EchoStar DSB-1200 Viaccess User manual

USER MANUAL
DSB-1200 Viaccess©
Digital Satellite Receiver
Printedonrecycledpaper

Issue: DSB-1200-B-3A
© 2001 EchoStar International Corporation - The Netherlands
We encourage you to express your thoughts on this user manual.
Please send your comments to:
EchoStar International Corporation
Technical Publications Department
Schuilenburghlaan 5a
7604 BJ Almelo
The Netherlands

Preface
Digital Satellite Receiver Page I
© 2001 EchoStar International Corporation
All rights reserved
PREFACE
1. DEAR CUSTOMER
Thank you for purchasing an EchoStar satellite receiver. This receiver is of the latest
generation for which it is possible to upgrade the software to keep up with the newest
developments. Please read this user manual carefully, to be able to safely install, use and
maintain the receiver for maximum performance. Keep this user manual next to your receiver
for future reference.
Please make a note of the serial number in the space below. This helps to trace and identify
thereceiverincaseoftheft.Alsoquestionstoourhelpdeskcanbeansweredmoreaccurate
if you can provide the details as mentioned on the serial number plate. You find the serial
number plate at the rear panel of the receiver.
2. INTENDED USE
This user manual is intended for anyone who uses an EchoStar satellite receiver. It can be
used by both first-time and experienced users of satellite receivers who want to install, use
and maintain their receiver.
This user manual is applicable for the EchoStar DSB-1200 Viaccess©Digital Satellite
Receiver and the related accessories. This user manual is divided into separate sections and
chapters. For easy access to the information, a clear table of content and an index are
provided.
3. WARRANTY
EMBEDDED VIACCESS SMART CARD READER AND SMART CARDS
For pay-services, please only use smart cards which are approved by the service provider of
the encrypted program you want to receive. Only this will enable the receiver to work
properly.
Anomalies can occur when unapproved smart cards are used. EchoStar cannot and will not
accept any responsibility for the performance of such smart cards. If you use unapproved
smart cards, EchoStar is no longer able to provide any assistance or support. Use of
unapproved smart cards will void any warranty claim. If you have any doubt which smart
cards are approved, please ask your service provider for assistance.
4. DISCLAIMER
EchoStar International Corporation has to the best of her abilities, everything done to supply
you with the most up-to-date information. EchoStar International Corporation makes no
warranties with respect to the information provided by this user manual and specifically
disclaims any implied warranties of merchantability or fitness for any particular purpose. The
information provided is meant as a guideline for the use and maintenance of the receiver.
EchoStar International Corporation reserves the right to revise, change or translate this user
manual without the obligation to notify any person or organization of such change. Therefore,
please visit our website, on a regular basis, for the latest information and software available.
Type: ...........................................................................
S/N: ..............................................................................
Software Version: .......................................................

Preface
Page II EchoStar DSB-1200 Viaccess
© 2001 EchoStar International Corporation
All rights reserved
5. COPYRIGHT AND TRADEMARKS
© 2001 EchoStar International Corporation. All rights reserved worldwide. This user manual
has been provided pursuant to an agreement containing restrictions on its use. This user
manual is also covered by Federal Copyright Law.
No part of this user manual may be copied, distributed, transmitted, stored in a retrieval
system or translated into any human or computer language, in any form or by any other
means, electronically, mechanically, magnetically, manually or otherwise or disclosure to third
parties without the express written permission of EchoStar International Corporation.
EchoStar International Corporation is possibly in the possession of patents, requests for
patent approval, trademarks, copyrights and other intellectual property with respect to the
contents within this user manual. The submission of this user manual does not imply you
have got any license or other legal right for the use of the here above mentioned without the
express written permission of EchoStar International Corporation.
■EchoStar, EchoNAV and Quality has a name
are registered trademarks of EchoStar International Corporation;
■DVB, Digital Video Broadcasting
is a registered trademark of the The Digital Video Broadcasting Project (DVB) which is an
industry-led consortium of over 300 broadcasters, manufacturers, network operators,
software developers, regulatory bodies and others in over 35 countries committed to
designing global standards for the delivery of digital television and data services.
■Dolby Digital
Dolby, Dolby Digital, AC-3 and Dolby Pro Logic are registered trademarks of the Dolby
Laboratories Licensing Corporation;
■Viaccess©
Viaccess is a registered trademark of VIACCESS SA, a France Telecom Group company
that delivers end-to-end solutions for digital pay-TV services and multimedia applications,
built around our DVB MPEG-2 compatible VIACCESS©Conditional Access System, and
interactively engines such as OpenTV.
■All other trademarks are the property of their respective owners or companies.

