 2M bytes
Program DRAM 8M bytes
EEPROM 2K bytes