Preface
Digital Satellite Receiver Page III
© 2001 EchoStar International Corporation
All rights reserved
TABLE OF CONTENTS
Preface
1 DEAR CUSTOMER 1-I
2 INTENDED USE 1-I
3WARRANTY 1-I
4DISCLAIMER 1-I
5 COPYRIGHT AND TRADEMARKS 1-II
Safety Information
1 GENERAL SAFETY 1-1
2 ELECTRICAL SAFETY 1-1
3 NOTATIONAL CONVENTIONS USED IN THIS MANUAL 1-2
4 SYMBOLS USED ON THE RECEIVER 1-2
Preparation
1 STORAGE AND TRANSPORT 2-1
2 TO UNPACK YOUR RECEIVER 2-1
3 THE CONTENTS OF THE BOX 2-1
4 THE DISPOSAL OF YOUR PACKING MATERIALS 2-1
5 TO SETUP YOUR PERIPHERAL EQUIPMENT 2-2
6 TO SETUP THE RECEIVER 2-2
Installation
1 CONNECT YOUR EQUIPMENT 3-1
2 CONNECT A DISH 3-2
3 TO SETUP YOUR RECEIVER FOR THE FIRST TIME 3-3
Familiarization
1 THE RECEIVER 4-1
2 THE ECHONAV INSTALLATION MENU 4-4
3 THE ECHONAV MODE AND SELECTION MENUS 4-12
4 THE ELECTRONIC PROGRAM GUIDE (EPG) 4-15
5 THE INFOBANNER AND POP-UP MENUS 4-16
Operation
1 TO NAVIGATE THROUGH THE MENUS 5-1
2 USE THE FAVORITE LISTS 5-7
3 TO USE THE ELECTRONIC PROGRAM GUIDE (EPG) 5-10
4 TO SET THE USER PREFERENCES 5-14
Maintenance
1 HARDWARE MAINTENANCE 6-1
2 SOFTWARE MAINTENANCE 6-1
3 END OF LIFE DISPOSAL 6-7
Troubleshooting
1 TO SOLVE A PROBLEM 7-1
Glossary
1 LIST OF USED ABBREVIATIONS 8-1
2 EXPLANATION OF USED TERMINOLOGY 8-1
Index

Preface
Page IV EchoStar DSB-1200 Viaccess
© 2001 EchoStar International Corporation
All rights reserved
Appendix 1
1 LNB CONFIGURATION MATRIX A-1
2 LNBF CONFIGURATION MATRIX A-1
3 USER DEFINED LNB(F) MATRIX A-1

Safety Information Section 1
Digital Satellite Receiver Page 1 - 1
© 2001 EchoStar International Corporation
All rights reserved
1
SAFETY INFORM ATION
1. GENERAL SAFETY
Read this manual carefully and make sure you understand the instructions given. For your
safety, know what the reaction upon each action will be. Do not perform any actions which are
not described in this manual, failing to do so might result in an uncontrolled behavior of the
receiver or even in a hazardous situation for persons and/or equipment.
Disconnect the receiver from the mains before you start any maintenance or installation
procedures. Do not use alcohol or ammonia based liquids to clean the receiver. If required,
clean with a soft lint-free cloth slightly made damp with a mild soap solution.
Consult an authorized service technician if the receiver does not operate normally when the
instructions in this user manual are strictly followed. Do not to attempt to open the receiver, as
youwillbeexposedtoashockhazard.
Do not put any objects on top of the receiver which could fall through the ventilation slots or
which could cover them and prevent proper cooling of the components inside.
Do not put any (foreign) objects into the ventilation slots. This can cause fire or an electrical
shock by shorting the internal components.
Make sure that nothing rests on the receivers cables and that the cables are not located
where they can cause injury to persons and pets (e.g to stumble over, eat the cable).
Do not install the receiver:
■in a closed or poorly ventilated cabinet;
■directly on top of or under another equipment;
■on a surface which will obstruct the ventilation slots.
Do not expose the receiver and it’s accessories:
■to rain or excessive moisture to avoid the risk of shock or permanent damage to your
receiver;
■to direct sunlight, heaters, stoves or any other heat generating equipment;
■to any magnetic objects, such as speakers, electric motors, transformers, etc.;
■to excessive vibration.
To help avoid possible damage to the receiver’s electronics:
■wait 5 seconds after you switched off the receiver before you move the receiver or discon-
nect any equipment;
■do not touch the components or the chip area on the smart card and hold the smart card
by it’s edges.
2. ELECTRICAL SAFETY
When using or connecting electrical equipment always observe the safety regulations
applicable in your country to reduce the risk of fire, electrical shock, and personal injury.
Read and comply at least with the given safety instructions.
■Always make sure that the electrical power supply corresponds with the voltage on the
electrical identification plate at the rear of the receiver next to the electrical cord.
■Your receiver is double insulated and complies with the EN 50144; therefore no additional
earth wire is required, though the use of an earth leak switch and/or over voltage protec-
tion switch is recommended.
■Only use an approved extension (convenience) lead suitable for the electrical power con-
sumption of the installed equipment.

Section 1 Safety Information
Page 1 - 2 EchoStar DSB-1200 Viaccess
© 2001 EchoStar International Corporation
All rights reserved
3. NOTATIONAL CONVENTIONS USED IN THIS MANUAL
3.1. WARNINGS, CAUTIONS AND NOTES
Throughout this user manual, there may be blocks of text indicated by symbols and printed in
a different way then the surrounding text. These blocks of text ask the attention of the reader
to avoid hazardous situations. The hazard levels are indicated as:
4. SYMBOLS USED ON THE RECEIVER
The next paragraphs explain the meaning of the symbols, present on the receiver.
4.1. SYMBOLS ON THE FRONT PANEL
4.2. SYMBOLS ON THE REAR PANEL
WARNING
THIS INDICATES A HAZARDOUS SITUATION WHICH,IF NOT AVOIDED,COULD RESULT IN
(SERIOUS)INJURY.
CAUTION
This indicates a situation which, if not avoided, could damage the equipment or
other properties.
NOTE
This indicates additional information to the user to make the user aware of possible
problems and information of any importance to help the user to understand, to use
and to maintain the installation.
The Dolby Digital logo.
This logo tells you that this receiver is compliant with the Dolby Digital
standard.
The Digital Video Broadcasting logo.
This logo tells you that this receiver is compliant with the DVB standard.
The Viaccess logo.
This logo tells you that this receiver has an embedded Viaccess smart card
reader. The required smart card has to be obtained from a service provider
who scrambles the programs according the Viaccess encryption method.
The caution ‘risk of electrical shock - do not open’ symbol
This symbol tells you that you are not allowed to open the receiver. Only
authorized (service) technicians are allowed to open the box.
The CE mark.
This mark tells you that the receiver is following the provisions of Council
Directive 89/336/EEC on the approximation of the laws of the Member States
relating to the electromagnetic compatibility and the provisions of Council
Directive 73/23/EEC and 93/68/EEC on the approximation of the laws of the
Member States relating to low voltage and electrical safety.
The double insulation symbol.
This symbol tells you that the receiver is electrically safe within the normal
use of the receiver as stated in the safety chapter.

Preparation Section 2
Digital Satellite Receiver Page 2 - 1
© 2001 EchoStar International Corporation
All rights reserved
2
PREPARATION
1. STORAGE AND TRANSPORT
The receiver and it’s accessories are delivered in a protective packaging. This packaging is
designed to protect against excessive shocks and not against ingress of moisture.
1.1. STORAGE
If necessary:
■store the receiver in it’s original protective packaging;
■in a room with the ambient conditions as stated in the technical specifications.
1.2. TRANSPORT
Pack the receiver preferably in the original packaging or in an equally protective packaging.
This is to help avoid possible damage to the receiver’s electronics.
2. TO UNPACK YOUR RECEIVER
When you unpack the contents of the box, confirm that all the parts are included. Refer to
Chapter 3. The contents of the box.
Unpack the contents of the box carefully. Electronic equipment as satellite receivers are
easily damaged when you handle it roughly. Examine all parts for damage that may have
occurred during shipment. If you find any damage, stop to unpack the box and call the retail
seller where you bought the receiver.
To help avoid possible damage to the receiver’s electronics, allow the receiver to adapt to the
ambient temperature and humidity level. This to avoid condensation caused by a sudden
change in temperature (e.g from a hot car into a cool room).
3. THE CONTENTS OF THE BOX
The box contains:
■A receiver;
■A remote control unit;
■A pair of batteries (for the remote control unit);
■A set of documentation.
4. THE DISPOSAL OF YOUR PACKING MATERIALS
Most of the packaging materials can be recycled. Please discard these materials in an
environmental safe manner
DANGER
KEEP AWAY THE PLASTIC PACKAGING FROM CHILDREN.THE PLASTIC PACKAGING MAY
CLING TO NOSE AND MOUTH AND PREVENT BREATHING.
CAUTION
It is recommended to keep the packaging materials for a period of time. In case of
warranty claims, we can request to return the receiver in the original packaging to
protect the electronics and hard disk drive. Failing to do so might void the warranty.
ENVIRONMENTAL REMARK
Dispose the packaging in an environmental safe manner. Please inform yourself
on local regulations with respect to the disposal of reusable materials.

Section 2 Preparation
Page 2 - 2 EchoStar DSB-1200 Viaccess
© 2001 EchoStar International Corporation
All rights reserved
5. TO SETUP YOUR PERIPHERAL EQUIPMENT
Please refer to the user manuals of your terrestrial antenna, dish, TV, video recorder and/or
audio equipment to make sure this equipment is properly installed and configured before you
install the receiver.
EchoStar recommends that you follow at least the following instructions:
5.1. THE TERRESTRIAL ANTENNA
1. Make sure:
■The terrestrial antenna is in good condition and well aligned for the best reception
(avoid corroded contacts);
■The UHF coaxial cable is in a good condition (no excessive bends or damaged
insulation);
■The UHF coaxial cable connections are well shielded (metal connectors).
2. If necessary, do any work.
5.2. THE DISH
1. Make sure:
■The outdoor components of the dish are good condition;
■The dish is well aligned for the best reception;
■The dish is connected with the correct UHF coaxial cable (75 Ohm) and connectors;
■The cables from the dish are in a good condition (no excessive bends or damaged
insulation).
2. If necessary, do any work.
5.3. THE TV, VIDEO RECORDER AND AUDIO EQUIPMENT
1. Make sure:
■Safe access to the connections is available;
■The equipment is switched off;
■It is safe to remove and install the cables.
2. If necessary, do any work.
6. TO SETUP THE RECEIVER
6.1. THE RECEIVER
You can install the receiver safely in a convenient location if you adhere to the warning:
WARNING
DO NOT INSTALL THE RECEIVER:
■in a closed or poorly ventilated cabinet;
■directly on top of or under another equipment;
■on a surface which will obstruct the ventilation slots.
DO NOT EXPOSE THE RECEIVER AND IT’S ACCESSORIES:
■to rain or excessive moisture to avoid the risk of shock or permanent damage to
your receiver;
■to direct sunlight, heaters, stoves or any other heat generating equipment;
■to any magnetic objects, such as speakers, electric motors, transformers, etc.;
■to excessive vibration.

Installation Section 3
Digital Satellite Receiver Page 3 - 1
© 2001 EchoStar International Corporation
All rights reserved
3
INSTALLATION
1. CONNECT YOUR EQUIPMENT
It is possible to connect the different equipment with the use of UHF coaxial cables,
SCART cables, and/or so called audio/video cables with RCA connectors.
CONNECTION WITH UHF COAXIAL CABLES
1. On the TV, find the UHF-coaxial cable that is connected to the terrestrial antenna or cable
network.
2. Remove the UHF-coaxial cable from the TV and make sure the cable condition is OK.
3. On the rear panel of the receiver find the TV OUT connector.
4. Install an UHF-coaxial cable between the TV OUT connector (receiver) and the antenna
connector (TV).
5. On the rear panel of the receiver find the ANT IN connector.
6. Install the UHF-connector (terrestrial antenna) to the ANT IN connector (receiver).
CONNECTION WITH SCART CABLES
1. On the TV find the SCART cable that is connected to the VCR.
2. Remove the SCART connector that is connected to the VCR from the TV.
3. On the rear panel of the receiver find the TV and VCR SCART connectors.
4. Install the SCART cable between the VCR and the VIDEO SCART connector (receiver).
5. Install a full featured SCART cable between the TV SCART connector (receiver) and the
SCART connector on the TV (old SCART connection to the VCR).
CONNECTION WITH AUDIO/VIDEO CABLE (RCA-CONNECTORS)
1. On the rear panel of the receiver find the VIDEO, AUDIO L and AUDIO R connectors.
2. Install an audio/video cable between:
a. the VIDEO connector of the receiver and TV (yellow);
b. the AUDIO L connector of the receiver and TV (white);
c. the AUDIO R connector of the receiver and TV (red).
CONNECTION WITH DOLBY DIGITAL AUDIO CABLE (RCA-CONNECTORS)
1. On the rear panel of the receiver find the S/PDIF connector.
2. Install an audio/video cable (black) between:
a. the S/PDIF connector (receiver) and Dolby Digital connection of the Dolby digital
compatible installation.
CONNECTION WITH SERIAL CABLE (0-MODEM CABLE)
1. On the rear panel of the receiver find the SERIAL PORT connector.
2. Install a serial cable between the SERIAL PORT connector (receiver) and the serial port
connection of the PC.
WARNING
ALL EQUIPMENT INVOLVED IN THE INSTALLATION TASK MUST BE INSTALLED CORRECTLY
ANDSWITCHEDOFF
.MAKE SURE THAT IT IS SAFE TO PROCEED WITH THE INSTALLATION
TASK.UNSAFE CIRCUITS AND INSTALLATIONS CAN CAUSE (SERIOUS)INJURY OR DAMAGE
TO EQUIPMENT.

Section 3 Installation
Page 3 - 2 EchoStar DSB-1200 Viaccess
© 2001 EchoStar International Corporation
All rights reserved
2. CONNECT A DISH
It is possible to connect the different dish configurations with the use of RF coaxial cables.
Only the most common configurations are discussed. If in doubt, please ask the EchoStar
service department for advice.
1. On the dish installation, connect a RF cable (for detailed instructions, refer to the
manufacturer’s instructions).
2. On the rear panel of the receiver find the LNB IN (digital) and the IF OUT connectors
FIXED DISH INSTALLATION WITH LNB(F)
3. Install the F-connector (dish) to the LNB IN connector (receiver).
FIXED DISH INSTALLATION WITH DISEQCSWITCH
3. Install the F-connector (DiSEqC switch) to the LNB IN connector (receiver).
MOVEABLE DISH INSTALLATION WITH DISEQC1.2
3. Install the F-connector (DiSEqC 1.2 motor) to the LNB IN connector (receiver).
.
WARNING
ALL EQUIPMENT INVOLVED IN THE INSTALLATION TASK MUST BE INSTALLED CORRECTLY
ANDSWITCHEDOFF
.MAKE SURE THAT IT IS SAFE TO PROCEED WITH THE INSTALLATION
TASK.UNSAFE CIRCUITS AND INSTALLATIONS CAN CAUSE (SERIOUS)INJURY OR DAMAGE
TO EQUIPMENT.
CAUTION
Tighten the cable connectors only by hand. Do not use any tools. You will damage
the connector pins if you overtighten the connector. This will result in loss of signal
quality, or even total loss of reception.

Installation Section 3
Digital Satellite Receiver Page 3 - 3
© 2001 EchoStar International Corporation
All rights reserved
3
3. TO SETUP YOUR RECEIVER FOR THE FIRST TIME
This procedures will guide you step-by-step through the initial setup of the receiver. After you
have finished the initial installation, these pages are accessible through the icons in the menu
bar which is in the initial setup not shown.
NOTE
Unless otherwise specified; This note explains the way you can navigate through
the pages of the EchoNAV initial setup menu.
1. Use the OK key to pull down the menu selection fields.
2. Use thearrow keys to go through the selectable menu items.
3. In a pull-down menu, use the OK key to confirm the selection.
4. Use thearrow keys to navigate between the left and right column of
selectable menu items.
5. Use the EXIT key to leave the menu and return to the live mode.
1. Switch on the TV.
2. On the receiver, press the on/standby key.
■The receiver display shows:
- first a moving dot;
- then it shows - - - -
■The TV shows the first page.
3. Make the required selections.
4. Read the available help text for information.
5. Go to the Continue field.
6. On the RCU, press the OK key to advance.
7. Make the required selections.
8. Read the available help text for information.
Note that only the white fields are selectable,
other fields show reference information.
9. Go to the Continue field.
10. On the RCU, press the OK key to advance.
11. Make the required selections.
12. Read the available help text for information.
13. Go to the Continue field.
14. On the RCU, press the OK key to advance.

Section 3 Installation
Page 3 - 4 EchoStar DSB-1200 Viaccess
© 2001 EchoStar International Corporation
All rights reserved
FOR FIXED AND DISEQC1-4SWITCH INSTALLATIONS
NOTE
The receiver needs the correct local time to collect and show the EPG (Electronic
Program Guide). An incorrectly entered local time will result in no EPG information.
15. Make the required selections.
16. Read the available help text for information.
17. Go to the Press OK to set the time.
Note that the local time is shown correctly.
18. On the RCU, press the OK key to advance.
19. Go to the Continue field.
20. On the RCU, press the OK key to advance.
NOTE
From the next step onwards, the procedure is divided into different configurations.
The configurations are; Fixed, DiSEqC 1.2 and SMATV.
■Fixed means set up a single dish or multiple dishes with DiSEqC1..4 switch;
■DiSEqC 1.2 means set up a moveable dish according the DiSEqC 1.2 spec;
■SMATV means set up for television distribution (cable network in buildings).
21. Make the required selections.
22. Read the available help text for information.
Note that only the white fields are selectable,
other fields show reference information.
23. Go to the Check Signal field.
24. On the RCU, press the OK key to advance.
25. Wait for the Checking Configuration to complete.
26. Make the required selections.
27. Read the available help text for information.
28. If the red dot in the transponder field stays:
a. select another transponder;
b. go to the check signal field;
c. on the RCU, press the OK key.
29. Go to the Search Channels field.
30. On the RCU, press the OK key to advance.

Installation Section 3
Digital Satellite Receiver Page 3 - 5
© 2001 EchoStar International Corporation
All rights reserved
3
FOR MOVEABLE DISH INSTALLATIONS (DISEQC1.2)
31. Wait for the search to complete:
a. the receiver display shows a moving dot;
b. the search completed popup menu appears.
32. On the RCU, press the OK key. to end the initial
setup procedure.
22. Make the required selections.
23. Read the available help text for information.
Note that only the white fields are selectable,
other fields show reference information.
24. Go to the Program Satellites field.
25. On the RCU, press the OK key to advance.
26. Wait for the Checking Configuration to complete.
27. Make the required selections.
28. Read the available help text for information.
29. Monitor the signal indicator for best signal when
you set the location.
30. On the RCU, press OK to save the setting.
31. Go to the Search Channels field.
32. On the RCU, press the OK key to advance.
33. Wait for the search to complete:
a. the receiver display shows a moving dot;
b. the search completed popup menu appears.
34. On the RCU, press the OK key. to end the initial
setup procedure.

Section 3 Installation
Page 3 - 6 EchoStar DSB-1200 Viaccess
© 2001 EchoStar International Corporation
All rights reserved
FOR SMATV INSTALLATIONS
22. Make the required selections.
After the initial installation it is possible to add
more symbol rates. Refer to section Maintenance
for detailed instructions.
23. Read the available help text for information.
24. Go to the Search Channels field.
25. On the RCU, press the OK key to advance.
26. Wait for the search to complete:
a. the receiver display shows a moving dot;
b. the search completed popup menu appears.
27. On the RCU, press the OK key. to end the initial
setup procedure.

Familiarization Section 4
Digital Satellite Receiver Page 4 - 1
© 2001 EchoStar International Corporation
All rights reserved
4
FAMILIARIZATION
1. THE RECEIVER
The digital satellite receiver has an embedded Viaccess smart card reader. The front panel
gives you the control over the basic functions. The rear panel gives you various connections
to connect the audio and video equipment as well as a terrestrial and dish antenna.
Ventilation slots in the housing are provided for cooling of the internal electronics.
The software of the receiver contains the EchoNAV user interface with on-screen help, which
gives you easy control over the features of the receiver. The software contains also a large
database of pre-programmed satellites and transponders which are used for a quick
installation. For initial installation, the software guides you through the required setup menu to
allow for an easy and reliable installation setup of the receiver.
FEATURE HIGHLIGHTS
■EchoNAV Multi-Lingual advanced User Interface (12+ languages);
■Embedded Viaccess 1.1;
■7dayEPG;
■4,000 Digital Channels, 100 Satellites, 1,300 Transponders;
■8 Favorite Channel Lists for TV and 8 for radio;
■Powerful Channel Sorting and Grouping;
■Multiple Scan Modes (incl.Update Scan);
■Digital Audio Output (Dolby Digital Compatible);
■DiSEqC 1.2;
■Software Update via Internet/Satellite.
1.1. THE RECEIVER FRONT PANEL
The front panel has:
■The display,
to show the clock or the actual status of the receiver.
■The key,
to switch the receiver to on or stand-by.
■The MENU key,
to get access to the EchoNAV installation menu.
■The OK key,
to get access to the EchoNAV mode and selection menu.
■The arrow keys,
to navigate left, up, right and down through the selectable options.
■The access door,
to access the slot for the embedded Viaccess smart card reader.

Section 4 Familiarization
Page 4 - 2 EchoStar DSB-1200 Viaccess
© 2001 EchoStar International Corporation
All rights reserved
1.2. THE RECEIVER REAR PANEL
The rear panel gives you various connections to connect the audio and video equipment as
well as a terrestrial and dish antennas. Depending on the installation setup, you may not use
all connectors, but they are provided for any desired setup in future.
The available connectors on the rear panel are:
■The LNB IN connector (F-type),
for the connection of a dish to the
receiver, to receive the digital
broadcasts;
■The SERIAL PORT connector (sub-D),
for the connection to the serial
communication port of a PC;
■The IF OUT DIGITAL connector
(F-type), for a loop through connection;
■The ANT IN connector (IEC),
for the connection of an terrestrial TV
antenna;
■The S/PDIF connector (RCA),
for the connection of Dolby Digital (AC-3)
compatible audio equipment;
■The TV OUT connector (IEC),
for the connection to the antenna
connector of a TV or a VCR;
■The VIDEO connector (RCA),
for the connection to the composite
video input of the TV (monitor);
■The VCR connector (SCART), for the
connectionofaVCRwiththeuseofa
fully-featured SCART-cable;
■The AUDIO L connector (RCA),
for the connection of the left audio input
channel of a stereo set;
■The TV connector (SCART),
for the connection of a TV with the use of
a fully-featured SCART-cable;
■The AUDIO R connector (RCA),
for the connection of the right audio input
channel of a stereo set;

Familiarization Section 4
Digital Satellite Receiver Page 4 - 3
© 2001 EchoStar International Corporation
All rights reserved
4
1.3. THE REMOTE CONTROL UNIT (RCU)
The EchoStar Remote Control Unit (RCU) is used to control the receiver.
The RCU requires two AA/R6 alkaline batteries to operate.
1.4. THE ECHONAV USER INTERFACE
The EchoNAV user interface is designed to give you easy control over the receiver. The
EchoNAV user interface has four main features that give access to the different functions.
Thefourmainfeaturesare:
■The EchoNAV installation menu,
that helps you to setup the receiver and access the parental lock settings;
■The EchoNAV user menu,
that helps you to control the daily operation and selection of the favorites;
■The EchoNAV EPG menu,
that helps you to control the different timers and to view the available EPG;
■The EchoNAV InfoBanner,
that helps you to view the available information about the actual mode.
■ON/STANDBY
To switch to standby or on.
■EPG
To view the EPG.
To return to current time
■ALT SUBTITLE
To choose a subtitle.
■MENU
To go to the installation
menu.
■VOL+
To increase the volume.
■VOL-
To decrease the volume.
■ARROW CLUSTER
To go left, right, down or
left.
■OK/STORE
To go to the (favorites) lists;
To make a menu selection;
To pull down a menu.
■PAGE+
To go up one page.
■PAGE -
To go down one page.
■RED
To go to another mode.
TV/RAD
To switch to TV or Radio
mode.To view detailed
EPG information.
■BLUE
To sort a list;
To zoom in/out the time slot
of the EPG view window.
■MUTE
To blank out the volume.
■i
To view the InfoBanner;
To access extended info
■NUMBER KEYS
To enter numerical
settings;
To type in a channel
number.
■EXIT
To leave a menu or feature.
■CH+
To go one channel up.
■CH-
To go one channel down.
■RCL
To go to the previous
channel;
To access special features.
■GREEN
To select a (favorites) list.
FAV
To go to the favorite list of
the actual mode.
■YELLOW
To group a list;
To select an EPG timer.
ALT AUDIO
To choose a language.
■WHITE
To go to the edit mode

Section 4 Familiarization
Page 4 - 4 EchoStar DSB-1200 Viaccess
© 2001 EchoStar International Corporation
All rights reserved
The EchoNAV user interface has various ways to navigate through the menus and functions.
Some of the keys on the remote control unit give direct access to functions. The most
important keys are identified as EPG, i, colored keys, MENU and OK. Other keys are multi-
functional which means that their function changes dependent of the mode that you are in.
2. THE ECHONAV INSTALLATION MENU
The EchoNAV installation menu has different main menus that give you access to the
different sub-menus. The main menus are:
■The guided initial setup menu which is only accessible after the first time you switch the
receiver on and after every manually initiated factory reset;
■The User Preferences menu, the installation setup menu and the conditional access menu
are accessible at any time.
NAVIGATION
A highlighted button shows you which (main/sub) menu is selected. The MENU key lets you
change between the main and sub menu where thekeys let you make a selection in the
selected (main/sub) menu. The OK key brings you into the related page, where you can make
a choice from the available options.
■The button, that gives you access to the User Preferences menu;
■The button, that gives you access to the installation setup menu;
■The button, that gives you access to the Conditional Access menu.
NOTE
Unless otherwise specified; this note explains the way you can navigate through
the pages of the EchoNAV user menu.
1. Use the OK key to pull down the menu selection fields.
2. Use the  keys to scroll the selectable items.
3. Use the  keys to navigate between the left and right column of selectable
items.
4. Use the EXIT key to leave the menu and return to the view mode.
5. In a pull-down menu:
- use the OK key to confirm the selection.
- the yellow bar indicates the active selection;
- on the left, the green page indicator indicates where you are.
NOTE
Once in a page, at any time:
■you can use the MENU key to reverse from a menu page to the sub menu bar;
■you can easily leave with the EXIT key.
The main menus are divided into sub-menus,
selection pages and option fields. The main menu
buttons are shown at the right hand side of the menu
bar. The different sub-menu buttons are shown on the
left hand side of the menu bar.
The selection pages with the option fields are
accessible after you have selected a sub-menu.
Every menu, sub-menu and selection page has one or
more help lines to assist you.
The main menus are accessible with: